FRANCO BELGE 174 10 54 Le Beffroi User manual

Description of the appliance
Installation instructions
Operating instructions
Spare parts
Warranty certificate
Document n° 954-6 ~ 29/04/2004
STAUB FONDERIE
Head Office Address
2, rue Saint Gilles
68230 TURCKHEIM
RC Colmar
SIREN 439 330 325
Address - Administration and
manufacturing
BP 73
59660 MERVILLE (FRANCE)
Telephone : [phone]
Fax : [phone]
Subject to modifications.
Le Beffroi
Oil fired stove
Model 174 10 54
EN NO
Technical manual
to be saved
by the user
for future reference.

2Technical manual “954”
“Le Beffroi” ref. 174 10 54
CONTENTS
Description of the unit ...................................p.3
Description . ...............p.3
Package :.................p.3
Optional equipment ...........p.3
Specifications . . . . . . . . . . . . . . p. 3
Operating principle. . . . . . . . . . . . p. 4
Installation instructions ..................................p.5
Position of the unit ............p.5
Chimney .................p.5
External tank ...............p.5
Chimney connector ...........p.6
Mounting the levelling feet .......p.6
Smoke exit at the top . . . . . . ....p.6
Smoke exit at rear ............p.6
Casing assembly. . ...........p.6
Levelling . . . . . . . . . . .......p.7
Oil flow adjustment . . . . . . . . . . . p. 7
Chimney draught. . . . . . . . . . . . . p. 8
Door closing pressure . . . . . . . . . . p. 8
Pre-utilisation check . . . . . . . . . . . p. 8
Mounting mirrors (Optional) . . . . . . . p. 8
Maintenance of the Chimney . . . . . . p. 8
Operating instructions ...................................p.9
Fuel . . . .................p.9
Lighting procedure ............p.9
Operating procedure...........p.9
Shutting down ..............p.9
Maintenance of the stove . . . . . . . . p. 9
Recommendation . . . . . . . . . . . . p. 10
Trouble shooting . . . . . . . . . . . . p. 11
Spare parts .........................................p.12
FRANCO BELGE congratulates you on your choice.
FRANCO BELGE, which has been granted the ISO 9001 certification, guarantees the quality
of its appliances and is committed to meet its customers’ needs.
FRANCO BELGE, which can boast a 75-year experience in the industry of heating devices,
uses state-of-the-art technologies
to design and manufacture its whole range of products.
This document contains instructions on how to install your appliance and make full use of
its functions, both for your comfort and safety.

This appliance is an oil-fired stove.
WARNING
An incorrectly installed oil-fired stove can cause serious accidents.
This appliance should only be installed by competent personnel.
1. Description of the unit
1.1. Description
Flued oil stove with vaporizing burner
(Norm EN1 - NF D 35-385).
1.2. Package :
•1 stove
•1 casing
-Natural stone casing 72554
-Enamelled panels :
Beige 72553 - Red 72605 - Blue 72606
-Marble panels :
Black 72805 - Beige 72806 - Gray 72807
1.3. Optional equipment
•Brass-rampe : KR 134 08.
•Mirrors : P 174 10 53
•Vent-pipe.
1.4. Specifications
Model ................. 1741054
Nominal heat output ........kW 10
.................BTU/hr 34130
Oil consumption at :
- maximum speed .........l/h 1,20
..................gal/hr 0.317
- minimum speed ........litre/h 0,25
..................gal/hr 0,066
Chimney draft required at :
- maximum speed .........Pa 14
- minimum speed .........Pa 5
Weight ................kg 138
Technical manual “954” 3
“Le Beffroi” ref. 174 10 54 Description of the unit
564
2 1 4 6 0 4
1 0 5 29 1 5
Ø 1 2 0 / 1 2 5
624
Fig. 1 - Dimensions in mm

1.5. Operating principle
Furnace oil is fed to the burner floor (fig. 2) where is it
ignited by means of a firestarter. The heat produced by
this flame brings the burner temperature to the required
level to vaporize the fuel. Oil will only burn as a vapour
not a liquid.
Room combustion air enters the burner through the air
inlet holes (# 1).
In the center of the burner is the catalyser (# 2) which
aids in vaporizing the fuel. When the stove is operation,
the catalyser glows red. The stove should not be used
with out both the catalyser (# 2c), catalyser top (# 2b)
and ring (# 2a).
A de-scaling lever (# 5) can be pushed and pulled in and
out as well as turning slightly at the same time to keep
the inlet pipe clear of carbon buildup.
The stove float regulator (fig. 3) contains a filter (# G) to
trap impurities.
A safety lever (# B) controls fuel flow. Oil can only enter
the float chamber when the safety lever is depressed.
Oil temperature variations will affect the oil flow into the
float chamber. A float in the chamber raises the fuel
level available to the burner.
The carburetor is also controlled by a control knob
which turns from “0" (off) to ”6" (high setting).
A draft regulator (# 1, fig. 11) ensures a constant air
intake to the burner regardless of external factors.
4Technical manual “954”
“Le Beffroi” ref. 174 10 54 Description of the unit
1
22 b
2 c
3
4
5
2 a
Figure 2 - Burner
1- Air holes
2- Catalyser
2a : Upper ring
2b : Catalyser top
2c : Catalyser body
3- Burner pot
4- Automatic ignition
(optional)
5- De-scaling lever
Figure 3 - Float regulator
A- Control knob
B- Safety lever.
C- Main float
D- Safety float
E- Oil level regulator
F- Thermostat control
G- Filter
A
F
B
E
G
C
D

2. Installation instructions
SAFETY NOTICE : Read carefully all instructions
before starting the installation. If the stove is not
properly installed, a house fire may result. For your
safety, follow the installation directions. Contact local
building or fire officials about restrictions and
installation inspection in your area.
2.1. Position of the unit
-The position of the appliance must be chosen very
carefully in order to obtain the best possible results for
heat distribution.
-Position the unit to comply with the minimum
clearances to combustible material. Minimum
clearances are shown from the vertical portion of the
chimney connector. Check that no overhead cross
members in the ceiling will be cut. Reposition unit if
necessary, being careful not to move closer than the
minimum clearances.
-Outside air : For the oil stove to function properly, an
adequate supply of combustion air is required.
2.2. Chimney
-Ensure that the flue has sufficient draught (refer to
technical details).
-Minimum flue diameter, 10 cm (4" I.D).
-The chimney must be at least 4.5 m (15 ft high).
-The flue must not be shared with any other appliance.
-Downdraughts caused by obstacles close to the
chimney top may sometimes be prevented by fitting an
anti-downdraught cap to the top of the chimney.
-The chimney must have a constant cross section. Too
large a flue could affect the chimney draught.
-The chimney must be soundly constructed, in order to
prevent cold air infiltration.
-The flue must be well insulated, water and air tight. A
chimney with a cold internal surface can prevent a
good chimney draught and condensation will occur.
-The flue must be swept at least once a year.
2.3. External tank
A barometric fuel tank should not be positionned where
it will be in the direct rays of the sun or adjacent to a
source of intense heat.
If the tank is more than 8 ft (2,5 m) higher than the stove
a pressure reducer must be installed on the oil line.
If the tank is lower than the stove a lift pump will have to
be utilized.
A clearance of 6 “ (15 cm) must be maintained between
the external/remote tank and the stove.
Technical manual “954” 5
“Le Beffroi” ref. 174 10 54 Installation instructions
200 mm
200 mm
200
mm
200
mm
Figure 4 - Minimum clearances
Figure 5 - Oil supply
1
5
3
6
2
7
1
3
462
7
1- 8 ft maxi
2- At least 9,5 in.
3- Oil tank
4- Filter

2.4. Chimney connector
-The appliance must be as close as possible to the
chimney. Avoid horizontal flue connection pipes which
can dangerously restrain functioning of the appliance.
The connector pipe must be either 24 ga. black painted
or blued steel or 316 grade 20 ga. stainless steel or 1
mm vitreous enamelled steel, with a maximum diameter
of 127 mm (5" O.D.). Single wall pipe may be utilized
being careful to maintain clearances to any combustible
surface.
Once the stove has been properly installed the chimney
draught must be checked with a draught meter.
If the chimney draught is excessive or irregular, a
draught stabilizer (barometric damper) must be
installed to the connector pipe.
2.5. Mounting the levelling feet
Fit the 4 screws and the 4 caps supplied (on the burner)
into each leg of the stove (# 4, p. 13).
2.6. Smoke exit at the top
Figure 6
-Remove the internal baffle (fig. 14, p. 8).
-Fit the blanking plate and the support on the top,
ensuring there is a good seal.
-Fix the sealing rope in the groove on the rear and fit
the flue spigot using the two bolts and washers
supplied, ensuring there is a good seal.
-Replace the internal baffle (fig. 15, p. 8)
2.7. Smoke exit at rear
Figure 7
-Remove the internal baffle (fig. 14, p. 8).
-Set the blanking plate with the flue pipe on the top,
ensuring that it is leaktight.
-Set the ceramic rope in the groove and fixe the flue
collar with 2 screws and ring supplied at rear.
-Reinstall the internal baffle (fig. 15, p. 8).
2.8. Casing assembly
Natural stone : As the stones are easily stained it is
recommended to wear gloves during handling.
Figure 8
➀- Remove the pin of regulator,
➁- Remove the rear panel,
➂- Remove the lateral supports,
➃- Fit the sides panels by sliding and replace the lateral
support (don’t locking). Adjust the side panels with
regard to upright above locking,
Replace the rear panel and the pin.
Figure 9
Natural stones : You must glue, under neath the
stone, the ceramic rope which is supplied.
Enamelled panel : The top neck line must be towards
the back.
6Technical manual “954”
“Le Beffroi” ref. 174 10 54 Installation instructions
1
2
3
4
5
2
6
5
Figure 6 - Smoke exit from top
Figure 7 - Rear flue outlet
2
3
4
1
Figure 8 - Side panels assembly

2.9. Levelling
•It is essential to ensure that the appliance sits level on
the floor. Adjust the levelling feet (# 7, fig. 16, p. 9).
•Use a spirit level across the burner pot to check the
level (fig. 10).
2.10. Oil flow adjustment
The float regulator has been adjusted at the factory and
should not need further adjustment. If the burner does
not work correctly, check possible causes before
readjusting the settings :
-Chimney draught
-Fresh air inlet
-Oil supply.
Low setting (Refer to fig. 11,#4) :
-set the regulating knob on “1" and let the burner run for
a few minutes. The flame must completely cover the
bottom of the burner and the catalyser body must be
glowing red hot.
-if the flame is too small, the stove will soot up quickly ;
increase the flame by turning the setting screw (# 4)
clockwise.
-if the flame is too high, reduce the flame by turning the
setting screw (# 4) counter clockwise.
High setting (Refer to Fig. 11,#5) :
-set the regulating knob on “6" and let the burner run for
a few moments. The flame must be shaped like a cone
and reach the upper part of the door.
-if the flame is too low, increase by turning the set
screw anti-clock-wise.
-if the flame is too high, reduce by turning the set screw
clockwise.
Technical manual “954” 7
“Le Beffroi” ref. 174 10 54 Installation instructions
1
2
3
Figure 9 - Top panel assembly
1- Enamel top plate
2- Natural stone
3- Ceramic rope
Fig. 10- Levelling
Figure 11 - Operating devices
1
2
3
4
5
6
7
1- Adjustment of the draught regulator.
2- Safety lever.
3- Access to regulator filter.
4- Adjustment screw for minimum setting.
5- Adjustment screw for maximum setting.
6- Safety pressure door
7- Vent-pipe (optional).

Please note - Very important : The adjustments of the
float regulator are very sensitive. The hight and the low
setting screws must never be turned more than a 1/4 of
a turn at a time in any direction from their initial setting.
When making any adjustments, allow 3 to 5 minutes
between adjustments to allow burner to stabilize to
previous adjustment before proceeding, if necessary.
2.11. Chimney draught
Once the stove has been properly installed, the
chimney draught must be checked.
The adjustment of the draught will be made with the
barometric damper located at the back of the stove
(# 1, fig. 11).
The reading of the draught must be done once the unit
is hot (minimum 30 minutes of use).
Refer to the specifications p. 3 for minimum draught
requirement on mini setting and on maxi setting.
2.12. Door closing pressure
Figure 13
The closing latch rotates around a pressure screw
positioned cam.
-Loosen pressure screw 1.
-Turn cam 2to desired position.
-Tighten pressure screw 1.
2.13. Pre-utilisation check
Check the condition of the filler seals, that the door
closes correctly, that the window is not damaged, that
the smoke passages are not obstructed by packaging
or removable parts. All removable parts, fuel retainer,
baffle (fig.15), must be correctly installed.
2.14. Mounting mirrors (Optional)
Open the window and position the glasses in the
reflector runner (# 4, fig. 16, p. 9).
2.15. Maintenance of the Chimney
Chimney and chimney connector should be inspected
at least once every three months during the heating
season to determine if a soot build up has occurred. If
soot has accumulated, it should be removed to reduce
the risk of a chimney fire.
8Technical manual “954”
“Le Beffroi” ref. 174 10 54 Installation instructions
Figure 12 - Draught control
Figure 13 - Door closing pressure
2
1

!
"
Figure 14 - Removing the flue baffle

!
"
Figure 15 - Fitting the flue baffle
1- Pressure screw
2- Cam

3. Operating instructions
3.1. Fuel
Warning : Your stove is fitted with a specific float
regulator for a specific oil.
•Fuel oil#2orfuel oil # 1
The fuel oil must be free from any dirt and water which
could disturb the stove in operation.
3.2. Lighting procedure
-Be sure the control knob is to “0" (# 10, fig. 16).
-Turn on oil supply,
-Push down gently on the safety lever (# 2, fig. 11, p. 7).
This will allow the oil to flow into the regulator.
-Open the front door, and remove the catalyser from
burner. Make sure the inside of the pot is clean
thoroughly, and there is no oil accumulation. (fig. 17,
rep. 4, 3 et 2).
-Place 2 tablespoons of methylated spirit or gelled
alcohol in the bottom of the pot. Light the starter gel or
methylated spirit with a fireplace match or long butane
lighter. Place the catalyser back into the burner, being
sure it is centered in the burner. Shut the main door.
-Allow the catalyser to heat approximately 30 to 45 sec.
Turn dail to “1" position.
-Allow 10 to 15 minutes for oil fire and draught to
stabilize. The catalyser should glow red before
adjusting the control knob to a higher setting.
3.3. Operating procedure
•Allow 10 to 15 minutes after lighting to adjust the
control knob to a higher setting, usually between a “2"
and ”4" setting.
When increasing the heat output, move the control
knob only 1 number, allowing 5 minutes between
moves for the flame to re-adjust to new setting.
•If the burner stops during operating, immediatly turn off
the control knob (position “0") and wait until the burner
is completely cool before repeating the lighting
procedure.
3.4. Shutting down
-Set dial to the “0" position (# 10, fig. 16).
-Raise the safety lever of the regulator
(# 2, fig. 11, p. 7).
-Allow the flame to burn out completely before opening
the door.
3.5. Maintenance of the stove
•Every week : operate the de scaling lever (# 9, fig. 16).
-Pull the rod, then push the rod in rotating 360 degrees
two or three times (CAUTION : The rod is HOT).
•Every 3 or 4 months : Clean the burner completely.
-Remove all the parts of the catalyser
(# 2, 3 et 4, fig. 17)
Technical manual “954” 9
“Le Beffroi” ref. 174 10 54 Operating instructions
1
2
3
4
5
6
78
9
1 0
Figure 16 - Operating devices
Figure 17 - Burner
1
2
3
4
5
1- Hot air convector outlet.
2- Plate warmer compartment.
3- Céramics (optional coulor available).
4- Mirrors (optional).
5- Burner.
6- Opening and closing of the windows.
7- Access to the leveling legs.
8- Opening / closing de-scaling.
9- De scaling lever.
10 - Oil contro knob.
1- Air inlet holes
2- Catalyseur ring
3- Catalyser cover
4- Catalyseur body
5- Basic burner

-Using a soft bristle brush (a small clean paint brush),
carefully brush off the catalyser. Loosen any carbon
soot from the bottom of the burner with a putty knife,
and vacuum clean. Ensure that the small air holes in
burner are free of carbon.
•At least once a year / End of heating season :
Clean or replace all the oil filters in the oil supply line
and to change the joint of the de-scaling lever (rep. A,
fig. 18, code 142825) by a professional installer..
To clean the filter of the float regulator :
-set the regulation knob in closed position “0"
(# 10, fig. 16),
-turn off the tankvalve or the valve of the oil supply
ligne,
-raise the safety lever of the float regulator
(# 2, fig. 11, p. 7),
-place a small container (or a small rag) under the
regulator filter opening in order to collect the oil
contained in the regulator,
-remove the filter cover plate located under the
regulator (# 3, fig. 11, p. 7) with a screwdriver,
-remove the tubular filter from the regulator. Clean, if ne
it with oil using a soft brush, never a wire-brush,
-replace the filter in the regulator, install the cover plate
and secure with the screw.
•Clean all the enamelled panels of the stove with a dry
or slighly damp soft cloth.
•Use a soft clean cloth to wipe the front glass when the
unit is running at a low burning rate. When the main
door is opened for cleaning, the flame will be disturb,
and turn to a yellow flame. Clean quickly, but gently.
Close the door, the flame will return to a normal burning
position.
N.B. : The appearance of cracks when burning the
enamelled units is quite usual and tends to disappear
when the appliance is cooling down. It should not be
considered as a defect but rather as a patina of the
enamel which does not affect its quality nor its service
ability.
3.6. Recommendation
•The adjustment of the stove has been made at the
factory and checked by your installer. Any anomaly of
operation should be reported to him at once.
•This room heater is a hight heat producing appliance
and may cause severe burns if touched on the glass
front door, or on top directly over the burner
KEEP CHILDREN AWAY
Do not use for drying wet clothing.
CAUTION : Never light the burner if there is oil in the
burner pot. Clean out oil before lighting.
Racing : An audible fluttering sound is an indication
that there is too much oil in the pot burner and/or a lack
adequate draught.
-turn off oil supply and set the control knob in closed
position “0" (# 10, fig. 16).
-until fire has decreased to proper burn rate.
•Do not overfire : If the stove or chimney connector
starts to glow, you are overfiring.
10 Technical manual “954”
“Le Beffroi” ref. 174 10 54 Operating instructions
A
Figure 18

3.7. Trouble shooting
SYMPTOM PROBLEM -TEST SOLUTION
Flames extinguish during
lighting.
Very cold chimney. No draft
established.
-Leave door ajar until fire has caught.
-Check air supply in the room.
Fire extinguishes once
firestarter has burnt off.
Fuel tank is empty. -Fill tank.
Fuel valve is closed. -Open valve.
Main regulator float not engaging. -De-press the safety lever.
Control knob is set on “0" -Adjust control knob to ”1".
Fire extinguishes during use. Fuel tank is empty. -Fill tank.
Insufficiant draft. -Call your installer.
Flame is excessely large,
smokey and sooty.
Fuel adjustment made too
quickly.
-Return control knob to “1"; wait for normal combustion.
(catalyser should glow red) Wait 5 to 15 minutes
between each adjustment.
Stove burns noisily,
extinguishes and relights
itself.
Burner contains excess fuel. þ-Adjust to lower setting. If problem persists call your
installer.
Insufficient fuel. -Check that the de-scaler, the regulator filter and burner
pot are cleaned.
Fire smokes.Soot build up
noticed. Flame imbalance
Insufficient air supply. -Increase fresh air supply (open door, window; add
make up air supply).
Downdraft or blockage in
chimney.
þ-Check Chimney for Soot build up. clean if necessary.
-Ensure chimney height is sufficient and cap is not
affected by any nearby obstructions.
-Room is in negative pressure. Increase fresh air
supply. Check draft with draft meter and adjust if not to
requirements. See page 5.
Oil flow is too low on 1 setting. þ-Adjust low flow rate while control is set on “1", call your
installer.
Stove is not level. Flame
imbalance.
-Check level. Adjust if necessary.
Catalyser not centered. Uneven
fuel distribution resulting in
secondary air shortage.
-Center catalyser assembly
Insufficient fuel. -Check that the de-scaler, the regulator filter and burner
pot are cleaned.
The draft regulator is blocked in
open position
þ-Unlock the draft regulator.
-Check the regulator adjustment and refit, if necessary.
Coke build up noticed. Excessive air supply. -Adjust draft.
Technical manual “954” 11
“Le Beffroi” ref. 174 10 54 Operating instructions
þ: This sign means that you should
asked for a qualified engineer to do the
work.

4. Spare parts
When ordering spare parts, specify the stove type and
serial number, including the colour index (on the
guarantee or identification plate), the name of the part
and the part number.
Example :
Stove “Le Beffroi”,
Ref. 174 10 54,
Base 300478 EF
12 Technical manual “954”
“Le Beffroi” ref. 174 10 54 Spare parts
Enamel plate
Beige
68 202111 QJ Suppl. top plate ...............01
69 207872 QJ Side panel ..................08
Rouge
68 202111 WA Suppl. top plate ...............01
69 207872 WA Side panel ..................08
Bleu
68 202111 WB Suppl. top plate ...............01
69 207872 WB Side panel ..................08
Natural stone
70 157362 Natural stone ................08
71 157363 Natural stone ................01
72 181607 Ceramic rope ........Ø9,5...0,3m
Optional parts
60 982627 Vent-line ...................01
67 199309 Mirror glass ........1x(260x20) . . 39
Marble
70 149977 Side ......................08
71 149978 Top plate....................01
72 181607 Ceramic rope ................0,3m
Black
70 149979 Side ......................08
71 149980 Top plate....................01
72 181607 Ceramic rope ................0,3m
Beige
70 149981 Side ......................08
71 149982 Top plate....................01
72 181607 Ceramic rope ................0,3m
Gray
1 100917 Axle ............12x20 M7 . . . 01
2 100951 Axle .....................01
3 905326 Burner .............C5.....01
4 109552 Cap .....................04
5 110105 Barometric damper .............01
6 110404 Hinge pin ...........6x30 ....01
7 110405 Hinge pin ...........6x35 ....01
8 119215 Descaler ...................01
9 122204 Winged nut .........diam. 8....02
10 134253 Bushing ...................01
11 134601 Pin ..............2x20 ....01
12 142316 Gasket.............7x3 ...2,04 m
13 142341 Gasket ....................01
14 149087 Handle ....................01
15 149868 Knob .....................01
16 158624 Handle ....................01
17 162576 Descriptive plate ..............01
18 164205 Oil-tight nut .................02
19 165139 Float regulator ...............01
20 179615 Regulator shaft ...............01
21 181606 Ceramic rope ........10x4...1,99 m
22 181607 Ceramic rope ........Ø9,5...2,68 m
23 188807 Glass ....................01
23 199308 Refractory glass .....1x(285x47) . . 01
24 189118 Screw .............Ø10....01
25 205373 Back wall ..................01
26 210501 Clamp ....................01
27 218702 EF Drawer panel ................01
28 221210 Striking plate ................01
29 222550 Flue baffle ..................01
30 226211 Square....................01
31 228620 Square....................02
32 230608 Square....................02
33 230901 Square....................02
34 231711 Square....................03
35 236708 94 Support ...................01
36 239718 60 Support ...................01
37 258406 EF Guide ....................02
38 273214 Hinge ....................01
39 276227 Reflector...................01
40 300478 EF Base .....................01
41 301539 EF Door lock ..................01
42 303301 Bearing ...................01
43 303513 EF Door ash pan ................01
44 303726 EF Blanking plate ................01
45 303829 EF Flue collar ..................01
46 304201 Frame ....................01
47 909401 Sliding door .................01
48 309885 EF Front plate..................01
49 309995 EF Main door ..................01
50 312629 EF support ...................01
51 313815 EF Suppl. front plate ..............01
52 322103 60 Clamp ....................01
53 327204 EF Upright....................08
54 352140 EF Top plate ..................01
55 419003 Stud bolt ...................02
56 446265 Protection plate ...............02
57 604923 EF Firebox shell ................01
58 808001 ED Handle ....................01
59 982626 Feed line tank-regulator ..........01
61 189825 Screw ............M6x5....01
62 199204 Regulator filter ...............01
63 194402 Catalyser body ...............01
64 198205 Catalyser ring ................01
65 194401 Catalyser cover ...............01
66 905322 Burner .............C5.....01
73 104708 Plug .....................01
74 109718 Chain ....................01
75 134749 Pin ..............4x20 ....01
N° Code Description .........Type ....Qty N° Code Description .........Type ....Qty

Technical manual “954” 13
“Le Beffroi” ref. 174 10 54 Spare parts
7 3
7 4
3 1
3 2
3 3
3 4 3 5
3 6
3 7
3 8
3 9
4 0
4 1
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
5 1
5 2
5 3
5 4
5 5
5 6
5 7
5 8
5 9
6 0
6 1
6 2
6 3
6 4
6 5
6 6
6 7
1
2
3
4
5
6
7
8
9
1 0 1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
2 4 2 5
2 6
2 7
2 8
2 9
3 0
9
1 2
1 2
2 2
3 1
3 2
3 3
3 4
3 4
3 7
5 3
5 5
7 1
7 2
6 8
6 9 / 7 0
7 0 / 6 9
7 5

§Guarantee certificate §
§Legal guarantee
The specifications, dimensions and information shown on
our documents are provided for information purposes only
and under no circumstances are binding upon the vendor.
With the aim of constantly improving our equipment, all
modifications considered as necessary by our departments
may be made without notice.
The provisions of the present guarantee certificate are not
excluding or limiting the owner of the equipment’s rights,
concerning the legal guarantee regarding faults or hidden
vices which applies in all circumstances, in the conditions
detailed in articles 1641and following of the civil code, and
in the country in which the equipment was purchased.
§Contractual guarantee
Our equipment is guaranteed against faults and hidden
vices subject to the following conditions:
1) Installation and adjustment of the device by a
professional installer.
2) Observance of the instructions provided in our technical
documents and our installation/adjustment instructions.
3) The installation, use and maintenance of the device
carried out in conformity with the applicable standards
and legislation, and with the indications provided in the
technical instructions accompanying the device.
This guarantee covers the replacement, in our factory, of
parts recognised as being defective from the outset by our
“Guarantee Inspection” Department. Carriage and labour
is at the user’s cost. Moreover, if the repair or replacement
of parts covered by the guarantee is found to be too costly
vis-à-vis the price of the appliance, the decision to replace
or repair the appliance will be taken by the vendor.
Our guarantee is for 2 (two) years for all appliances, with
the exception of closed combustion fireplace and inserts for
which our guarantee is 5 (five) years excluding the
following:
1) Indicator lights, fuses, electrical elements and fans.
2) Parts subject to wear or in contact with high
temperatures namely: soles and burner grills, bottom
plates baffles, ash pans, paintwork and surface
treatments for decorative parts. Also excluded from this
guarantee are seals and windows.
3) Any damage which may result from the use of the
appliance with a fuel other than that stipulated in our
instructions.
4) Damage occurring to parts caused by elements outside
the appliance (down draught, storm damage, damp,
abnormal pressure or vacuum, heat shocks, etc.).
5) Damage to electrical parts caused by plugging in and
using the appliance on a mains system, the voltage of
which (measured at the entrance to the appliance) is
10% above or below the nominal voltage of 220 V.
§Exclusion of liability
In the case of a product manufactured at the client’s
request, under no circumstances may we, as a
subcontractor, be considered liable vis-a-vis the client or
third parties for defects arising from the installation or a
design fault with the item in question.
*Installer/Name and address :
_______________________________________________________________
_______________________________________________________________
(Telephone :
_______________________________________________________________
*Customer/Name and address :
_______________________________________________________________
_______________________________________________________________
Date of installation :
_______________________________________________________________
Model of the appliance : q174 10 54
color : ❑
Serial number :
___ ___ ___ ___ ___ ___
• This certificate has to be completed and kept carefully.
In case of claims, send a copy of this to :
STAUB FONDERIE
BP 73, 59660 MERVILLE, FRANCE.