Franke F3D3S User manual

F3D3 Dual and Single Lane Versions Frozen French
Fry Dispenser
Service Manual

F3D3 Series Service Manual Table of Contents/Section 1.1
Questions? Call Franke Technical Support Group For Your Area. Page 1Copyright 2012 Franke, Inc. All rights reserved.
Section No. Content/Service Operation Issued/Updated
1.1 Table of Contents 11-13-12
1.1.1 Model Identification Guide 5-30-12
1.2.1 Franke Warranty Coverage 5-30-12
1.2.2 Franke Service Contact Information 5-30-12
1.3 F3D3 Series Trouble Shooting Guide 6-6-12
1.4 Display Error Message Guide 5-21-12
1.5 F3D3 Series Parts List & Component Diagrams
1.6 F3D3 Series Electric Schematics 5-24-12
1.7 Control Panel Quick-Guide 5-21-12
Setup, Diagnostic & Programming Instructions
1.8 Customer Level Access Instructions 5-30-12
1.9 Load Cell Calibration Instructions 5-30-12
1.10 Factory Level 1 Setup Access Instructions 5-30-12
1.11 Factory Level 3 Operating Parameter Access & Version Guide 11-13-12
1.11.1 Factory Level 3 Parameter Programming for BL 2.00 11-13-12
1.11.2 Factory Level 3 Parameter Programming for H47C1 11-13-12
1.11.3 Factory Level 3 Parameter Programming for H46P9 11-13-12
1.11.4 Factory Level 3 Display Menu for H46N ONLY 11-13-12
Part Replacement (See Section 4 for Refrigeration Repairs)
2.1 General Service Instructions, Warnings & Tools 5-24-12
2.2 Freezer Door Gasket Replacement 5-21-12
2.3 Automation Assemble [Complete] Replacement 5-22-12
2.4 Door Lift Slide Replacement 5-22-12
2.5 Drum Rotor Motor Replacement 5-22-12
2.6 Drum Rotor/Motor Block & Drive Shaft Replacement
2.7 Door Lift Motor Replacement 5-22-12
2.8 Door [Open] Motor Replacement 5-22-12
2.9 Product Door & Fill Bucket Assembly Replacement 5-22-12
2.10 Load Cell Replacement 5-30-12
2.11 Door-Closing Spring Replacement 5-22-12
2.12 Low Product Sensor Replacement 5-22-12
2.13 Basket Fill Plunger Switch Replacement 11-13-12
2.14 Door-Open Sensor Replacement 5-22-12
2.15 Touch Pad Controls Assembly Replacement 5-29-12
2.16 Main Power ON/OFF Switch Replacement 5-22-12
2.17 Temperature Controller Sensor Cable Replacement 5-22-12
2.18 24-Volt Power Supply Replacement 5-22-12
2.19 Compressor Relay Replacement (DIN Mounted) 5-22-12
2.20 Main PC Control Board Replacement 5-30-12

F3D3 Series Service Manual Table of Contents/Section 1.1
Questions? Call Franke Technical Support Group For Your Area. Page 2Copyright 2012 Franke, Inc. All rights reserved.
Section No. Content/Service Operation Issued/Updated
Part Replacement...Continued
2.21 Main Control Board Chip Replacement 5-29-12
2.22 Door Frame & Freezer Bottom Heater Replacement 5-23-12
2.23 Power Cord Replacement 5-23-12
2.24 Hopper Rotor Replacement 5-23-12
Part or Component Adjustments
3.1 Low Product Sensor Sensitivity Adjustment 5-23-12
3.2 Reverse Door Hinges/Door Swing 5-23-12
3.3 Adjusting Automation Assembly Alignment 5-23-12
3.4 Drum Rotor Motor Adjustment [When making noises] 5-23-12
3.5 Fry Hopper Hanger Alignment 5-23-12
3.6 Activate Backup Temp. Display – Two Lane Models ONLY 5-23-12
Refrigeration System Repair & Replacement
4.0 Propane Refrigeration System SERVICE RESTRICTION 5-23-12
4.1 Basic [Operator] Refrigerator Maintenance 5-23-12
4.2 Replace Condenser Fan Motor 5-24-12
4.3 Replace Start Relay & Replace Start Capacitor 5-24-12
4.4 Check System Pressure & Electronic Leak Detection 5-24-12
4.4.1 Checking for Leaks with Nitrogen Pressure 11-13-12
4.4.2 Cold Wall Evaporator Leak Detection 11-13-12
4.5 Repair System [Refrigerant] Leak 5-24-12
4.6 Replace Thermostatic Expansion Valve & Filter 5-24-12
4.7 Condenser Unit Replacement 5-24-12
Service Bulletins
none
Rev. 2 11-13-12

F3D3 Series Service Manual Model Identification 1.1.1
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Model Identification Guide
Model F3D3
(Shown Hinged-Left)
Model F3D3S
(Shown Hinged-Right)
Lanes & Controls:
Two Lanes
Lanes & Controls:
Single Lane
Unit Width:
711 mm (28”)
Unit Width:
559 mm (22”)
Refrigerant Type
R-404A
Refrigerant Type
R-404A
Model F3D3P
(Shown Hinged-Left)
Model F3D3SP
(Shown Hinged-Right)
Lanes & Controls:
Two Lanes
Lanes & Controls:
Single Lane
Unit Width:
711 mm (28”)
Unit Width:
559 mm (22”)
Refrigerant Type
R-290 PROPANE
Refrigerant Type
R-290 PROPANE

F3D3 Series Service Manual Factory Level 1 Setup Access / 1.10
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012Franke, Inc. All rights reserved.
Setup Access & Resetting
F3D3 Series Fries Dispensers have easy
access to Factory-Level (1) setup and
resetting, using the lane operator interface
touch panel & display. To access:
1) Leave unit plugged in.
2) Turn Main Power Switch ON.
3) Lane power must be OFF. Display will
show current freezer temperature.
To Access Factory Level 1 Setup Parameters:
Step
Action Required
Resulting Display
1
From Standby condition use 3rd touchpad to
enter: 3 3 3 3. [The Entry Code]
Special Mode Select
Cust Fact Exit
2
Press touchpad 2 = Fact(ory)
Factory Access Level
Lev1 Lev3 Exit
3
Press touchpad 1 = Lev1
Low Level Reset ?
Restores all NUM [numbers]
Yes No Exit
4
Press touchpad 1 = Yes
Setup = US
[or actual setup]
Inc Dec Exit
5
Press touchpad 1 = Inc [to scroll through]:
Press touchpad 2 = Dec [to go back up list]:
NOTE: If you press 1 = Inc on Setup =
APMEA, nothing changes. [Press 2 = Dec -
to go back up list.]
Setup = Europe or
Setup = Japan or
Setup = Latin AM [America] or
Setup = Canada or
Setup = APMEA
Inc Dec OK
6
When you press touchpad 3 = OK, screen
goes to:
* Setting Country *
* Specific Params * then:
Setup Complete
Config = US [setup chosen] then:
Calibrate Menu
Begin ?
OK Exit
7A or
Press touchpad 3 = Exit
Shut [appears then screen
goes blank]
7B
Press touchpad 1 = OK [to initiate calibration]
Calibrate Menu
Loadcell = 00XX [Tar Value]
All Clear ?
OK Exit
8
Press touchpad 1 = OK
NOTE: See SM Section LCC
for Load Cell Calibration Instructions.
Rev. 1 6/2012
NOTE: All programming is done using the
three choice buttons labeled: 1, 2 and 3 above.
1
2
3

F3D3 Series Service Manual Factory Level 3 Parameter Access / 1.11
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Parameter Access & Software Version
F3D3 Series Fries Dispensers provide easy access to
Factory Level operating and service diagnostic
parameters using the front operator interface touch
panel & display. To access:
1) Leave unit plugged in.
2) Turn Main Power Switch ON*.
3) Lane power must be OFF. Display will be blank or
show current freezer temperature, depending on
the model and lane.
For To Access Factory Level 3 Parameters:
Step
Action Required
Resulting Display
1
From Standby condition use 3rd touchpad to enter: 3
3 3 3. [The Entry Code]
Special Mode Select
Cust Fact Exit
2
Press touchpad 2 = Fact(ory)
Factory Access Level
Lev1 Lev3 Exit
3
Press touchpad 2 = Lev3
Password ??
Enter Password 0_ _ _
Inc OK Exit
4A
Press touchpad 2 = OK [Icon will move right to next
digit]
Password ??
Enter Password 0 0_ _
Inc OK Exit
4B
Press touchpad 2 = OK [Icon will move right to next
digit]
Password ??
Enter Password 0 0 0_
Inc OK Exit
4C
Press touchpad 2 = OK [Icon will move right to last
digit], then:
Password ??
Enter Password 0 0 0 0
Inc OK Exit
4D
Press touchpad 1 = Inc once, to raise to 1, then:
Password ??
Enter Password 0 0 0 1
Inc OK Exit
5
Press touchpad 2 = OK
Language [first Parameter]
P01 = English
++ -- ->
For F3D3 Software Version To ID Version: Use Table:
Software Version BL 2.00; APP 2.12a
On Lane Display
Parameter Table 1.11.1
Software Version: H47C1
On Chip Label*
Parameter Table 1.11.2
Software Version: H46P9
On Chip Label*
Parameter Table 1.11.3
∗NOTE: The chip version is also displayed briefly during the
startup sequence (after Calibration Values), when the Main
POWER-ON switch is first turned ON. It appears as: Firmware =
H47C1, etc. on the second line. Rev. 1 11/2012
NOTE: All programming is done using the three
choice buttons labeled: 1, 2 and 3 above.
1
2
3

F3D3 Series Service Manual - Factory Lev3 Parameter Access / 1.11.1
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Parameter Access & Programming
F3D3 Series Fries Dispensers provide easy
access to Factory Level operating and
service diagnostic parameters using the
front operator interface touch panel &
display. To access:
1) Leave unit plugged in.
2) Turn Main Power Switch ON.
3) Lane power must be OFF. Display will
be blank or show current freezer
temperature, depending on the lane.
To Access Factory Level 3 Parameters:
Step
Action Required
Resulting Display
1
From Standby condition use 3rd touchpad to
enter: 3 3 3 3. [The Entry Code]
Special Mode Select
Cust Fact Exit
2
Press touchpad 2 = Fact(ory)
Factory Access Level
Lev1 Lev3 Exit
3
Press touchpad 2 = Lev3
Password ??
Enter Password 0_ _ _
Inc OK Exit
4A
Press touchpad 2 = OK [Icon will move right to
next digit]
Password ??
Enter Password 0 0_ _
Inc OK Exit
4B
Press touchpad 2 = OK [Icon will move right to
next digit]
Password ??
Enter Password 0 0 0_
Inc OK Exit
4C
Press touchpad 2 = OK [Icon will move right to
last digit], then:
Password ??
Enter Password 0 0 0 0
Inc OK Exit
4D
Press touchpad 1 = Inc once, to raise to 1,
then:
Password ??
Enter Password 0 0 0 1
Inc OK Exit
5
Press touchpad 2 = OK
Language [first Parameter]
P01 = English
++ -- ->
See Parameter Spreadsheet for P-numbers, functions & default settings.
NOTE Software Codes and exceptions that apply.
Notes:
Command Key: ++ to scroll up; -- to scroll down; -> to move flashing
underscore __ under next value; == to accept or OK value or setting
P02
Set Point
Example:
Press 1 = ++ to increase temp. value [-0004]
Press 2 = -- to decrease temp. value [- 0006]
Press 3 = == to accept (new) setting
Set Point [Refrigerator temp.]
P02 = -0005F
++ -- ==
Rev. 16/2012
NOTE: All programming is done using the
three choice buttons labeled: 1, 2 and 3 above.
1
2
3

F3D3 Series Service Manual Factory Level 3 Parameter Access / 1.11.1
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Factory Level 3 - Parameter Guide – Page 1
[For Latest Models with BL 2.00; APP 2.12a Chip Software1)]
Parameter
Range
Unit
3)
Factory
Default
Notes
Country Exceptions
GM Exceptions
No.
Name
Low
High
US
EU
JP
LA
CN
AP
EU-B
US-
GM
CAN-
GM
Other
-GM
EU-Y
P01
Language
1
5
1
1=English, 2=Deutsch,
3=Espanola, 4=Francais,
5=French/English (Canada)
1
1
1
1
5
1
1
1
5
1
1
P02
Set Point
-50
20
Deg F
-5
Temperature set point
P03
Offset
-30 30 Deg F 8 Temperature offset from sensor
P04
High Alarm Set
Point
-100
50
Deg F
40
Temperature that triggers a high
alarm (LON Models only)
P05
High Alarm (Start
Up) Delay
1
300
(M)
minutes
100
Time to wait after high alarm
signal, until message appears
P06
High Alarm Dwell
1
300
(M)
minutes
60
Temperature must remain (dwell)
for this time
P07
Hysteresis
0.5
5
Deg F
1.0
Used in temperature control
P09
Compressor Off
Time
1
200
(S)
seconds
120
Minimum time the compressor
must be off before restarting.
P10
Down Shift LM
1
19
20=off
(M)
minutes
4
Time for a size downshift from
large to medium. 20 = Off
4
7
4
4
4
4
Off
Off
Off
Off
10
P11
Down Shift M1S
1
19
(20= off)
(M )
minutes
20 (off)
Time for an initial size downshift
from medium to small. 20 = Off
Off
3
Off
Off
Off
Off
Off
Off
Off
Off
5
P12 Down Shift M2S 1 19
(20= off) (M) minutes 20 (off)
Time for subsequent size
downshift from medium to small.
20 = Off
Off
7
Off
Off
Off
Off
Off
Off
Off
Off
10
P13
Drum (Motor)
Torq(ue)
Thres(hold)
10
1500
750
Motor stops if threshold
exceeded. Approx 250
counts/amp of motor current.
P14
Door (Motor)
Torq(ue)
Thres(hold)
10
1500
750
Motor stops if threshold
exceeded. Approx 250
counts/amp of motor current.
P15
Lift (Motor)
Torq(ue)
Thres(hold) 10 1500 750
Motor stops if threshold
exceeded. Approx 250
counts/motor current.
P16
Basket In Time
10
1500
mS
150
Time the basket must remain in
to trigger a dispense cycle
150
350
150
150
150
150
150
150
150
150
150
NOTES: 1) No Main Board Chip Label. Software Vers(ion): BL 2.00; APP 2.12a appears on Lane Display.

F3D3 Series Service Manual Factory Level 3 Parameter Access / 1.11.1
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Factory Level 3 - Parameter Guide – Page 2
[For Latest Models with BL 2.00; APP 2.12a Chip Software1)]
Range
Unit
3)
Factory
Default
Notes
Country Exceptions
2)
GM Exceptions
No.
Name
Low
High
US
EU
JP
LA
CN
AP
EU-B
US-
GM
CAN-
GM
Other
-GM
EU-Y
P17
Basket Out Time
10
1500
mS
50
Time the basket must remain
out before enabling dispense
P18
Low Product
Enable
Off
On
On
Prevents Low Product Warning
being displayed.
P19
Hi Accuracy
Enable
Off
On
Off
Enables high accuracy (but
slower) dispense for Japan.
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
P21
Large Fill Pct
50 100 % 90 Reserved - Do not adjust.
P22
Medium Fill Pct
50
100
%
89
Reserved - Do not adjust.
P23 Small Fill Pct 50 100 % 88 Reserved - Do not adjust.
P26
Dual Language
Toggle Rate
1
4
3
If Dual Language is enabled,
this sets toggle rate: (1 = Off,
2 = Slow, 3 = Med, 4 = Fast)
P27
Display Units
C
F
F
Temperature Display Units
Celsius or Fahrenheit
F
C
C
C
C
C
C
F
C
C
C
P28
Backdoor Type
English
Numeric
English
Displays numeric codes with
English or numeric codes only
P29
Medium (Load)
Factor 25 100 % 67 Weight of medium load as
percent of large load 67 67 67 67 67 67 80 67 67 67
75
P30
Small (Load)
Factor
25
100
%
50
Weight of small load as percent
of large load
50
50
50
50
50
50
67
50
50
50
34
P31
Part Number
15 characters maximum. 1
st
must be 0-9 or F. 2
nd
must be 0-9, S, ‘.’ or ‘-‘. All others: 0-9, ‘-‘ or ‘.’
P32
Serial Number
15 characters maximum. All characters: 0-9 or ‘-‘
P99
Exit Exits Level 3, if Entered
NOTES: 1) No Main Board Chip Label. Software Vers(ion): BL 2.00; APP 2.12a appears on Lane
Display. [How is this called up?]
2) Country Exceptions Abbreviations: US = North America; EU = Europe; JP = Japan; LA = Latin
America (South & Central); CN = Canada; AP = Asia, Pacific, Middle East & Australia
3) Unit Abbreviation: mS = Milliseconds

F3D3 Series Service Manual - Factory Lev3 Parameter Access / 1.11.2
Questions? Call Franke Technical Support Group For Your Area. Copyright 2012 Franke, Inc. All rights reserved.
Parameter Access & Programming
F3D3 Series Fries Dispensers provide easy
access to Factory Level operating and
service diagnostic parameters using the
front operator interface touch panel &
display. To access:
1) Leave unit plugged in.
2) Turn Main Power Switch ON.
3) Lane power must be OFF. Display will
be blank or show current freezer
temperature, depending on the lane.
To Access Factory Level 3 Parameters:
Step
Action Required
Resulting Display
1
From Standby condition use 3rd touchpad to
enter: 3 3 3 3. [The Entry Code]
Special Mode Select
Cust Fact Exit
2
Press touchpad 2 = Fact(ory)
Factory Access Level
Lev1 Lev3 Exit
3
Press touchpad 2 = Lev3
Password ??
Enter Password 0_ _ _
Inc OK Exit
4A
Press touchpad 2 = OK [Icon will move right to
next digit]
Password ??
Enter Password 0 0_ _
Inc OK Exit
4B
Press touchpad 2 = OK [Icon will move right to
next digit]
Password ??
Enter Password 0 0 0_
Inc OK Exit
4C
Press touchpad 2 = OK [Icon will move right to
last digit], then:
Password ??
Enter Password 0 0 0 0
Inc OK Exit
4D
Press touchpad 1 = Inc once, to raise to 1,
then:
Password ??
Enter Password 0 0 0 1
Inc OK Exit
5
Press touchpad 2 = OK
Language [first Parameter]
P01 = English
++ -- ->
See Parameter Spreadsheet for P-numbers, functions & default settings.
NOTE Software Codes and exceptions that apply.
Notes:
Command Key: ++ to scroll up; -- to scroll down; -> to move flashing
underscore __ under next value; == to accept or OK value or setting
P02
Set Point
Example:
Press 1 = ++ to increase temp. value [-0004]
Press 2 = -- to decrease temp. value [- 0006]
Press 3 = == to accept (new) setting
Set Point [Refrigerator temp.]
P02 = -0005F
++ -- ==
Rev. 111/2012
NOTE: All programming is done using the
three choice buttons labeled: 1, 2 and 3 above.
1
2
3