Franke AQCT0064 User manual

Installation and operating instructions Istruzioni per il montaggio e l’uso
Notice de montage et de mise en service Montage- en bedrijfsinstructies
Instrucciones de montaje y uso
ZMI_001_2030020357-AQCT0064_#SALL_#AQU_#V3.fm / 27.01.14
EA-Nr.: 7612982218927
FAR-Best.-Nr.: 2030020357
AQCT0064
EA-Nr.: 7612982218934
FAR-Best.-Nr.: 2030020359
AQCT0065
EA-Nr.: 7612982235368
FAR-Best.-Nr.: 2030033327
AQCT0103
DE
EN
FR
ES
IT
NL

Inhaltsverzeichnis35_01.fm
- 2 -
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 19
Les graphiques sont disponibles dans la notice de montage et de
mise en service allemande.
...................................................................................... 37
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 53
Per le grafiche fare riferimento alle Istruzioni per il montaggio e
l’uso in tedesco.
...................................................................................... 69
De tekeningen kunt u in de Duitse montage- en bedrijfsinst-
ructies vinden.
EN
FR
ES
IT
NL

- 3 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
0English
AQUACONTACT - shower panel made of stainless steel with 6 V DC thermostat
AQCT0064
AQCT0065 ................. with integrated shower gel tray
AQCT0103 ................. with automatic shower pipe evacuation
Please refer to the graphics in the German installation and operating instructions.
0Table of contents
1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Spray pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly, function and commissioning
11. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13. Thermal disinfection -manual- . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. Thermal disinfection -automatic- . . . . . . . . . . . . . . . . . . . . . . . . . 10
15. Setting the scald protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
16. Adjusting the flow time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
17. Adjusting the range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
18. Hygiene flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
19. Adjusting the cleaning switch-off . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance
20. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
21. Cleaning the shower head faceplate . . . . . . . . . . . . . . . . . . . . . . 14
22. Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
23. Replacing the solenoid valve cartridge. . . . . . . . . . . . . . . . . . . . . 14
24. Replace the thermal element . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
25. Replacing the flow rate regulator . . . . . . . . . . . . . . . . . . . . . . . . . 15
26. Replacing the non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
27. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
28. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EN

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 4 -
1. Abbreviations and units
2. Key
Warning!
Failure to observe can result in bodily injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimal handling of the product.
3. Warranty
Liability is accepted in accordance with the General Terms and Conditions of
Business and Supply.
Use only genuine spare parts!
DN Nominal diameter in mm
RCD Residual current protective device,
Earth leakage circuit breaker
SELV Safety extra low voltage
EA-Nr. European article number
FAR-Best.-Nr. Franke Aquarotter order number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

- 5 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
4. Important notes
• Installation, commissioning and maintenance are to be performed only by a
qualified expert in accordance with the instructions provided, legal requirements
and recognised engineering standards.
• All technical connection regulations specified by the local water and electricity
supply companies must be observed.
• The battery compartment with battery or power supply with extension cable must
be ordered separately (see Accessories, Chapter 28).
• All work must be carried out in a de-energised state.
• We reserve the right to make changes.
5. Application
AQUACONTACT - a stainless steel shower panel for wall mounting with electronic
time control for battery or mains operation, with DN15 thermostat battery. For
connection to hot and cold water supply. 30 second flow time.
With a device for an optional bypass solenoid valve cartridge for carrying out thermal
disinfection, with the option of manual thermal disinfection.
With integrated hygiene flush (24h after last actuation, for 10s). Functions which can
be activated via reflection code on sensor: Activation/deactivation of hygiene flush
and cleaning switch-off (3 min.).
Additional functions via optional remote control
– Adjustment of flow and interval times for hygiene flush
– Switch from time control to body reflection, maximum flow time of 300 seconds
– Program-controlled thermal disinfection with safety switch-off
6. Technical specifications
Minimum flow pressure: 1.0 bar
Recommended flow pressure: 1-5 bar
Maximum operating pressure: 10 bar
Calculated flow rate: 0.15 l/s 0.15 l/s
Volumetric flow:
Fitting: 0.20 l/s at a flow pressure of 3 bar
Bypass: 0.06 l/s at a flow pressure of 3 bar
Flow duration: 30 s
Operating voltage: 6 V DC
Power consumption: 1.5 W
Protection class: IP 67

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 6 -
7. Scope of delivery
8. Dimensions
9. Installation example
10. Spray pattern
11. Assembly
Warning!
Only operate the fitting with non-return valves and the specified filters.
Failure to observe this instruction can result in an increased germ load in the
drinking water and thus pose a health or mortality risk.
Warning!
• Operate the product only with safety extra low voltage (SELV). The components
must not be earthed.
• Protect the power supply with a residual current circuit breaker (RCD).
Failure to observe this instruction can result in death or material damage due to
electric shock or fire, for example.
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
Quantity Name
1 Stainless steel shower panel with:
thermostat, AQUACONTACT sensor, solenoid
valve cartridge, lockable water volume regulators,
connection pipes and AQUAJET Slimline shower
head
4 Wood screw, wall plug
1 Suspension rail
2 Connection bracket
1 0.15 l/s flow rate regulator
1 Installation and operating instructions

- 7 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
☞Depending on the composition of the wall, special wall plugs may have to be used
(to be provided by the customer).
Fig. A: Water connection from above
Fig. B: Water connection from the rear
11.1 Only for water connection from the rear: Install the connection brackets (a) leak-tight.
11.2 Screw in the water volume regulators (b) leak-tight.
11.3 Align the water volume regulators so that the locking screw and operating element
are freely accessible.
11.4 For a shower head height of 2.10 m to 2.30 m, mark drill holes for installation at a
height (c) of 2.14 m to 2.34 m from the top of the finished floor.
11.5 Drill holes in accordance with these markings.
11.6 Insert the wall plugs.
11.7 Screw on the suspension rail.
11.8 Suspend the shower panel.
11.9 Mark the remaining drill holes.
11.10 Remove the shower panel.
11.11 Drill holes in accordance with these markings.
Insert the wall plugs.
☞The battery compartment or power supply and extension cable are not part of the
scope of delivery (see Accessories, Chapter 28).
☞If you are using a wall-mounted power supply unit, it must be installed around 3 m
away from the shower.
11.12 Connect the AQUACONTACT sensor (d) to
– a battery compartment (e)
or
– a wall-mounted power supply unit (f).
☞If the battery charge state is low, the LED flashes in a 20 second cycle.
11.13 Remove the protective film from the shower panel.
11.14 Seal the shower panel (e.g. with Chromol, not part of the scope of delivery, see
Accessories, Chapter 28).
11.15 Only for water connection from the rear: Prioritise work steps 11.17 to 11.19.
11.16 Mount the shower panel on the suspension rail and screw tight.
11.17 Establish the water connections.
11.18 Open the water volume regulators using an Allen key.
a: closed
b: open
11.19 Check the water connections for leaks.

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 8 -
12. Function
☞You can switch between time control and body reflection using the remote control
(not in the scope of delivery; see Accessories, Chapter 28)
Time control
Trigger the flow of water
12.1 Hold your hand near the sensor.
• The water will flow.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again.
☞The flow duration is factory-set to 30 seconds.
Body reflection
Trigger the flow of water
12.2 Hold your hand near the sensor.
• The water will flow.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again
or
– after leaving the sensor range.
Temperature selection

- 9 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
13. Thermal disinfection -manual-
This shower fitting offers thermal disinfection to reduce the risk of a legionella
infection.
The thermal disinfection process is triggered by overturning the thermostat.
Warning!
Personal protective measures (scald protection) must be implemented for the
duration of the thermal disinfection. This might include cordoning off the shower
facilities.
Failure to observe this instruction can result in injuries due to scalding.
The operator is responsible for the execution, monitoring, and logging (room,
tapping point, date, time, temperature and duration).
The manufacturer does not accept any liability for claims by third parties relating to
the improper execution of thermal disinfection on the part of the operator.
The thermostat fitting has been prepared to carry out a thermal disinfection process
when the thermostat is overturned. The thermostat fitting can be manually thermally
disinfected (flushed with water at a temperature of 70°C) by unlocking the covered
stop on the temperature selector.
13.1 A shower pipe (e.g. HT pipe, di= 100 mm) should be placed under the shower head
to deflect the hot water to avoid scalding during the thermal disinfection process.
13.2 Turn the temperature selector (a) to the hot water stop.
13.3 Use the Allen key to push in the stop.
13.4 Turn the temperature selector (a) in an anti-clockwise direction up to the stop.
13.5 Trigger the fitting.
13.6 Measure the hot water temperature.
13.7 If the hot water temperature is > 70°C, the fitting should be flushed for at least 3
minutes. Trigger the fitting several times for this purpose.
☞The thermal disinfection process must be recorded (room, tapping point, date, time,
temperature, duration).
13.8 Turn the temperature selector (a) clockwise until it engages.
Caution!
The temperature selector (a) may not be turned beyond the stop in an anti-
clockwise direction.
13.9 Test the limit stop.
13.10 Trigger the fitting to drain the remaining hot water.
13.11 Measure the water temperature. The maximum water temperature may not exceed
40°C (see Chapter 15.).
☞Once thermal disinfection has been completed, the scald protector does not need to
be reset.

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 10 -
14. Thermal disinfection -automatic-
This fitting offers thermal disinfection to reduce the risk of a legionella infection.
Caution!
The directions in the Thermal Disinfection Planning Aid (01805618) must be
adhered to.
Warning!
Personal protective measures (scald protection) must be implemented for the
duration of the thermal disinfection. This might include cordoning off the shower
facilities.
Failure to observe this instruction can result in injuries due to scalding.
The operator is responsible for the execution, monitoring, and logging (room,
tapping point, date, time, temperature and duration).
The manufacturer does not accept any liability for claims by third parties relating to
the improper execution of thermal disinfection on the part of the operator.
☞At the factory, the thermal disinfection function is set so that the fitting cools down for
1 minute after a 5 minute application time.
☞Thermal disinfection can only be triggered using the remote control.
You can adjust the thermal disinfection parameters using the remote control (not part
of the scope of delivery, see Chapter 28.).
An application time of 3, 5, 10, 15, or 20 minutes can be chosen for the thermal
disinfection process. During the application time, water flows without interruption for
2 minutes; the water then flows in pulses until the end of the application time (water
and energy saving function). The cooling time can be set to 0, 1, 3, 5, or 10 minutes.
Required accessories
Bypass solenoid valve cartridge . . . . 2000109499

- 11 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
15. Setting the scald protector
Warning!
If the hot water supply temperature is above 45°C, the scald protector should be set.
Failure to observe this instruction can result in injuries due to scalding.
☞The scald protector (hot water stop) has been set to 38°C at the factory. Set the
system-specific parameters before use.
15.1 Remove the cover platelet (d).
15.2 Release the screw (c) with its disk.
15.3 Remove the temperature selector (b).
15.4 Remove the stop ring (a).
15.5 Trigger the fitting.
15.6 The temperature is freely selectable:
Set the maximum water temperature on the adjustment nut (e), e.g. to 40 °C.
15.7 Mount the stop ring (a) in such a way that the marking (f) is centred below the
markings (g) for the rosette.
☞Important!
Mount the temperature selector (a) in such a way that the stop is flush against the
stop ring crosspiece.
15.8 Slide the temperature selector (a) onto the stop ring (b).
15.9 Attach the temperature selector (m) and its screw (n) and disk to the fitting.
tightening torque: 1 Nm
15.10 Fit the cover platelet (w).
16. Adjusting the flow time
You can adjust the flow time from 10 seconds to 5 minutes seconds using the
remote control (not part of the scope of delivery; see Accessories, Chapter 28).
17. Adjusting the range
You can adjust the range for body reflection using the remote control (not part of the
scope of delivery; see Accessories, Chapter 28).

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 12 -
18. Hygiene flush
☞At the factory, the hygiene flush function is set so that water flows for 10 seconds 24
hours after the flush was last activated.
You can adjust the hygiene flush parameters using the remote control (not part of the
scope of delivery; see Accessories, Chapter 28).
You can choose an interval of 0, 8, 24, 48, or 72 hours for the hygiene flush function
(0 = hygiene flush deactivated). You can adjust the flow time from 10 seconds to 10
minutes.
Display of hygiene flush on fitting
18.1 Hold your hand around 10 cm from the sensor for 3 seconds.
18.2 Between the 1st and 2nd flashing of the LED, remove your hand from the sensor.
• Hygiene flush active: The LED flashes quickly 4 times.
• Hygiene flush inactive: The LED flashes slowly twice.
Activation/deactivation of hygiene flush on the fitting
18.3 Hold your hand around 10 cm from the sensor for 3 seconds.
18.4 Between the 6th and 8th flashing of the LED, remove your hand from the range of
the sensor.
• The LED does not flash.
18.5 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.
18.6 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The LED flashes quickly 4 times. The hygiene flush is active.
or
• The LED flashes slowly twice. The hygiene flush is deactivated.
19. Adjusting the cleaning switch-off
You can activate the cleaning switch-off with the remote control (not part of the
scope of delivery, see Accessories, Chapter 28) or directly on the fitting.
Cleaning switch-off on the fitting
19.1 Hold your hand around 10 cm from the sensor for 3 seconds.
19.2 Between the 3rd and 5th flashing of the LED, remove your hand from the range of
the sensor.
• The LED does not flash.
19.3 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.

- 13 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
19.4 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The fitting will be switched off for 3 minutes.
• The LED flashes in a 10 second cycle.
☞If you hold your hand around 10 cm from the sensor for at least 3 seconds, the fitting
will be reactivated before the 3 minutes has expired.
20. Maintenance and care
The fitting must be checked and maintained at regular intervals, depending on the
water quality and in accordance with the local conditions and rules and regulations
applicable at the site.
Maintain the following components:
• Shower head (see Chapter 21.)
• Filters (see Chapter 22.)
• Non-return valve (see Chapter 26.)
Use suitable cleaning agents which do not attack the fitting in a proper manner and
rinse with water after use. High-pressure cleaners must not be used for cleaning.
Removing the shower panel
For some maintenance tasks, the shower panel must be removed.
Caution!
Do not allow the shower panel to hang by the connecting hoses.
Water connection from above:
20.1 Close the water volume regulators.
a: closed
b: open
20.2 Trigger the fitting.
20.3 Disconnect the water supply.
20.4 Release the screws on the shower panel.
20.5 Unhook the shower panel.
Water connection from rear:
20.6 Release the screws on the shower panel.
20.7 Unhook the shower panel.
20.8 Close the water volume regulators (see Work step 20.1).
20.9 Trigger the fitting.
20.10 Disconnect the water supply.

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 14 -
21. Cleaning the shower head faceplate
21.1 Release the screw using an Allen key.
21.2 With a screwdriver, carefully lever out the spray faceplate.
21.3 Clean the shower head faceplate.
21.4 Reassemble in reverse order.
22. Replacing the filters
Water volume regulator filters
22.1 Remove the shower panel(see Chapter 20.).
22.2 Unscrew the locking screws (a) on the water volume regulators.
22.3 Replace the filters (b).
☞Important!
Note the installation position of the filters.
22.4 Reassemble in reverse order.
Solenoid valve cartridge filter
22.5 Remove the solenoid valve cartridge (see Chapter 23.).
22.6 Use flat-nosed pliers to remove the filter (c).
22.7 Replace the filter.
☞Important!
Note the installation position. The crosspiece of the filter may not be on top of the
flow hole.
22.8 Reassemble in reverse order.
23. Replacing the solenoid valve cartridge
23.1 Remove the shower panel (see Chapter 20.).
23.2 Disconnect the cable connection between the solenoid valve cartridge and the
AQUACONTACT sensor.
23.3 Loosen the screws (a).
23.4 Remove and replace the solenoid valve cartridge (b).
☞Important!
The solenoid valve must be connected before the power supply is connected.
23.5 Reassemble in reverse order.

- 15 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
24. Replace the thermal element
Warning!
Set the scald protection after installing the fitting or removing the thermal element.
Failure to observe this instruction can result in injuries due to scalding.
24.1 Close the water volume regulators (see Work step 11.18).
24.2 Trigger the fitting.
24.3 Remove the temperature selector (see Chapter 15.).
24.4 Remove the screw (b)
Caution!
Apply the pliers to the area with the largest diameter (a) behind the small sprocket
wheel.
If the sprocket wheel is damaged, the temperature selector cannot be installed.
24.5 Use pliers to remove the thermal element (c).
☞Important!
Note the installation position of the thermal element.
24.6 Reassemble in reverse order.
24.7 Set the scald protection (see Chapter 15.).
25. Replacing the flow rate regulator
25.1 Release the grub screw with an Allen key.
25.2 Pull the shower head out of the connection pipe.
25.3 Remove the locking ring on the inside using appropriate pliers for locking rings.
25.4 Pull out the flow rate regulator using flat-nosed pliers.
25.5 Replace the flow rate regulator. Observe the table.
☞Important!
Note the installation position of the flow rate regulator. The struts must point towards
the shower head.
25.6 Insert the flow rate regulator and secure with the locking ring.
a: Struts
b: Direction of flow
25.7 Reassemble in reverse order.
Flow rate Flow rate regulator
0.15 l/s (orange) FAR-Best.-Nr. 2000104782
0.20 l/s (red) FAR-Best.-Nr. 2000104783

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 16 -
26. Replacing the non-return valve
Warning!
All non-return valves must be replaced at the same time.
Failure to observe this instruction can result in an increased germ load in the
drinking water and thus pose a health or mortality risk.
26.1 Remove the shower panel (see Chapter 20.).
26.2 Loosen the cap nuts (b).
26.3 Remove the hoses (a).
26.4 Remove the existing seals (c).
26.5 Remove the locking ring (d) on the inside using appropriate pliers for locking rings.
26.6 Pull the non-return valve (e) out of the function block using a special tool
(FAR-Best.-Nr. 2000105636).
26.7 Remove the lock (f) using an Allen key.
26.8 Remove the spacer (g).
26.9 Pull the non-return valve (h) out of the function block using a special tool
(FAR-Best.-Nr. 2000105636).
Caution!
Note the installation position of the non-return valves.
26.10 Reassemble in reverse order.
27. Troubleshooting
Fault Cause Remedy
Water does not flow – Water supply interrupted ➯Restore it
– Water volume regulator closed ➯Open it
– Power supply interrupted ➯Restore it
– Solenoid valve cartridge faulty ➯Replace it
– Sensor faulty ➯Replace it
– Dirty filters/non-return valves ➯Clean and
replace if
necessary
Flow time too short or
too long
– Incorrect flow time setting ➯Set it
– Shower head blocked with scale ➯Cleaning

- 17 -
ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
If you cannot rectify a fault or if it is not in the list, please contact our customer
service department!
Water flows conti-
nuously
– Solenoid valve cartridge faulty ➯Replace it
– Flow rate regulator in shower head
blocked with scale
➯Clean and
replace if
necessary
Water too hot – Scald protection set incorrectly ➯Set it
– Thermal element faulty ➯Replace it
Water too cold – Scald protection set incorrectly ➯Set it
– Hot water flow blocked ➯Open it
– Dirty filters/non-return valves ➯Clean and
replace if
necessary
– Hot water supply pressure too low ➯Check it
– Hot water temperature too low ➯Increase it
– Thermal element faulty ➯Replace it
Water volume too low – Water volume regulator not fully open ➯Open it
– Shower head blocked with scale ➯Clean it
– Dirty filters/non-return valves ➯Clean and
replace if
necessary
– Supply pressure too low ➯Check it
Thermostat controls
unevenly
– Flow rate regulator in shower head
blocked with scale
➯Clean and
replace if
necessary
– Thermal element dirty ➯Clean it
Fault Cause Remedy

ZMI_001_2030020357-AQCT0064_#SEN_#AQU_#V3.fm
- 18 -
28. Spare parts
Description Order No.
1 Cover platelet . . . . . . . . . . . . . . . . . . 2030003258
2 Temperature selector . . . . . . . . . . . . 2030003254
3 Temperature stop . . . . . . . . . . . . . . . 2030003296
4 Thermal element. . . . . . . . . . . . . . . . 2030003300
5 AQUACONTACT sensor. . . . . . . . . . 2030004622
6 Push-on rosette. . . . . . . . . . . . . . . . . 2030022726
7 Lockable
water volume regulator . . . . . . . . 2000104885
8 Shower head spares kit . . . . . . . . . . 2000104849
9 Flow rate regulator
0.15 l/s (9 l/min) . . . . . . . . . . . . . 2000104782
0.20 l/s (12 l/min) . . . . . . . . . . . . 2000104783
10 Solenoid valve cartridge . . . . . . . . . . 2000109499
11 Mounting kit consisting of:
Filters
Non-return valve
O-rings
Seals
Locking rings . . . . . . . . . . . . . . . . 2000104777
Spare parts kit for DN 15 consisting of:
Rubber parts
Compression spring
Locking ring . . . . . . . . . . . . . . . . . 2000104804
Connecting pipe
Hot/cold . . . . . . . . . . . . . . . . . . . . 2000105647
Mixed water . . . . . . . . . . . . . . . . . 2000105648
Accessories Order No.
Battery compartment with battery . . . 2000109466
6 V lithium battery,
Type CRP2. . . . . . . . . . . . . . . . . . 2000104846
Wall-mounted power supply . . . . . . . 2000109417
Extension cable for wall-mounted power supplies
3 m. . . . . . . . . . . . . . . . . . . . . . . . 2000101456
10 m. . . . . . . . . . . . . . . . . . . . . . . 2000101457
Power supply . . . . . . . . . . . . . . . . . . 2030039477
Extension cable for power supplies
3 m. . . . . . . . . . . . . . . . . . . . . . . . 2030010982
Remote control . . . . . . . . . . . . . . . . . 2000101087
Soap dish
1)
. . . . . . . . . . . . . . . . . . . . 2000100978
CHROMOL 0.5 l stainless steel
polish. . . . . . . . . . . . . . . . . . . . . . . . . 2000105091
Stainless steel maintenance set complete
CHROMOL 0.5 l
Abrasive sponge, coarse
Abrasive sponge, fine . . . . . . . . . 2000109019
1)
with mounting accessories

- 19 -
ZMI_001_2030020357-AQCT0064_#SFR_#AQU_#V3.fm
0Français
AQUACONTACT - Panneau de douche en acier inoxydable avec thermostat, 6 V DC
AQCT0064
AQCT0065 ................. avec support pour gel de douche intégré
AQCT0103 ................. avec purge automatique des tuyaux de la douche
Les graphiques figurent dans la notice de montage et de mise en service allemande.
0Table des matières
1. Abréviations et unités . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2. Pictogrammes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3. Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4. Remarques importantes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Description du produit
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6. Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7. Contenu de la livraison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9. Exemple d'installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10. Schéma du jet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Montage, fonctionnement et mise en service
11. Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12. Fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
13. Désinfection thermique -manuelle-. . . . . . . . . . . . . . . . . . . . . . . . 26
14. Désinfection thermique -automatique- . . . . . . . . . . . . . . . . . . . . . 27
15. Régler la protection contre les brûlures . . . . . . . . . . . . . . . . . . . . 28
16. Réglage de la durée d'écoulement. . . . . . . . . . . . . . . . . . . . . . . . 28
17. Réglage de la portée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
18. Rinçage hygiénique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
19. Régler l'arrêt du nettoyage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Entretien
20. Maintenance et entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
21. Nettoyage de la base de la pomme de douche . . . . . . . . . . . . . . 31
22. Remplacement des filtres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
23. Remplacement de la cartouche d'électrovanne . . . . . . . . . . . . . . 32
24. Remplacer le thermocouple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
25. Remplacement du régulateur de débit d'eau . . . . . . . . . . . . . . . . 32
26. Remplacement des clapets de non-retour . . . . . . . . . . . . . . . . . . 33
27. Dépannage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
28. Pièces de rechange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
FR

ZMI_001_2030020357-AQCT0064_#SFR_#AQU_#V3.fm
- 20 -
1. Abréviations et unités
2. Pictogrammes
Avertissement !
Le non-respect des consignes est susceptible de présenter un danger de mort ou de
provoquer des blessures.
Attention !
Le non-respect des consignes est susceptible de provoquer des dommages
matériels.
☞Important !
Le non-respect des consignes est susceptible de provoquer des dysfonctionne-
ments sur le produit.
☞Informations utiles pour une utilisation optimale du produit.
3. Garantie
La responsabilité est conforme à celle décrite dans les conditions générales de
vente et de livraison.
Utiliser exclusivement des pièces de rechange d'origine !
DN Diamètre nominal en mm
RCD Residual Current Protective Device,
interrupteur de protection contre les courants de
court-circuit
SELV Safety Extra Low Voltage, très basse tension de
sécurité
EA-Nr. Numéro d'article européen
FAR-Best.-Nr. Référence de commande Franke Aquarotter
Conversion 1 mm = 0,03937 pouce
1 pouce = 25,4 mm
Sur les graphiques, toutes les longueurs sont exprimées en mm.