Franke AQRE432 User manual

Installation and operating instructions Istruzioni per il montaggio e l’uso
Notice de montage et de mise en service Montage- en bedrijfsinstructies
Instrucciones de montaje y uso Montaż i instrukcja obsługi
18-05.306e_Exp.fm/13.10.11
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982102257
FAR-Best.-Nr.: 5526 11 24-F
AQRE432
EA-Nr.: 7612982102264
FAR-Best.-Nr.: 5526 12 24-F
AQRE433

2
Inhaltsverzeichnis06.fm
...............................................................3
Please refer to the graphics in the German Instal-
lation and Operating Instructions.
...............................................................12
Les graphiques sont disponibles dans la notice
de montage et de mise en service allemande.
...............................................................21
Por favor, consulte los gráficos en las instruc-
ciones alemanas de montaje y uso.
...............................................................30
Per le grafiche fare riferimento alle Istruzioni per
il montaggio e l’uso in tedesco.
...............................................................39
De tekeningen kunt u in de Duitse montage- en
bedrijfsinstructies vinden.
...............................................................48
Prosimy przyjąć grafikę z niemieckiej
instrukcji montażu i obsługi.

3
18-05.306e_GB.fm
0English
PROTRONIC Urinal Flush Valve, Complete Installation Kit
7612982102257 ......... 230 V AC
7612982102264 ......... 24 V DC
Please refer to the graphics in the German Installation and Operating Instructions.
0Table of Contents
1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of Product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Installation Example for AQUARAPID Installation Element . . . . . 6
Installation, Function and Commissioning
11. Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12. Assembly Instructions for 24 V DC Electrics . . . . . . . . . . . . . . . . 7
13. Assembly Instructions for 230 V AC Electrics . . . . . . . . . . . . . . . 8
14. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
15. Adjusting the Flush-Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
16. Adjusting the Flush Flow-rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
17. Setting the Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance
18. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
19. Changing the Solenoid Valve Cartridge . . . . . . . . . . . . . . . . . . . . 10
20. Replacing the O-ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
21. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
22. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4
18-05.306e_GB.fm
1. Abbreviations and Units
2. Key
Warning!
Failure to observe can result in injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimally handling the product.
3. Warranty
Liability is accepted according to the General Terms and Conditions of Business and
Supply.
Use original replacement parts only!
DN Nominal diameter in mm
RCD Residual Current Protective Device,
Earth leakage circuit breaker
TW Drinking water
TWW Hot drinking-water
EA-Nr. European Article Number
FAR-Best.-Nr. Franke Aquarotter Order Number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
18-05.306e_GB.fm
4. Important Notes
• Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.
• All technical connection regulations specified by the local water and electricity
supply utility companies must be complied with.
•5526 11 24-F: Secure the electric connection with an earth leakage circuit
breaker (RCD).
• All rights reserved to make technical alterations.
5. Application
Complete installation kit for PROTRONIC - non-touch, opto-electronically controlled
urinal flush-valve DN 15 for in-wall installation. Individual control unit in compact
design. Automatic forced flushing after 24 hours of non-use.
Optional: Function parameters adjustable by remote control.
5526 11 24-F … with mains connection
5526 12 24-F … for separate power supply
6. Technical Specifications
Minimum flow pressure: 1.0 bar
Recommended flow pressure: 1-4 bar
Maximum operating pressure: 10 bar
Calculation flow rate: 0.30 l/s
Flushing flow rate: 0.3 – 0.7 l/s
Flush water volume: 2 – 4 l
Flushing duration 0.6 – 6.5 s (adjustable in 6 steps)
Operating voltage:
5526 11 24-F 230 V AC, 50/60 Hz
5526 12 24-F 24 V DC
Operating voltage: 24 V DC
Power consumption:
5526 11 24-F 2.5 VA
5526 12 24-F 3 W
Type of protection: IP 54

6
18-05.306e_GB.fm
7. Scope of Delivery
8. Dimensions
9. Installation Example
10. Installation Example for AQUAFIX Installation Element
11. Assembly Instructions
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
11.1 Loosen the screws (a).
11.2 Cut off the shell protection (b) so it is flush with the front edge of the tiles.
11.3 Close the flow volume regulator (c) with a screwdriver, 8 mm head width.
☞Screw the flow volume regulator up to the stop limit.
☞Important!
Do not remove the circlip.
11.4 Remove the flush-plug (d).
11.5 Screw in the solenoid valve cartridge (e).
11.6 Use the flush-plugs as an assembly key to tighten the solenoid valve cartridge.
Item Description
1 Cover plate with control electronics and sensor
2 Self-closing solenoid valve cartridge
3 Connection terminal with coupling (supplied only for
24V DC model)
4 Transformer with connection terminal (supplied only for
230 V AC model)
5 Mounting frame (fastened in cover plate)
6 Extra items:
Cylinder head screws, plain washers, seal with screw
Installation and Operating Instructions

7
18-05.306e_GB.fm
☞Important!
• Carefully tighten the solenoid valve cartridge.
• Keep the flush-plugs in the flush-mounting cabinet to enable removal of the
solenoid valve cartridge at a later date.
11.7 Close the flow volume regulator (c) with a screwdriver, 8 mm head width.
☞Screw the flow volume regulator up to the stop limit.
☞Important!
Do not remove the circlip.
11.8 Remove the mounting frame from the cover plate by loosening the set screw.
5526 12 24-F (24 V DC)
11.9 Remove the protective earth conductor cable (f).
5526 11 24-F (230 V AC)
11.10 Fasten the protective earth conductor cable (I) to the mounting frame (m).
gNut
h Tooth washer
j Cable lug
kPin
11.11 Screw the mounting frame (m) on horizontally. The pin must face inwards.
12. Assembly Instructions for 24 V DC Electrics
12.1 Loosen screw (a) and remove the cover (b) of the connector terminal.
12.2 Connect the 2 x 1.5 mm² cable (c).
12.3 Plug the two connector terminals together.
12.4 Attach the connector terminals to the snap-fit fastener (simplified representation).
12.5 Connect the control unit and the connection terminal with the coupling.
12.6 Connect the control unit with the solenoid valve cartridge.
12.7 Adjust the flush-volume (see Chapter 15.).
12.8 Adjust the flush flow-rate (see Chapter 16.).
12.9 Place the cover plate (d) on the frame and hang it behind the flap on the mounting
frame.
12.10 Attach the cover plate with a set screw.

8
18-05.306e_GB.fm
13. Assembly Instructions for 230 V AC Electrics
13.1 Loosen the screws (a) and remove the cover (b) of the connector terminal.
Caution!
Connect only 230 V AC, 50/60 Hz to the connector terminal.
13.2 From the 3 x 1.5 mm² lead-in cable (c), connect cores L1 and N to the corresponding
clamps.
The middle terminal clamp stays free.
13.3 Screw on the cover (b).
13.4 Fasten the PE core (green/yellow) to the pin (d) in the flush-mounting cabinet.
13.5 Connect the connector terminals together.
13.6 Place the transformer (e) in the flush mounting cabinet.
13.7 Attach the connector terminal (f) to the snap-fit fastener (g) (simplified
representation).
13.8 Connect the plug connection between the transformer and the control unit.
13.9 Connect the control unit to the solenoid valve cartridge.
13.10 Plug the protective earth cable (h) to the PE-flap (i) on the cover plate.
13.11 Adjust the flush-volume (see Chapter 15.).
13.12 Adjust the flush flow-rate (see Chapter 16.).
13.13 Place the cover plate (k) on the frame and hang it behind the flap on the mounting
frame.
13.14 Attach the cover plate with a set screw.
14. Function
14.1 Stand in front of the urinal at least 10 s.
14.2 Walk away from the urinal.
• Water flows.
• Water flow stops automatically after a set flow duration.
☞Forced flushing has been factory set to take place after 24 h of disuse.
☞The flow duration, range of the sensor and forced flushing can be adjusted with the
optional remote control (FAR Order No. 5179 0000).

9
18-05.306e_GB.fm
15. Adjusting the Flush-Volume
15.1 Remove the cover plate.
15.2 Set the flow volume regulator to "fully opened" (see Chapter 11.7).
15.3 Disconnect the mains voltage supply for min. 60 seconds. The flush-volume setting
is activated.
15.4 Reconnect the voltage supply.
15.5 Wait for the confirmation flashing (1x long 3x short).
15.6 Hook in the cover plate.
15.7 Hold your hand a distance of 5-10 cm in front of the sensor. The LED flashes quickly.
15.8 After 5 seconds the indicator lamp automatically turns off.
15.9 Move your hand out of the sensor-detection area (at least 60 cm away).
15.10 Hold your hand a distance of 5 - 10 cm in front of the sensor. The LED flashes.
2 flashes, pause, 3 flashes, pause, 4 flashes, etc.
15.11 Move your hand out of the sensor-detection area (min. 60 cm) after the required
flash sequence is seen. After this, the fitting flushes with the set flush-volume. After
flushing, the flash sequence of the corresponding flush-volume is displayed.
P: Pause
15.12 Low flush-volume
15.13 High flush-volume.
Flush-volume OK:
15.14 Wait 20 seconds outside of the sensor-detection area (the fitting switches
automatically to the normal operating mode).
15.15 Fasten the cover plate (see Chapter 13.14).
Flush-volume NOK:
15.16 Hold your hand a distance of 5 - 10 cm in front of the sensor. The LED flashes.
2 flashes, pause, 3 flashes, pause, 4 flashes, etc.
16. Adjusting the Flush Flow-rate
16.1 Remove the cover plate (see Chapter 15.1).
16.2 Adjust the flush flow-rate.
+ Increase flush flow-rate
– Decrease flush flow-rate
16.3 Fasten the cover plate (see Chapter 13.14).

10
18-05.306e_GB.fm
17. Setting the Range
17.1 The sensor-detection range can be adjusted using the optional remote control (FAR
Order No. 5179 0000).
18. Maintenance and Servicing
Depending on the quality of the water, the local conditions and the rules and
regulations applicable on site, the fitting must be maintained and serviced at regular
intervals.
Properly use suitable cleaning agents that are not harmful to the fittings and rinse
with water after use. High-pressure cleaners must not be used for cleaning.
19. Changing the Solenoid Valve Cartridge
19.1 Remove the cover plate (see Chapter 15.1).
19.2 Close the flow-volume regulator (see Chapter 11.7).
19.3 Disconnect the line connection between the solenoid valve cartridge and the
electronic module.
19.4 Turn the solenoid valve cartridge out using the fitting key.
19.5 Reassemble in the reverse order.
☞Important!
• Carefully tighten the solenoid valve cartridge.
• Keep the flush-plugs in the flush mounting cabinet so that solenoid valve cartridge
can be removed at a later date if required.
20. Replacing the O-ring
20.1 Interrupt the water supply.
20.2 Remove the cover plate (see Chapter 15.1).
20.3 Remove circlip (a) with the appropriate pliers for inner circlips.
20.4 Use a screwdriver to unscrew the closing unit (b).
20.5 Replace the O-ring (c).
20.6 Reassemble in the reverse order.