Franke AQUAMIX AQRM175 User manual

ZMI_001_2000100069-AQRM312_#SALL_#AQU_#V3.fm/24.02.12
Installation and operating instructions Montażi instrukcja obsługi
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982003028
FAR-Best.-Nr.: 2000100917
AQRM175
EA-Nr.: 7612982000515
FAR-Best.-Nr.: 2000100070
AQRM311
EA-Nr.: 7612982000522
FAR-Best.-Nr.: 2000100069
AQRM312

2
Inhaltsverzeichnis11.fm
................................................................ 3
Please refer to the graphics in the German
Installation and Operating Instructions.
................................................................ 11
Prosimy przyjąć grafikęz niemieckiej instrukcji
montażu i obsługi.

3
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
0English
AQUAMIX Self-closing Single Mixer
7612982003028 ......... Vertical-mounted mixer tap
7612982000515 ......... Single clamp-on tap
7612982000522 ......... Dual clamp-on tap
Please refer to the graphics in the German Installation and Operating Instructions.
0Table of Contents
1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of Product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation, Function and Commissioning
10. Installation (FAR Order No. AQRM175) . . . . . . . . . . . . . . . . . . . . 5
11. Installation (FAR Order No. AQRM311) . . . . . . . . . . . . . . . . . . . . 6
12. Installation (FAR Order No. AQRM312) . . . . . . . . . . . . . . . . . . . . 6
13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
14. Adjusting the Flow Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15. Setting the Temperature Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance
16. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
17. Replacing an Aerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
18. Replacing the Grit Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
19. Replacing the Non-return Valve . . . . . . . . . . . . . . . . . . . . . . . . . . 9
20. Replacing the Functional Part . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
21. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
22. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
1. Abbreviations and Units
2. Key
Warning!
Failure to observe can result in injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimally handling the product.
3. Warranty
Liability is accepted according to the General Terms and Conditions of Business and
Supply.
Use original replacement parts only!
4. Important Notes
• Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.
• All technical connection regulations specified by the local water and electricity
supply utility companies must be complied with.
• All rights reserved to make technical alterations.
5. Application
AQUAMIX self-closing single mixer DN 15 with angled outlet, for connection to hot
and cold water. Adjustable flow duration.
SW Width A/F
EA-Nr. European Article Number
FAR-Best.-Nr. Franke Aquarotter Order Number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
6. Technical Specifications
7. Scope of Delivery
8. Dimensions
9. Installation Example
10. Installation (FAR Order No. AQRM175)
Warning!
Use the fitting only with the non-return valves and the grit filters specified.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
10.1 Apply sealing material to the S-connectors (a) and screw them in.
☞Apply grease to the O-rings on the S-connectors!
10.2 Place the wall plate (b) over the S-connectors, align it, and then secure it with the
nuts (c).
10.3 Slide the flange (d) on to the wall plate and secure it with the washer (e) and the
screw (f).
10.4 Insert the grit filters (g).
10.5 Screw in the faucet screw (h) until it protrudes 16 mm and the borehole is vertical.
☞Apply grease to the O-rings on the guide bushing!
10.6 Insert the guide bushings (i).
Minimum flow pressure: 1.0 bar
Recommended flow pressure: 1-5 bar
Maximum operating pressure: 10 bar
Calculation flow rate: 0,07 l/s 0,07 l/s
Volumetric flow: 0.10 l/s at a flow pressure of 3 bar
Flow duration at 38 °C: 1-15 s adjustable
Quantity Description
1 AQUAMIX self-closing single mixer
1 Installation and Operating Instructions

6
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
10.7 Attach the fitting (k).
10.8 Secure the fitting with the grub screw (l).
10.9 Turn on the water supply.
10.10 Check the connections for leaks.
11. Installation (FAR Order No. AQRM311)
Warning!
Use the fitting only with the non-return valves and the grit filters specified.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
☞Important!
When installing the distribution pipes, ensure that a gap of 45 mm is maintained. Drill
the boreholes so that they are exactly in line vertically. The correct distances of the
pipes as well as the positions of the boreholes must not be forced with the mixer
body and the cover.
11.1 Drill 14 mm holes into the distribution pipes (b).
11.2 Place the clamper (c) and seals on the pipes, and then screw-fasten from the rear
with the clamp cover (a).
☞Apply grease to the O-rings on the guide bushing!
11.3 Insert the grit filters (d) and the guide bushings (e) into the clamper (c).
11.4 Slide the fitting (g) on to the guide bushings.
11.5 Secure the fitting with the grub screw (f).
11.6 Turn on the water supply.
11.7 Check the connections for leaks.
12. Installation (FAR Order No. AQRM312)
Warning!
Use the fitting only with the non-return valves and the grit filters specified.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
☞Important!
When installing the distribution pipes, ensure that a gap of 45 mm is maintained. Drill
the boreholes so that they are exactly in line vertically. The correct distances of the
pipes as well as the positions of the boreholes must not be forced with the mixer
body and the cover.

7
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
12.1 Drill 14 mm holes into the distribution pipes (b).
12.2 Place the clamper (a) and seals on the pipes, and then screw-fasten from below with
the clamp cover (c).
☞Apply grease to the O-rings on the guide bushing!
12.3 Insert the grit filters (d) and the guide bushings (e) into the clamper (a).
12.4 Slide the fittings (g) on to the guide bushings.
12.5 Secure the fittings with the grub screws (f).
12.6 Turn on the water supply.
12.7 Check the connections for leaks.
13. Function
Triggering water flow
13.1 Press the push cap.
• Water flows.
• Water flow stops automatically after a set flow duration.
☞The flow time can be set in the range 1–30 s.
Selecting the temperature
14. Adjusting the Flow Duration
14.1 Use a screwdriver to carefully prise up the plug.
14.2 Remove the plug.
14.3 Loosen the grub screw using a hollow hexagon wrench.
14.4 Remove the push-cap handle.
14.5 Set the flow duration with a screwdriver.
a: Blade width 3 mm
+ longer flow duration (max. 50 s)
– shorter flow duration (min. 1 s)
14.6 Trigger the valve to measure the flow duration.
☞Important!
When replacing the push-cap handle, ensure that the driver bar latches into the
corresponding slot.
14.7 After setting the required flow time, replace the push-cap handle.
14.8 Reassemble in the reverse order.

8
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
15. Setting the Temperature Limiter
Warning!
If the hot-water supply temperature is more than 45 °C, set the temperature limiter.
Failure to observe can cause bodily harm due to scalding.
☞The temperature limiter is not a scald protector.
15.1 Remove the push-cap handle (siehe Kapitel 14.).
15.2 Use a screwdriver to carefully prise off the stop ring and then use your hand to pull it
off from the teeth.
15.3 Mount the push-cap handle and trigger the fitting.
15.4 Turn the push-cap handle until the desired maximum hot-water temperature is
reached.
15.5 Push the stop ring back on the teeth so that the nose of the stop ring is positioned up
against the right-hand stop of the housing.
☞Important!
While fitting the push-cap handle, make sure that the driving lug locks properly into
the corresponding groove (siehe Kapitel 14.).
15.6 Reassemble in the reverse order.
16. Maintenance and Servicing
Depending on the quality of the water, the local conditions and the rules and regula-
tions applicable on site, the fitting must be maintained and serviced at regular
intervals.
Perform maintenance on the following components:
• Aerators (siehe Kapitel 17.)
• Filters (siehe Kapitel 18.)
• Non-return valves (siehe Kapitel 19.)
Use suitable cleaning agents that are not harmful to the fittings in a proper manner
and rinse with water after use. High-pressure cleaners must not be used for
cleaning.
Removing the Fitting
Some maintenance work requires the fitting to be removed.
16.1 Turn off the water supply.
16.2 Trigger the valve.
16.3 Loosen the grub screw.
16.4 Pull off the fitting.

9
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
17. Replacing an Aerator
17.1 Unscrew the aerator (a).
17.2 Screw on the new aerator.
18. Replacing the Grit Filters
18.1 Remove the fitting (siehe Kapitel 16.).
18.2 Pull out the guide bushings (a).
18.3 Replace the grit filters (b).
☞Important!
Be careful to insert the grit filters the right way round.
18.4 Reassemble in the reverse order.
19. Replacing the Non-return Valve
19.1 Remove the fitting (siehe Kapitel 16.).
19.2 Pull out the guide bushings (a).
19.3 Use a special wrench (c; FAR Order No. 2000105636) to pull the non-return valves
(b) out of the fitting .
Caution!
Observe the installation direction of the non-return valves.
19.4 Reassemble in the reverse order.
20. Replacing the Functional Part
20.1 Turn off the water supply.
20.2 Trigger the valve.
20.3 Remove the push-cap handle (siehe Kapitel 14.).
20.4 Remove the circlip.
20.5 Remove the pressure spring and the handle socket.
20.6 Use a socket spanner to remove the functional part.
☞Important!
While fitting the push-cap handle, make sure that the driving lug locks properly into
the corresponding groove (siehe Kapitel 14.).
20.7 Reassemble in the reverse order.

10
ZMI_001_2000100069-AQRM312_#SEN_#AQU_#V3
21. Fault Correction
If you are unable to correct a fault or if the fault is not described in the fault correction
section, please inform our customer service department!
22. Replacement Parts
Fault Cause Remedy
Water does not flow – Stop valve is closed ➯Open it
– Functional part faulty ➯Replace it
Water flows conti-
nuously
– Functional part faulty ➯Replace it
– Aerator calcified ➯Clean it
Water flow too weak – Aerator calcified ➯Clean it
– Supply pressure too low ➯Check it
– Grit filter/Non-return valve dirty ➯Clean it
– Water flow regulator not fully
opened
➯Open it
Flow duration too
short or too long
– Incorrect setting ➯Adjust it
– Grit filter is clogged ➯Clean it
– Aerator/shower head clogged with
dirt
➯Clean it
– Functional part/upper section faulty ➯Replace it
Water is too hot – Temperature limit is incorrectly set
or not set at all
➯Adjust it
– Cold water is turned off ➯Open it
– Grit filter/Non-return valve in the
cold-water connection is faulty
➯Replace it
Water is too cold – Grit filter/Non-return valve in the
hot-water connection is faulty
➯Replace it
– Hot water is turned off ➯Open it
Bezeichnung Best.-Nr.
1 Push-cap handle . . . . . . . . . . . . . . 2000104775
2 Functional part . . . . . . . . . . . . . . . . 2000104372
3 Stop ring. . . . . . . . . . . . . . . . . . . . . 2000104837
4 Installation kit comprising:
O-rings
Non-return valves
Grit filters . . . . . . . . . . . . . . . . . 2000105492
5 Aerator (PU with 10 pcs.). . . . . . . . 2000104691
Zubehör Best.-Nr.
Theft-resistant aerator
with flow-rate regulator
6 l/min . . . . . . . . . . . . . . . . . . . 2000101160
Special wrench for theft-resistant
aerator . . . . . . . . . . . . . . . . . . . 2000105960
1 Replacement kit for functional part
Rubber parts
Pressure spring
Circlip
Sealing plug
Grub screw. . . . . . . . . . . . . . . . . . 2000104785