Franke AQCT0031 User manual

Installation and operating instructions Istruzioni per il montaggio e l’uso
Notice de montage et de mise en service Montage- en bedrijfsinstructies
Instrucciones de montaje y uso Montażi instrukcja obsługi
ZMI_001_2000103800-AQCT0031_#SALL_#AQU_#V2.fm / 25.03.19
EA-Nr.: 7612982182006
FAR-Best.-Nr.: 2000103800
AQCT0031
EA-Nr.: 7612982182013
FAR-Best.-Nr.: 2000103803
AQCT0032
DE
EN
FR
ES
IT
NL
PL

Inhaltsverzeichnis29_001.fm
- 2 -
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 15
Les graphiques sont disponibles dans la notice de montage et de
mise en service allemande.
...................................................................................... 27
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 40
Per le grafiche fare riferimento alle Istruzioni per il montaggio e
l’uso in tedesco.
...................................................................................... 52
De tekeningen kunt u in de Duitse montage- en bedrijfsinst-
ructies vinden.
...................................................................................... 64
Prosimy przyjąć grafikęz niemieckiej instrukcji montażu i obsługi.
EN
FR
ES
IT
NL
PL

- 3 -
ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
0English
AQUACONTACT – Shower Panel made of Mineral Composite, 6 V DC
7612982182006
AQCT0032 ................. With shower gel tray
Please refer to the graphics in the German Installation and Operating Instructions.
0Table of Contents
1. Abbreviations and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of Product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Properties of MIRANIT-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. Installation Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11. Jet dispersion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation, Function and Commissioning
12. Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
14. Setting the Flow Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
15. Setting the Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
16. Hygiene Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
17. Thermal Disinfection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
18. Setting Cleaning Switch-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance
19. Maintenance and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
20. Care Instructions for MIRANIT-S . . . . . . . . . . . . . . . . . . . . . . . . . 11
21. Cleaning the Jet Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
22. Replacing the Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
23. Replacing the Flow Rate Regulator . . . . . . . . . . . . . . . . . . . . . . . 12
24. Fault Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
25. Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EN

ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
- 4 -
1. Abbreviations and Units
2. Key
Warning!
Failure to observe can result in injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimally handling the product.
3. Warranty
Liability is accepted according to the General Terms and Conditions of Business and
Supply.
Use original replacement parts only!
DN Nominal diameter in mm
RCD Residual Current Protective Device,
Earth leakage circuit breaker
SELV Safety Extra Low Voltage
EA-Nr. European Article Number
FAR-Best.-Nr. Franke Aquarotter Order Number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.
!
!

- 5 -
ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
4. Important Notes
• Installation, commissioning and maintenance are to be performed only by a
qualified technician according to the instructions provided and in accordance with
legal requirements and acknowledged rules of technology.
• All technical connection regulations specified by the local water and electricity
supply utility companies must be complied with.
• Battery compartment including battery or power supply and extension cables must
be ordered separately (see Accessories, Chapter 25).
• All work must be carried out in a de-energised state.
• All rights reserved to make technical alterations.
5. Application
AQUACONTACT – Shower panel made of mineral composite MIRANIT-S, for
surface installation, with electronic time-control, battery-powered or mains operation.
For connecting to pre-mixed warm water or cold water.
Flow duration 30 seconds.
With integrated hygiene flushing (24h after the last use, for 10s). Functions are
activated with a reflection code on the sensor: Activation/deactivation of hygiene
flushing and cleaning shut-off (3 min).
Additional functions via optional remote control:
– Adjustable flow duration and time intervals
– Switchable from time-control to body reflection, maximum flow duration 300
seconds
– Program controlled thermal disinfection with safety switch-off
6. Technical Specifications
Minimum flow pressure: 1.0 bar
Recommended flow
pressure:
1–5 bar
Maximum operating
pressure:
10 bar
Calculation flow rate: 0.20 l/s
Supply voltage: 6 V DC
Power consumption: 1.5 W
Type of protection: IP 67

ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
- 6 -
7. Properties of MIRANIT-S
The resin-bonded mineral composite MIRANIT-S is a mixture of aluminium trihy-
drate, natural stone, high quality unsaturated polyester resin and colour pigments.
MIRANIT-S ensures high stability and fracture resistance.
The smooth, non-porous satin finish is very easy to clean and meets highest hygiene
standards.
8. Scope of Delivery
9. Dimensions
10. Installation Example
11. Jet dispersion
12. Assembly Instructions
Warning!
Only operate this valve in conjunction with the correct filters.
Failure to observe can result in an increased bacterial load in drinking water and
cause a health risk or even risk of death.
Warning!
• Use only safety extra low voltage (SELV) to operate the device. Do not earth the
components.
• For safe mains operation, the power supply must be secured with a residual
current device (RCD).
Failure to observe can mean risk of death or material damage, e.g. from electric
shock or fire.
Quantity Description
1 Shower panel with:
AQUACONTACT sensor, solenoid valve cartridge, lockable
water volume regulator, connecting hose and AQUAJET-
Slimline shower head
2 Connection bracket
1 Hook-in strip
1 Flow rate regulator 0.15 l /s
3 Screws, dowels
1 Installation and Operating Instructions
!
!

- 7 -
ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
☞Important!
Before installing, flush the pipes in compliance with DIN 1988.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall dowels may have to be used
(to be provided by the customer).
Fig. A: Water connection from above
Fig. B: Water connection from rear
12.1 Only when the water connection is from the rear: Install the connection bracket (a)
leak-tight.
12.2 Screw-in the water volume regulators(b) leak-tight.
12.3 Align the water volume regulator in such a way that the screw plug and the operating
element are freely accessible.
12.4 To ensure that the shower head can be adjusted within the height range of 2.10 m to
2.30 m, mark the installation holes at a height (c) of 2.12 m to 2.32 m from the upper
plane of the finished floor.
12.5 Drill according to the markings.
12.6 Insert the dowels.
12.7 Screw on the hook-in strip.
12.8 Hang in the shower panel.
12.9 Mark the other hole.
12.10 Remove the shower panel.
12.11 Drill according to the markings.
12.12 Insert the dowel.
☞The battery compartment and/or the power supply and extension cables are not
included (see Accessories, Chapter 25).
☞If a in-wall power supply is used, it must be installed about 3 m away from the
shower.
12.13 Connect the AQUACONTACT sensor (f) with
– a battery compartment (d)
or
– an in-wall mounted power supply (e).
☞When the battery charge level is too low, the LED flashes with a 20 s cycle.
12.14 Only when the water connection is from the rear: Bring forward work steps 12.16 to
12.18.
12.15 Hook the shower panel into the hook-bar strip and fasten with screws.
12.16 Connect the water supply.
12.17 Use a hollow hexagon wrench to open the water volume regulators.
g: closed
h: open
12.18 Check the water connections for leaks.

ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
- 8 -
13. Function
☞The remote control (not included, see Accessories Chapter 25) can be used to
select the operating mode time-controlled/body reflection.
Triggering time-controlled water flow
13.1 Allow your hand to approach the sensor.
• Water flows.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again.
☞The flow duration has been factory set to 30s.
Triggering body-reflection controlled water flow
13.2 Allow your hand to approach the sensor.
• Water flows.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again
or
– after leaving the sensor range.
14. Setting the Flow Duration
You can adjust the flow time from 10 seconds to 5 minutes seconds using the
remote control (not included, see Accessories Chapter 25).
15. Setting the Range
The range for body reflection can be set with the remote control (not included, see
Accessories Chapter 25).
16. Hygiene Flushing
☞At the factory, the hygiene flush function is set so that water flows for 10 seconds 24
hours after the flush was last activated.
The parameters for hygiene flushing can be set with the remote control (not
included, see Accessories Chapter 25).
Intervals of 0, 8, 24, 48 or 72 hours can be set for hygiene flushing (0 = hygiene
flushing disabled). You can adjust the flow time from 10 seconds to 10 minutes.

- 9 -
ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
Display for hygiene flushing on the fitting
16.1 Allow your hand to approach the sensor at a distance of about 10 cm for 3 seconds.
16.2 Move your hand away from the sensor between the 1st and 2nd flash of the LED.
• Hygiene flushing active: The LED flashes quickly 4 times.
• Hygiene flushing inactive: The LED flashes slowly 2 times.
Activating/deactivating hygiene flushing on the fitting
16.3 Allow your hand to approach the sensor at a distance of about 10 cm for 3 seconds.
16.4 Move your hand away from the sensor detection range between the 6th and 8th
flash of the LED.
• LED does not flash.
16.5 After 3 to 10 seconds, allow your hand to approach the sensor again at a distance of
approx. 10 cm.
16.6 After the third LED flash, move your hand back out of the sensor detection range.
• The LED flashes quickly 4 times. Hygiene flushing is activated.
or
• The LED flashes slowly 2 times. Hygiene flushing is deactivated.
17. Thermal Disinfection
This fitting provides the features necessary to perform thermal disinfection to reduce
the risk of Legionella infection.
Warning!
Protective measures for persons (scald-protection) must be provided during thermal
disinfection, e.g. closing off sanitary rooms.
Failure to observe can cause bodily harm due to scalding.
The operator is responsible for performing, monitoring and protocoling (room, tap,
date, time, temperature, duration).
Any liability claims by third parties attributed to the operator improperly performing
thermal disinfection are therefore declined by the manufacturer.
☞By default, thermal disinfection is set in such a way that after 5 minutes of exposure
the fitting cools down for 1 minute.
☞Thermal disinfection can only be initiated with the remote control.
The parameters for thermal disinfection can be set with the remote control (not
included, see Accessories Chapter 25).
Exposure durations of 3, 5, 10, 15 or 20 minutes can be selected for thermal disin-
fection. During the exposure period, water first flows continuously for 2 minutes, and
then it pulsates until the end of the exposure period (water and energy saving
function). Cooling times of 0, 1, 3, 5 or 10 minutes can be set.
!

ZMI_001_2000103800-AQCT0031_#SDE_#AQU_#V2_EN.fm
- 10 -
18. Setting Cleaning Switch-off
Cleaning switch-off can be set either with the remote control (not included, see
Accessories Chapter 25) or it can be activated directly on the fitting.
Cleaning switch-off on the fitting
18.1 Allow your hand to approach the sensor at a distance of about 10 cm for 3 seconds.
18.2 Move your hand away from the sensor detection range between the 3rd and 5th
flash of the LED.
• LED does not flash.
18.3 After 3 to 10 seconds, allow your hand to approach the sensor again at a distance of
approx. 10 cm.
18.4 After the third LED flash, move your hand back out of the sensor detection range.
• The fitting is switched off for 3 minutes.
• The LED flashes with a 10 second cycle.
☞When you allow your hand to approach the sensor at a distance of about 10 cm for
at least 3 seconds, the fitting is reactivated before the end of 3 minutes.
19. Maintenance and Servicing
Depending on the quality of the water, the local conditions and the rules and regula-
tions applicable on site, the fitting must be maintained and serviced at regular
intervals.
Perform maintenance on the following components:
• Shower head (see Chapter 21.)
• Filters (see Chapter 22.)
Properly use suitable cleaning agents that are not harmful to the fittings and rinse
with water after use. High-pressure cleaners must not be used for cleaning.
Removing the shower panel
Some maintenance work requires that the shower panel must be removed.
Caution!
Never let the shower panel hang by the connecting hoses.
!