Freund FE-IPDS-20WM User manual

FE-IPDS-20WM Quick Guide
ST4x20 screw X 2
Screw fixing seat X 2
M2.5 x 6 screw X 6
Allen Wrench X 1
Rope X 1
FE-IPDS-20WM X
1
Please make sure the package contains the following items:
Unpacking
Back cover X 1
M4x30 screw X 2
Universal Accessories :
Cable locking plate X
1
M3x6 screw X 2
Wall-mounting bracket X 1
Rubber Plug X 3
（S,M,L）
Wall-mounting screw X 4
3/5000
Wandnagel

Mic
Speaker
Call button&Status LED
Photosensitive sensor
Infrared sensor
Camera
Product Overview
RF card reader
FE-IPDS-20W
M
Infrared LED

With 86 embedded box in the wall
Installation
Fix the
wall-mounting
bracket on
embedded box with
two M4x30 screws.
Mark the two holes
of the wall-mounting
bracket on the wall.
Take down two
M4x30 screws and
remove the
wall-mounting
bracket.
Use a hand drill
with 5mm
diameter bit to
make two 25mm
depth holes in the
marked positions.
Insert two screw fixing
seats into the holes.
Fix the wall-mounting
bracket with two
ST4x20 screws and
two M4x30 screws.
Step1: Bracket/Box Installation
Wall Mounting

Without 86 embedded box in the wall
Mark the two holes of
the wall-mounting
bracket on the wall for
the screws.
Use a hand drill with
5mm diameter bit to
make four 25mm
depth holes in the
marked positions.
Insert four screw fixing
seats into the holes.
Fix the wall-mounting
bracket with four
ST4x20 screws.

Step2：Back Cover Installation
For convenient wiring,
hang FE-IPDS-20WM
on the wall-mounting
bracket with rope.
Make cables go through
the back cover,
connecting to the
corresponding interfaces
of the main board.
Fasten the back cover
with four M2.5x6
screws, then fix four
wall-mounting screws
on the back of
FE-IPDS-20WM.
Insert the four
wall-mounting screws on
the device into the
corresponding holes on the
wall-mounting bracket, and
then press down to slide the
wall-mounting screws into
the groove. Then use the
Allen Wrench to tighten the
device with two M3x6
screws.
After successful
installation, check
the stability of
device.
Select a suitable size
rubber plug to push all
the cables into the
back cover. Fix cable
locking plate to the
back cover with two
M2.5x6 screws.

LAN
PoE
FE-IPDS-20W
M
FE-IPDS-20WM
SIP Video Phone
PoE
PoE
Network Video Recorder
(third party)
PC
(third party)
PoE
PoE
FE-IPDS-20WM
FE-IPDS-20WM
Application Network Topology
Indoor Monitor
PoE

Configuration
1. Access the Web UI: Input the IP address into web browser to configure
the phone.
2. Account Registration: On web UI, go to the path: Account -> Basic page
Register Account and fill in the account information. (Please refer to user
manual for more information)
3. Configure the Push Button: On web UI, go to the path: Intercom ->
Basic -> Push Button to configure the call number.
4. Configure the code to open the relay: On web UI, go to the path:
Intercom -> Relay -> Relay ID/DTMF and choose the DTMF code number
in corresponding area.
IP Announcement
1. While FE-IPDS-20WM starts up normally, hold the call button for
several seconds after the Status LED turns blue, voice system will enter IP
announcement mode.
2. In announcement mode, the IP address will be announced periodically.
3. Press Call Button again to the announcement mode.
4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address
is gained.
Operation
Make a call:
1. Press the call button to call indoor SIP Phone.
2. During the talk, called party can press pre-configured code number to
unlock the door.
Receive a call:
FE-IPDS-20WM supports Auto Answer by default. Incoming call from
indoor device will be answered automatically.

FREUND ELEKTRONIKA d.o.o
International Burch University | Francuske revolucije bb | 71210 Ilidza | Bosnia and Hercegovina
www.ip-integra.com | [email protected] | Tel. [phone]
Name
Status
Description
Status
indicator
Blue
Normal status
Calling
Red
Restarting
Network is unavailable
Green
Initialing/Talking on a call
Receiving a call
Red/Blue
Firmware upgrading
Indicators
Note: For more LED settings, please refer
to FE-IPDS-20WM webUI: Intercom -> LED
Setting.
: Light ON
: Light OFF
0.25sec
0.25sec
0.25sec
0.25sec
0.25sec
0.25sec
0.05sec
0.05sec
0.05sec
0.05sec