Friedrich HazardGard 60 Hz Guide

SH15L30-B
SH20L30-B
HG-SVC-PRTS-07 (3-07)
Room Air Conditioners
60 Hz Models
2007 Service & Parts Manual

2
TABLE OF CONTENTS
Specifications.........................................................................................................................................................3
Performance Data..................................................................................................................................................3
Component Operation & Testing ...........................................................................................................................4
Compressors..........................................................................................................................................................4
Thermal Overload .................................................................................................................................................4
Checking Compressor Efficiency...........................................................................................................................4
Fan Motor...............................................................................................................................................................5
Solid State Relay....................................................................................................................................................5
System Control Switch ..........................................................................................................................................5
Run Capacitor ........................................................................................................................................................5
Thermostat.............................................................................................................................................................5
Low Ambient Bypass Valve....................................................................................................................................6
Sealed Refrigeration System Repairs....................................................................................................................6
Hermetic Component Replacement ......................................................................................................................7
Special Procedure in the case of Compressor Motor Burn-Out ..........................................................................7
Rotary Compressor Special Troubleshooting & Service ......................................................................................7
Refrigerant Charge.................................................................................................................................................7
Troubleshooting ................................................................................................................................................8-10
Wiring Diagram .................................................................................................................................................... 11
Cabinet Parts Diagram........................................................................................................................................ 12
Chassis Parts Diagram....................................................................................................................................... 13
Parts List .........................................................................................................................................................14-15
Warranty...............................................................................................................................................................16

3
EVAPORATOR AIR
TEMP. DEG. F EVAPORATOR
TEMP. DEG. F CONDENSER
TEMP.
DEG. F
Discharge
Temp Suction
Temp Liquid
Temp Super
Heat Sub-
Cooling
OPERATING
PRESSURES ELECTRICAL RATINGS R-22
REF. Evap
CFM Motor
RPM
BREAKER
FUSE
Discharge
Air Temp.
Drop F. E(in) E(out) Suction Discharge Amps
Cool Amps
Heat
Locked
Rotor
Amps
Charge
in OZ. 60 Hertz
Amps
60 Hz Models SH15L30-B 54 26 52 56 206 129 61 108 16 98 76 258 8.2 - - 28.5 363 1100 15 SH20L30-B 46 34 46 46 125 196 52 97 8 28 75 271 10.1 - - 39.0 357 1100 20
Due to continuing engineering research and technology, specifications are subject to change without notice. Manufactured under U.S. Design Patent DES 368, 306 decorative front; Utility Patent 5, 622, 058 MAXIMUM outdoor ambient operating temperature is 130°F (54°C). MAXIMUM TEMPERATURE RATING FOR CLASS I, DIVISION 2, GROUPS A,B,C,D
Model
Dimensions (Inches) Window Width
(Inches) Thru-The-Wall
Finished Hole
(Inches)
Circuit Rating
Breaker or
T - D Fuse
Weight
(Lbs.)
Height Width Depth
Overall
Depth
Hood to
Louvers
Minimum
Extension
Into
Room
Minimum
Extension
Outside Min. Max. Height Width Volts - Amps Net Shipping
SH15L30 15 15/16 25 15/16 27 3/89 3/16 3 1/16 16 15/16 27 7/842 16 3/16 26 3/16 250V - 15A 140 152
SH20L30 17 15/16 25 15/16 27 3/89 3/16 3 1/16 16 15/16 27 7/842 18 3/16 26 3/16 250V - 15A 166 179
Installation Information Product Specifications
Model
Cooling Capacity Electrical Characteristics (60 Hertz) Energy
Efficiency
Ratio AHAM
Moisture
Removal Air Direction
Controls Room Side Air
Circulation
(BTU/Hr.- AHAM) Volts Rated Amps
AHAM Watts EER (Pints/ Hr.) CFM
SH15L30 15000/15000 230/208 7.9/8.7 1765/1765 8.5/8.5 4.0 8-way 375 SH20L30 19800/19500 230/208 10.0/10.9 2200/2167 9.0/9.0 5.7 8-way 375
Performance Data: Cooling
OPERATING TEMPERATURE CODE T3B

4
COMPRESSOR WINDING TEST (Figure 2.)
Removethecompressorterminalboxcoveranddisconnectthe
wires fromthe terminals. Usingan ohmmeter, check continuity
across the following:
COMPONENT OPERATION AND TESTING
COMPRESSORS
Compressors are single phase, 208/230 volt. All compressor
motorsarepermanentsplitcapacitortype,usingonlyarunning
capacitor across the start and run terminal.
All compressors are internally spring mounted and externally
mounted on rubber isolators.
Line Voltage Overload
The compressor is equipped with an internal line voltage over-
load. This overload is embedded in the windings of the motor
to sense the motor temperature. The overload will open and
disconnect the power to the motor due to high temperatures
caused by:
1. A locked rotor.
2. Excessive running amps.
3. High discharge temperature.
4. Low refrigerant charge.
FIGURE 1 INTERNAL OVERLOAD
LINE BREAK
INTERNAL OVERLOAD
OHMMETER
FIGURE 2 COMPRESSOR WINDING TEST
Testing Procedures
1. Terminal "C" and "S" – no continuity – open winding
– replace compressor.
2. Terminal "C" and "R" – no continuity – open winding
– replace compressor.
3. Terminal "R" and "S" – no continuity – open winding
- replace compressor.
4. Terminal "C" and the shell of the compressor – continuity
– grounded motor – replace compressor.
5. Should continuity exist between terminals "R" and "S",
but not between terminals "C" and "S" and "C" and "R",
the internal overload may be open. If the compressor is
extremelyhot,allowitsufficienttimetocool.Itmayrequire
aslongasonehourforthecompressortocoolsufficiently
for the internal overload to close.
CHECKING COMPRESSOR EFFICIENCY
The reason for compressor inefficiency is normally due to bro-
kenordamaged suctionand/ordischarge valves, reducingthe
ability of the compressor to pump refrigerant gas.
This condition can be checked as follows:
1. Installapiercingvalveonthesuctionanddischargeorliquid
process tube.
2. Attach gages to the high and low sides of the system.
3. Start the system. Run a "cooling or heating performance test."
If test shows:
A. Below normal high side pressure.
B. Above normal low side pressure.
C. Low temperature difference across the coil.
The compressor valves are faulty - replace the compressor.
GROUND TEST
Use an ohmmeter set on its highest scale. Touch one lead to
thecompressorbody(cleanpointofcontact,asagoodconnec-
tion is a must) and the other probe in turn to each compressor
terminal.(SeeFigure3.)Ifareadingisobtained,thecompressor
is grounded and must be replaced.
FIGURE 3 TYPICAL GROUND TEST
WARNING
DISCONNECT ELECTRICAL POWER TO THE
UNIT BEFORE SERVICING OR TESTING

5
FAN MOTOR (Figure 4)
A 230 volt single phase permanent split capacitor motor is
used to drive the evaporator blower and condenser fan. A
running capacitor is wired across the start and run terminals
of the motor.
The motor is totally enclosed and is protected with a line volt-
age overload located internally of the motor. The motor shaft
is stainless steel to resist corrosion.
FAN MOTOR – TEST
Disconnect power to the unit.
1. Determine that the capacitor is serviceable.
2. Disconnect the black lead from the circuit board.
3. Apply "live" test cord leads to the common terminal of
the capacitor andtheblack lead.The motorshouldrun
at high speed.
SOLID STATE RELAY (Figure 5)
Two 50 amp rated 208/230 volt solid state relays are used to
energizethecompressorandfanmotor.Terminals3and4arethe
208/230 volt line side. Terminals 1 and 2 are load side contacts.
FIGURE 4
FAN MOTOR
SYSTEM CONTROL SWITCH (Figure 6)
This switch is double pole, single throw. Check for continuity
between terminals 2 and 3, and 5 and 6.
FIGURE 6
SWITCH, ON-OFF
CAPACITOR, RUN
A run capacitor is wired across the auxiliary and main winding
of a single phase permanent split capacitor motor such as the
compressor andfanmotors.Asinglecapacitor canbeusedfor
each motor or a dual rated capacitor can be used for both.
The capacitor’s primary function is to reduce the line current
while greatly improving the torque characteristics of a motor.
The capacitor also reduces the line current to the motor by
improving the power factor of the load. The line side of the
capacitor is marked with a red dot and is wired to the line side
of the circuit (see Figure 7.)
RED DOT
RUN CAPACITOR
FAN
MOTOR
COMPRESSOR
FIGURE 7 RUN CAPACITOR HOOK–UP
CAPACITOR – TEST
1. Remove the capacitor from the unit.
2. Check for visual damage such as bulges, cracks, or
leaks.
3. For dual rated capacitors, apply an ohmmeter lead to
the common (C) terminal and the other probe to the
compressor(HERM)terminal.Asatisfactorycapacitorwill
causeadeflectiononthepointer,thengraduallymoveback
to infinity.
4. Reverse theleadsoftheprobeandmomentarily touchthe
capacitorterminals.Thedeflectionofthepointershouldbe
two times that of the first check if the capacitor is good.
5. Repeat steps 3 and 4 to check the fan motor capacitor.
NOTE: A shorted capacitor will indicate a low
resistance and the pointer will move more to the “0”
end of the scale and remain there as long as the
probes are connected. An open capacitor will show
no movement of the pointer when placed across the
terminals of the capacitor.
LED indicates
contacts closed
when lit
Line side
Load side
FIGURE 5
SOLID STATE
RELAY

6
THERMOSTAT
A cross ambient thermostat is used to maintain the desired
comfort level. The thermostat reacts only to a change in
temperature at the bulb location. Important to the successful
operationoftheunitisthepositionofthesensingbulbinrelation
to the evaporator (see Figure 8).
TEST
Remove the wires from the thermostat. Turn the thermostat to
its coldest position. Check to see if there is continuity between
the two terminals. Turn the thermostat to its warmest position.
Check continuity to see if the thermostat contacts open.
Note:Thetemperaturemustbewithintherangelistedtocheck
the thermostat. Refer to the troubleshooting section in this
manual for additional information on thermostat testing.
LOW AMBIENT BYPASS VALVE (Figure 9)
The HazardGard unit is designed to operate at low outside
ambient temperatures. This is accomplished by the use of a
bypass valve installed in the refrigeration circuit. The valve
is connected between the discharge line at the compressor
and the suction process tube. The valve responds to suction
pressure which, when reduced in the system, causes the
valve to open and bypass hot gas from the high pressure side
to the low pressure side of the system. The hot gas entering
the compressor mixes with the cool gas returned through the
suction line, thus increasing the suction pressure. The valve
is preset to open when the suction pressure reaches 50 psig.
This pressure setting cannot be altered. The system can be
operated at outdoor temperatures as low as 45°F before the
evaporator coil will begin to accumulate frost.
To determine if the valve operates, block the return air to the
evaporator coil. Turn on the unit and touch the tube at the
bypass valve outlet which connects to the suction process
tube. When the low side pressure reaches approximately 50
psig,the valve willbegin toopenand thetube willgethot. This
method will determine if the valve is responding to the suction
pressure change.
FIGURE 9
LOW AMBIENT
Bypass VALVE
SEALED REFRIGERATION SYSTEM
REPAIRS
Equipment Required:
1. Voltmeter
2. Ammeter
3. Ohmmeter
4. E.P.A Approved Refrigerant Recovery System
5. Vacuum Pump (capable of 200 microns or less vacuum).
6. Acetylene Welder
7. Electronic Halogen Leak Detector (G.E. Type
H-6 or equivalent).
8. Accurate refrigerant charge measuring device
such as:
a. Balance Scales - 1/2 oz. accuracy
b. Charging Board - 1/2 oz. accuracy
9. High Pressure Gauge - (0-400 lbs.)
10. Low Pressure Gauge - (30" - 150 lbs.)
11. Vacuum Gauge - (0-1000 microns)
Equipment Must Be Capable of:
1. Recovering CFC’s as low as 5%.
2. Evacuation from both the high side and low side of the
system simultaneously.
3. Introducing refrigerant charge into the high side of the
system.
4. Accurately weighing the refrigerant charge actually intro-
duced into the system.
5. Facilities for flowing nitrogen through the refrigeration
tubing during all brazing processes.
RANGE: Thermostat
(Part No. 618-225-02)
60°F ( ± 2°) to 90°F( ± 4°)
FIGURE 8
SENSING
BULB LOCATION

7
NOTE: This procedure can be sped up by the use of
heatlamps,or bybreaking thevacuumwithrefrigerant
or dry nitrogen at 5,000 microns. Pressure system to 5
PSIGandleaveinthesystemaminimumof10minutes.
Recover refrigerant, and proceed with evacuation to a
pressure of 200 microns or a minimum of 10%.
11. Break the vacuum by charging the system from the high
side with the correct amount of refrigerant specified. This
will prevent boiling the oil out of the crankcase.
NOTE: If the entire charge will not enter the high side,
allow the remainder to enter the low side in small
increments while operating the unit.
HERMETIC COMPONENT REPLACEMENT
The following procedure applies when replacing components
in the sealed refrigeration circuit or repairing refrigerant leaks.
(Compressor,condenser,evaporator,capillarytube,refrigerant
leaks, etc.)
1. Recover the refrigerant from the system at the process
tube located on the high side of the system by installing
a line tap on the process tube. Apply the gauge from the
process tube to EPA approved gauges from the process
tube to the EPA approved recovery system. Recover the
CFC’s in the system to at least 5%.
2. Cuttheprocesstubebelowthepinchoffinthesuctionside
of the compressor.
3. Connect the line from the nitrogen tank to the suction
process tube.
4. Drift dry nitrogen through the system and unsolder the
more distant connection first. (Filter drier, high side
process tube, etc.)
5. Replace the inoperative component, and always install a
newfilterdrier. Drift dry nitrogen through thesystemwhen
making these connections.
6. Pressurize the system to 30 PSIG with proper refrigerant
and boost the refrigerant pressure to 150 PSIG with dry
nitrogen.
7. Leak test the complete system with the electric halogen
leak detector, correcting any leaks found.
8. Reduce the system to zero gauge pressure.
9. Connect the vacuum pump to the high side and low side
of the system with deep vacuum hoses, or copper tubing.
(Do not use regular hoses.)
10. Evacuate the system to an absolute holding pressure of
200 microns or less.
12. Restart the unit several times after allowing pressures
to stabilize. Pinch off the process tubes, cut and solder
the ends. Remove the pinch off tool, and leak check the
process tube ends.
SPECIAL PROCEDURES IN THE CASE OF
COMPRESSOR MOTOR BURNOUT
1. Recover all refrigerant and oil from the system.
2. Removethecompressor,capillarytubeandfilterdrierfrom
the system.
3. Flushtheevaporator,condenserandallconnectingtubing
withdrynitrogen,orequivalent,toremoveallcontamination
from the system. Inspect the suction and discharge lines
for carbon deposits. Remove and clean if necessary.
4. Reassemblethesystem,includinganewdrier-strainerand
capillary tube.
5. Proceed with processing as outlined under hermetic
component replacement.
ROTARY COMPRESSOR
SPECIAL TROUBLESHOOTING & SERVICE
Basically, troubleshooting and servicing rotary compressors
is the same as on the reciprocating compressor with only a
few exceptions.
1. Because of the spinning motion of the rotary, the mounts
are critical. If vibration is present, check the mounts
carefully.
2. Theelectricalterminalsontherotaryareinadifferentorder
thanthereciprocatingcompressors.Theterminalmarkings
areonthecovergasket.Useyourwiring diagramto insure
the correct connections.
REFRIGERANT CHARGE
1. The refrigerant charge is extremely critical. Measure the
chargecarefullyandasexactlyaspossibletothenameplate
charge.
2. The correct method for charging the rotary is to introduce
liquid refrigerant into the high side of the system with the
unit off. Then start the compressor and enter the balance
of the charge, gas only, into the low side.
Theintroductionofliquidintothelowside,withouttheuseof
a capillary tube, will cause damage to the discharge valve
of the rotary compressor.
NOTE:AllinoperativecompressorsreturnedtoFriedrich
must have all lines properly plugged with the plugs from
the replacement compressor.

8
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE TO CORRECT
UNIT DOES NOT RUN.
Power disconnected. Check power source.
System switch in “Off” position. Set switch correctly.
Branch circuit fuse blown or
circuit breaker tripped. Replace fuse, reset breaker. If repeats, check fuse or breaker size. Check for shorts in unit wiring and components.
Inoperative system switch. Test for continuity.
Loose or disconnected wiring
at switch. Check wiring and connections. Connect per wiring diagram.
Inoperative switch (On-Off). Test for continuity, 3 and 2, 5 and 6.
EVAPORATOR COIL
FREEZES UP.
Dirty Filter. Clean as recommended in Owner’s Manual.
Restricted air flow. Check for dirty or obstructed coil - clean as required.
Inoperative thermostat. Test for shorted thermostat or stuck contacts.
Short of refrigerant. De-ice coil and check for leak.
Partially restricted capillary. De-ice coil. Check temperature differential across coil. Touch test coil return bends for same temperature. Test for low
running current.
Inoperative fan motor. Test and replace if inoperative.
COMPRESSOR RUNS
CONTINUALLY.
DOES NOT CYCLE OFF.
Excessive heat load. Test cooling performance of unit. Unit undersized.
Restriction in line. Check for partially iced coil. Check temperature split across
coil.
Refrigerant leak. Check for presence of oil on silver soldered connections. Check for partially iced coil. Check split across coil. Check for
low running amperage.
Thermostat contacts stuck. Check operation of thermostat. Replace if contacts remain
closed.
THERMOSTAT DOES
NOT TURN UNIT ON.
Loss of charge in thermostat
bulb. Place jumper across thermostat terminals. If unit operates, replace thermostat.
Loose or broken parts in
thermostat. Check as above.
Incorrect wiring. Connect per wiring diagram.
System switch open. Test for continuity at switch terminals 2 and 3.
THERMOSTAT DOES
NOT TURN UNIT OFF.
Thermostat set at coldest point Turn to highest temperature setting to see of unit will cycle off.
Thermostat contacts stuck. Disconnect power to the unit. Remove cover of thermostat
and check if contact is stuck, if so replace thermostat.
Switch (On - Off) shorted. Test switch for open contacts at terminals 2 and 3 with switch
in “Off” position.

9
TROUBLESHOOTING (Continued)
PROBLEM POSSIBLE CAUSE TO CORRECT
COMPRESSOR
ATTEMPTS TO
START, OR RUNS
FOR SHORT
PERIODS ONLY.
CYCLES ON
OVERLOAD.
Compressor attempts to start
before system pressures are
equalized.
Allow a minimum of two (2) minutes to allow pressures to
equalize before attempting to start.
Low or fluctuating voltage. Check voltage with unit operating. Check for other appliances on the circuit. Unit should be on separate circuit
for proper voltage, and be fused separately.
Incorrect wiring. Connect per wiring diagram.
Shorted or incorrect capacitor. Check by substituting a known good capacitor of correct
rating.
Restricted or low air flow through
condenser coil. Check for proper fan speed or blocked condenser.
Compressor running abnormally
hot. Check for kinked discharge line or restricted condenser. Check amperage.
Overload opens too soon. Change compressor if all other corrections above are
normal.
COMPRESSOR DOES
NOT START - FAN
MOTOR RUNS.
Thermostat contacts not closing. Check continuity of thermostat at coldest setting. Jump
contacts, if compressor runs, replace thermostat.
Low voltage supply. Check for nameplate voltage.
Switch (On-Off) inoperative. Test for continuity.
Open capacitor. Check by substituting a known good capacitor of correct
rating.
Internal overload open. Check voltage at compressor terminals. If voltage is
satisfactory, replace compressor.
Relay open Replace relay
Open or shorted compressor
windings Check windings for continuity and resistance. Direct test compressor. If direct test fails, replace compressor.
DOES NOT COOL,
OR COOLS ONLY
SLIGHTLY.
Thermostat open or inoperative. Set to coldest position. Test thermostat and replace if
necessary.
Dirty air filter. Clean as recommended in Owner’s Manual.
Dirty or plugged condenser or
evaporator coil. Use steam or detergents to clean.
Poor air circulation in area being
cooled. Adjust air louvers.
Low capacity - undercharge. Clean, check for leak and make repair.
Compressor not pumping properly. Check amperage draw against nameplate. If not conclusive,
make pressure test.

10
TROUBLESHOOTING (Continued)
PROBLEM POSSIBLE CAUSE TO CORRECT
FAN MOTOR DOES
NOT RUN.
Defective switch (On-Off). Check continuity across terminals 2 and 3.
Fan capacitor open. Check by substituting a known good capacitor of the same
rating.
Inoperative fan motor. Direct test fan motor.
Incorrect wiring of fan circuit. Connect per wiring diagram.
Relay open. Replace Relay.
Check for seized motor bearings. Rotate by hand, add oil, if noisy, replace.
Bound fan blade or blower wheel. Adjust for proper clearance.
SWITCH (ON-OFF)
DOES NOT CUT
FAN MOTOR OFF. Selector Switch Relay Replace selector switch. Replace relay.
NOISY AND/OR
VIBRATION.
Poor installation. Refer to Installation Instructions for proper installation.
Fan blade striking chassis. Adjust motor mount to attain proper fan blade and blower
wheel clearance.
Compressor vibrating. Check for deteriorated compressor grommets, or missing
mounting parts.
Loose cabinet parts, improperly
mounted components, tubing
rubbing. Adjust and tighten as required.
WATER LEAKS
INTO ROOM.
Evaporator drain pan overflowing. Clean obstructed drain trough.
Condensation forming on bottom
of base pan. Evaporator drain pan broken or cracked. Reseal or replace.
Water dripping from discharge air
grilles. Dirty evaporator coil, or extremely high humidity conditions. Clean coil with steam or detergent.
OUTSIDE WATER
LEAKS.
Evaporator drain pan cracked or
obstructed. Repair and clean, or replace as required.
Water in center section of base
pan (compressor area).
Remove condenser shroud, Clean and remove old sealer
from base pan and shroud. Apply new sealer, reinstall and
check.
Dirty Condenser coil. Clean with steam or detergent.
Fan blade and slinger ring
improperly positioned. Adjust fan blade to 1/2" clearance from condenser coil.

11
WIRING DIAGRAM
MODELS SH15L30-B and SH20L30-B

12
HAZARDGARD CABINET PARTS

13
HAZARDGARD CHASSIS PARTS

14
HAZARDGARD PARTS LIST
REF DESCRIPTION PART NO# MODELS CODE
ELECTRICAL PARTS
SH15L30-B SH20L30-B
1 COMPRESSOR 61193549 1 600
1 COMPRESSOR 61193550 1 600
2 MOTOR, FAN 61871426 1110
2 MOTOR, FAN 61871427 1110
5 SWITCH, ON-OFF DPST 60935300 1 1 130
* INSULATOR, ELECTRICAL 61829700 1 1 399
* RELAY, SOLID STATE 61108800 2 2 399
6 THERMOSTAT 61822502 1 1 120
7 CAPACITOR 20/7.5 440 V. 61080546 1 150
7 CAPACITOR 25/7.5 440 V 61080547 1 150
* HARNESS, WIRE, COMP. 61821308 1 1 399
REFRIGERATION PARTS
SH15L30-B SH20L30-B
9 EVAPORATOR COIL 61850100 1 400
9 EVAPORATOR COIL 61850001 1 400
10 CONDENSER COIL 62050410 1 410
10 CONDENSER COIL 62050411 1 410
* DRIER, LIQUID 60308101 1 1 480
* CAPILLARY TUBE 01390005 1 471
* CAPILLARY TUBE 03760518 2 471
* VALVE, BY-PASS 60809500 2 520

15
HAZARDGARD PARTS LIST
REF DESCRIPTION PART NO# MODELS CODE
CHASSIS PARTS
SH15L30-B SH20L30-B
8 HOLDER, THERMOSTAT 61829800 1 1 999
11 KNOB, CONTROL 61493915 1 1 761
17 DECORATIVE PANEL 61822662 1 1 760
22 FAN BLADE, COND. 60542003 1 710
22 FAN BLADE, COND. 60542004 1 710
23 BLOWER WHEEL, EVAP. 60610616 1 700
23 BLOWER WHEEL, EVAP. 60610617 1 700
25 FAN MOTOR MOUNT 61802500 1 900
25 FAN MOTOR MOUNT 61804100 1 900
26 SHROUD, CONDENSER 61803601 1 720
26 SHROUD, CONDENSER 61804901 1 720
27 BRACE, COND.SHROUD 61802600 3 3 722
29 BLOWER FRONT 61817300 1 742
29 BLOWER FRONT 61817400 1 742
30 SCROLL 61814905 1 743
30 SCROLL 61817505 1 743
32 BASE PAN 61803444 1 1 730
34 BOLT, COMP. MOUNT 91400400 3 3 791
35 PLENUM ASSEMBLY 61831006 1 1 753
36 OUTER SHELL 61825708 1 770
36 OUTER SHELL 61825709 1 770
37 GRILLE, INTAKE 61808906 1 772
37 GRILLE, INTAKE 61811111 1 772
38 WINGBOARD 60294415 1 999
38 WINGBOARD 60294420 1 999
40 ANGLE, WINGBOARD TOP 61819711 1 1 999
41 ANGLE,WINGBORD SIDE 61819811 2 2 999
* LATCH, INTAKE GRILLE 61989000 2 2 752
* FILTER, AIR 60865808 1 754
* FILTER, AIR 60865809 1 754
* HOLDER, FILTER 61823000 2 2 756
* DRAIN PAN, EVAP. 61803800 1 1 840
* GROMMET, COMP. MOUNT 01193549 3 3 790
* REAR GRILLE 61818500 1 771
* REAR GRILLE 61818501 1 771
* BAG, ASSY. HARDWARE 60846016 1 1 999
* GASKET, CHASSIS 61717301 1 1 780
OPTIONAL ACCESSORY ITEMS
* DRAIN KIT, DC-2 01900235 11
* START KIT, CAP.\RELAY 01900312 11

HG-SVC-PRTS-07 (3-07)
FRIEDRICH AIR CONDITIONING CO.
Post Office Box 1540 · San Antonio, Texas 78295-1540
4200 N. Pan Am Expressway · San Antonio, Texas 78218-5212
[phone] · FAX [phone]
www.friedrich.com
Printed in the U.S.A.
Friedrich Air Conditioning Company
P.O. Box 1540
San Antonio, TX 78295
210.357.4400
www.friedrich.com
HAZARDGARD®
ROOM AIR CONDITIONERS
LIMITED WARRANTY
LIMITED ONE YEAR PARTS WARRANTY
1. Limited warranty – One year. Friedrich warrants that it will provide a replacement for any part of this HazardGard Room Air
Conditioner found defective in material or workmanship for a period of one (1) year from the date of original purchase.
2. Limited warranty – One year. The Friedrich warranty also covers the cost of labor for repairing any compressor, condenser,
evaporator or inter-connecting tubing found defective within the warranty period, providing the unit is returned to an authorized
Friedrich Repair Station located within the Continental United States.
The Friedrich warranty does not cover:
(1) Any charges for removal, transportation or reinstallation of the unit; (2) the cost of labor to replace parts other than those
described above; and (3) does not apply to any HazardGard Room Air Conditioner that has been subject to (a) accident, misuse,
flood, fire, or neglect; (b) repairs or alterations outside of the Friedrich Authorized Dealer or Service Center so as to affect adversely
its performance and reliability; or (c) any repairs or servicing as a result of using parts not sold or approved by Friedrich.
LIMITATIONS: This warranty is a LIMITED warranty. Anything in the warranty notwithstanding, IMPLIED WARRANTIES
FOR PARTICULAR PURPOSE AND MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE EXPRESS
WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.
(10-04)