FRO­NIUS 63A-3 User manual

Fronius prints on elemental chlorine free paper (ECF) sourced from certified sustainable forests (FSC).
/ Perfect Charging / Perfect Welding / Solar Energy
Fronius Smart Meter 63A-3
EN
Operating instructions
System monitoring
42,0426,0293,EN 007-04032021
www.youtube.com/FroniusSolar
LEARN MORE WITH
OUR HOW-TO VIDEOS

Contents
Safety rules 4
Explanation of safety notices 4
General 4
Environmental conditions 5
Qualified personnel 5
Copyright 5
Data protection 5
General 6
Device description 6
Symbols on the device 6
Positioning 6
Installation 8
Checklist for installation 8
Installation 8
Protective circuit 8
Cabling 9
Connecting the data communication cable to the inverter 9
Terminating resistors - Explanation of symbols 11
Terminating resistors 11
Multi-meter system - Explanation of symbols 12
Modbus participants - Fronius SnapInverter 13
Multi-meter system - Fronius SnapINverter 14
Modbus participants - Fronius GEN24 15
Multi-meter system - Fronius GEN24 inverter 16
Menu structure 17
Setting the address of the Fronius Smart Meter 17
Start-up 19
Fronius SnapINverter 21
General 21
Connecting to the Fronius Datamanager 21
Configuring the Fronius Smart Meter as the primary meter 21
Configuring the Fronius Smart Meter as a secondary meter 22
Fronius GEN24 inverter 23
General 23
Installation using the web browser 23
Configuring the Fronius Smart Meter as the primary meter 24
Configuring the Fronius Smart Meter as a secondary meter 24
Technical data 25
Technical data 25
Fronius manufacturer's warranty 27
3
EN

Safety rules
Explanation of
safety notices DANGER!
Indicates immediate danger.
▶If not avoided, death or serious injury will result.
WARNING!
Indicates a potentially hazardous situation.
▶If not avoided, death or serious injury may result.
CAUTION!
Indicates a situation where damage or injury could occur.
▶If not avoided, minor injury and/or damage to property may result.
NOTE!
Indicates a risk of flawed results and possible damage to the equipment.
General The device has been manufactured in line with the state of the art and according to
recognized safety standards. If used incorrectly or misused, however, it can cause:
- Injury or death to the operator or a third party
- Damage to the device and other material assets belonging to the operating com-
pany.
All personnel involved in commissioning, maintenance, and servicing of the device must:
- Be suitably qualified
- Have knowledge of and experience in dealing with electrical installations and
- Have fully read and precisely followed these Operating Instructions
The Operating Instructions must always be at hand wherever the device is being used. In
addition to the Operating Instructions, attention must also be paid to any generally
applicable and local regulations regarding accident prevention and environmental protec-
tion.
All safety and danger notices on the device:
- Must be kept in a legible state
- Must not be damaged
- Must not be removed
- Must not be covered, pasted or painted over
The terminals can reach high temperatures.
Only operate the device when all protection devices are fully functional. If the protection
devices are not fully functional, there is a danger of:
- Injury or death to the operator or a third party
- Damage to the device and other material assets belonging to the operating company
Any safety devices that are not fully functional must be repaired by an authorised spe-
cialist before the device is switched on.
Never bypass or disable protection devices.
4

For the location of the safety and danger notices on the device, refer to the section
headed "General remarks" in the Operating Instructions for the device.
Any equipment malfunctions which might impair safety must be remedied before the
device is turned on.
This is for your personal safety!
Environmental
conditions
Operation or storage of the device outside the stipulated area will be deemed as not in
accordance with the intended purpose. The manufacturer accepts no liability for any
damage resulting from improper use.
Qualified person-
nel
The servicing information contained in these operating instructions is intended only for
the use of qualified service engineers. An electric shock can be fatal. Do not carry out
any actions other than those described in the documentation. This also applies to quali-
fied personnel.
All cables and leads must be secured, undamaged, insulated and adequately dimen-
sioned. Loose connections, scorched, damaged or inadequately dimensioned cables and
leads must be immediately repaired by authorised personnel.
Maintenance and repair work must only be carried out by an authorised specialist.
It is impossible to guarantee that bought-in parts are designed and manufactured to meet
the demands made on them, or that they satisfy safety requirements. Use only original
spare parts (also applies to standard parts).
Do not carry out any alterations, installations, or modifications to the device without first
obtaining the manufacturer's permission.
Components that are not in perfect condition must be changed immediately.
Copyright Copyright of these operating instructions remains with the manufacturer.
The text and illustrations are all technically correct at the time of printing. We reserve the
right to make changes. The contents of the operating instructions shall not provide the
basis for any claims whatsoever on the part of the purchaser. If you have any sugges-
tions for improvement, or can point out any mistakes that you have found in the instruc-
tions, we will be most grateful for your comments.
Data protection The user is responsible for the safekeeping of any changes made to the factory settings.
The manufacturer accepts no liability for any deleted personal settings.
5
EN

General
Device descrip-
tion
The Fronius Smart Meter is a bidirectional electricity meter which optimises self-con-
sumption and records the household's load curve. In conjunction with the Fronius
inverter, Fronius Datamanager and Fronius data interface, the Fronius Smart Meter
provides a clear overview of a user's own power consumption.
The meter measures the power flow to the loads or to the grid and forwards the informa-
tion via the Modbus RTU/RS485 communication to the Fronius inverter.
CAUTION!
Observe and follow safety instructions!
Failure to observe the safety instructions will result in damage to personnel and equip-
ment.
▶Switch off the power supply before establishing a mains connection.
▶Observe the safety instructions.
Symbols on the
device
Technical data, markings and safety symbols are located on the Fronius Smart Meter.
These must not be removed nor painted over. The notices and symbols warn of incorrect
operation that could result in serious injury and damage to property.
Symbols on the rating plate:
CE mark
The devices conform to all the requisite and relevant standards and guidelines
that form part of the relevant EU directive, and are therefore permitted to dis-
play the CE mark.
Regulatory Compliance Mark (RCM)
Complies with all applicable regulatory requirements in Australia and New Zea-
land regarding safety and electromagnetic compatibility, as well as specific
requirements for radio equipment.
WEEE mark
In accordance with European Directive 2012/19/EU on waste electrical and
electronic equipment and its implementation in national law, used electrical
devices must be collected separately and recycled in an environmentally
responsible manner. Ensure that you return your used device to your dealer or
obtain information regarding a local, authorised collection and disposal system.
Failure to comply with this EU Directive may result in a negative impact on the
environment and your health!
Positioning The Fronius Smart Meter can be installed at two possible locations in the system: at the
feed-in point and at the consumption point.
6

Placement at the feed-in point
Fronius Smart Meter located at the feed-in point.
Placement at the consumption point
Fronius Smart Meter located at the consumption load.
7
EN

Installation
Checklist for
installation
For installation information, see the following chapters:
1Switch off the power supply before establishing a mains connection.
2Mount the Fronius Smart Meter (see Installation on page 8).
3Connect automatic circuit breakers or automatic circuit breakers and disconnectors
(see Protective circuit on page 8).
4Connect the mains cable to the Fronius Smart Meter (see Cabling on page 9).
5Connect the output terminals of the Fronius Smart Meter to the Fronius inverter (see
Connecting the data communication cable to the inverter on page 9).
6If necessary, set terminating resistors (see Terminating resistors on page 11).
7Tug on each wire and plug to make sure that they are securely connected to the ter-
minal blocks.
8Switch on the power supply to the Fronius Smart Meter.
9Check the firmware version of the Fronius inverter. To ensure compatibility between
the inverter and the Fronius Smart Meter, the software must always be kept up to
date. The update can be started via the inverter web page or using Solar.web.
10 If several Fronius Smart Meters are installed in the system, set the address (see
"Setting the address" under Setting the address of the Fronius Smart Meter on
page 17).
11 Configure and commission the meter (see Start-up on page 19).
Installation The Fronius Smart Meter can be mounted on a 35 mm DIN rail. The housing comprises
4 DUs (division units, max. 72 mm).
Protective circuit The Fronius Smart Meter is a hard-wired device and requires a disconnecting device (cir-
cuit breaker, switch or disconnector) and overcurrent protection (automatic circuit
breaker).
The Fronius Smart Meter consumes 10 - 30 mA. The nominal capacity of the disconnect-
ing devices and the overcurrent protection is determined by the wire thickness, the mains
voltage and the required breaking capacity.
- Disconnecting devices must be mounted within sight and as close as possible to the
Fronius Smart Meter; they must also be easy to use.
- The disconnecting devices must satisfy the requirements of IEC 60947-1 and IEC
60947-3, as well as all national and local regulations for electrical systems.
- Use overcurrent protection rated for max. 63 A.
- To monitor more than one mains voltage, use connected automatic circuit breakers.
- The overcurrent protection must protect the mains terminals marked L1, L2 and L3.
In rare cases, the neutral conductor has an overcurrent protection which must simul-
taneously interrupt neutral and unearthed lines.
8

Cabling WARNING!
Danger from mains voltage.
An electric shock can be fatal.
▶Switch off the power supply before connecting the mains voltage inputs to the
Fronius Smart Meter.
IMPORTANT!
Do not install more than one cable per screw terminal. If necessary, use terminal blocks.
Rate fuse according to the cross-section of the line.
Current path connection cross-section:
- Wire (rigid): min. 1 mm² / max. 16 mm²
- Wire (flexible): min. 1 mm² / max. 10 mm²
- Recommended torque: 1.2 Nm / max. 1.4 Nm
Data communication and neutral conductor connection cross-section:
- Wire (rigid): min. 0.05 mm² / max. 4 mm²
- Wire (flexible): min. 0.05 mm² / max. 2.5 mm²
- Recommended torque: 0.5 Nm / max. 0.8 Nm
Connect each voltage cable to the terminal strip as shown in the graphic below.
Connecting the
data communica-
tion cable to the
inverter
Fronius SnapINverter:
Connect the data communication connections of the Fronius Smart Meter to the Fronius
system monitoring in the inverter. Several Smart Meters can be installed in the system,
see chapter Multi-meter system - Fronius SnapINverter on page 14.
9
EN

1Connect A to D+.
2Connect B to D-.
3ConnectC to -.
Fronius GEN24 inverter:
Connect the data communication connections of the Fronius Smart Meter to the Modbus
interface of the Fronius GEN24 inverter. Several Smart Meters can be installed in the
system, see chapter Multi-meter system - Fronius GEN24 inverter on page 16.
1Connect A to M1+.
2Connect B to M1-.
3Connect C to GND.
ATTENTION! ?
More information on successful commissioning.
Note the following information about connecting the data communication cable to the
inverter.
▶Use cables of type CAT5 or higher.
▶Use a mutual twisted cable pair for data lines that belong together (D+, D- and M1+,
M1-).
▶If the output cables are close to the mains cabling, use wires or cables that are
designed for 300 V to 600 V (never less than the operating voltage).
▶Use double-insulated or sheathed output cables when they are close to bare con-
ductors.
▶Use shielded twisted pair cables to avoid faults.
▶The outputs of the Fronius Smart Meter are electrically isolated from hazardous
voltages.
10