/ Perfect Welding /Solar Energy / Perfect Charging
QUICK START GUIDE
Fronius Smart Meter TS 65A-3
42,0410,2496 005-13102020 FRONIUS INTERNATIONAL GMBH www.fronius.com
DE: WARNUNG! Fehlbedienung und fehlerhaft durchgeführte Arbeiten können schwerwiegende Personen- oder
Sachschäden verursachen. Die Installation und Inbetriebnahme des Smart Meters darf nur durch geschultes Personal und
nur im Rahmen der technischen Bestimmungen erfolgen. Vor Arbeiten mit dem Gerät, alle beiliegenden, aufgedruckten
und online zur Verfügung gestellten Dokumente lesen und verstehen! Dieses Dokument beschreibt nicht alle möglichen
Systemkongurationen.
EN: WARNING! Incorrect operation and incorrectly performed work can cause serious personal injury or material damage. The Fronius
Smart Meter may only be installed and commissioned by trained personnel and only within the scope of the technical regulations. Befo-
re working with the device, read and understand all enclosed, printed and online documents! This document does not describe all of the
possible system congurations.
FR: AVERTISSEMENT ! Une mauvaise utilisation et un travail mal eectué peuvent causer des blessures graves ou des dommages
matériels. Le Fronius Smart Meter ne peut être installé et mis en service que par du personnel formé et uniquement dans le cadre des
réglementations techniques. Avant de travailler avec l’appareil, lisez et comprenez tous les documents ci-joints, imprimés et en ligne ! Ce
document ne décrit pas toutes les congurations possibles du système.
IT: ATTENZIONE! Un funzionamento non corretto e un lavoro eseguito in modo non corretto possono causare gravi lesioni personali o
danni materiali. Lo Fronius Smart Meter può essere installato e messo in funzione solo da personale addestrato e solo nell’ambito delle
norme tecniche. Prima di lavorare con l’apparecchio, leggere e comprendere tutti i documenti allegati, stampati e online! Questo docu-
mento non descrive tutte le possibili congurazioni di sistema.
ES: ¡ADVERTENCIA! El funcionamiento incorrecto y el trabajo realizado de forma incorrecta pueden causar graves lesiones personales o
daños materiales. El Fronius Smart Meter sólo puede ser instalado y puesto en marcha por personal capacitado y sólo dentro del ámbito
de los reglamentos técnicos. Antes de trabajar con el dispositivo, lea y entienda todos los documentos adjuntos, impresos y en línea! Este
documento no describe todas las conguraciones posibles del sistema.
DA: ADVARSEL! Forkert betjening og forkert udført arbejde kan forårsage alvorlig personskade eller materielle skader. Fronius Smart
Meter må kun installeres og idriftsættes af uddannet personale og kun inden for rammerne af de tekniske forskrifter. Læs og forstå alle
vedlagte, trykte og online dokumenter, før du arbejder med enheden! Dette dokument beskriver ikke alle mulige systemkongurationer.
Detailed, country-specic warranty terms are available on: www.fronius.com/solar/warranty
FIND MORE
INFORMATION
manuals.fronius.com/html/4204260349
SOFTWARE REQUIREMENTS
Fronius Datamanager 2.0 ≥ 3.16.1 version
Fronius Symo Hybrid ≥ 1.16.1 version
MEASURING INPUT
Nominal voltage (4-conductor) range 208 - 400 V (±20%)
Power consumption in the voltage path (max. voltage) ≤ 10 VA
Nominal frequency
Tolerance
50 - 60 Hz
45 - 65 Hz
Nominal current, lb5 A
Maximum current, Imax 65 A
Starting current 20 mA
Short-time overload
(EN IEC 62053-21, EN IEC 62053-23)
30 lmax / 0.001 s
Self-consumption - current path (max. current) ≤ 1 W
Power factor
Operating range
(EN IEC 62053-21, EN IEC 62053-23)
active cosφ 0.5 ind - 0.8 cap,
reactive sinφ 0.5 ind - 0.5 cap
Current distortion factor in acc. with EN 50470
OUTPUT
RS485 communication (Electrically isolated from measuring input)
Standard RS485 - 3 conductors
Protocol Compatible with Modbus RTU
Addresses 1 - 255
Baud rate 300, 2400, 9600 bit/s
Response time ≤ 200 ms
INSULATION (EN IEC 62052-11, EN IEC 62053-21)
Installation category III
Degree of pollution 2
Insulation voltage 4 kVAC RMS (1 min)
ELECTROMAGNETIC COMPATIBILITY
Emission test In acc. with EN IEC 62052-11, EN 50470-3
Immunity test In acc. with EN IEC 62052-11, EN 50470-3
OPERATING CONDITIONS
Reference temperature 25 °C (± 5 °C)
Operating range -25 to +55 °C
Temperature limit for storage and transport -30 to +80 °C
Mechanical environment
Electromechanical environment
M2
E2
HOUSING
Housing 3 modules according to DIN 43880
Sealable housing/terminal cover
Connection Screw connection
Mounting Can be snapped onto 35 mm DIN rail
Housing material Noryl, self-extinguishing
Degree of protection (EN 60529) IP51 housing, IP20 connections
Weight 240 grams
TERMINALS - MEASURING INPUT
Wire min. 1 mm² / max. 16 mm²
Recommended torque max. 2.8 Nm
TERMINALS - DATA OUTPUT (N-CONNECTOR)
Wire min 0.05 mm²
Recommended torque max. 0.4 Nm
