Fuji Electric MICREX-F Series User manual

1
Fuji Electric Co.,Ltd.
MICREX-F Series
SIO Driver
1 System Configuration.......................................................................................................3
2 Selection of External Device............................................................................................7
3 Example of Communication Setting.................................................................................8
4 Setup Items....................................................................................................................24
5 Cable Diagram...............................................................................................................29
6 Supported Device...........................................................................................................44
7 Device Code and Address Code....................................................................................46
8 Error Messages..............................................................................................................47

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 2
Introduction
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of External
Devices which can be connected and SIO
type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External
Device to be connected and connection
method.
)"2 Selection of External Device" (page 7)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting"
(page 8)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro Ex or in offline mode.
)"4 Setup Items" (page 24)
5Cable Diagram
This section shows cables and adapters
for connecting the Display and the
External Device.
)"5 Cable Diagram" (page 29)
Operation

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of Fuji Electric Co.,Ltd. and the Display are
connected is shown.
Connection Configuration
RS232C
• 1:1 Connection
Series CPU Link I/F SIO Type Setting Example Cable
Diagram
File Switch
MICREX-F
F80H
F120H
F250
RS232C interface
on FFU120B RS232C Setting
Example 1
(page 8)
Setting
Example 2
(page 11)
Cable
Diagram 1
(page 29)
RS485 interface
on FFU120B RS422/485 (4wire)
Setting
Example 3
(page 13)
Setting
Example 4
(page 16)
Cable
Diagram 2
(page 32)
F30 *1
F50 *1
F60
F70
F70S
F80
F80H
F81
F120
F120H
F120S
F200
F250
*1 When you use F30 or F50 for T link connection, T link master adaptor (FTM050A) is necessary.
RS232C interface
on FFK120A-C10 RS232C Setting
Example 1
(page 8)
Setting
Example 5
(page 18)
Cable
Diagram 1
(page 29)
RS485 interface
on FFK120A-C10 RS422/485 (4wire)
Setting
Example 3
(page 13)
Setting
Example 6
(page 20)
Cable
Diagram 2
(page 32)
FFK100A-C10 *2
*2 You cannot use FFK100A-C10 or NC1L-RS2 in 1:n configuration.
RS232C --- Setting Example 7
(page 22)
Cable
Diagram 3
(page 42)
F70
F70S NC1L-RS2*2 *3
*3 When you install 2 link units on the extension base unit created by T link function based on the basic base
unit of the External Device, you can connect the Display on either of 2 link units (simultaneous connection
on both 2 link units are not available). When you install 2 basic base units, simultaneous connection on both
2 link units are available.
RS232C Setting Example 1
(page 8)
Setting
Example 2
(page 11)
Cable
Diagram 4
(page 43)
External Device
RS232C
Display
Operation mode:1

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 4
• 1:n Connection
* Turn ON the termination resistance switch on the interface which terminates the RS422 connection.
RS422/485 (4wire)
• 1:1 Connection
* Turn ON the termination resistance switch on the External Device interface.
• 1:n Connection
* Turn ON the termination resistance switch on the interface which terminates the RS422 connection.
RS232C
External Device*
External Device External Device*
RS422/485 (4wire)
Operation mode:2 Operation mode:3
Operation mode:3
Max 16 units
Display
RS422/485 (4wire)
External Device*
Operation mode:
3
RS422/485 (4wire)
Display
Operation mode:3 Operation mode:
3
Operation mode:3
Max 16 units
RS422/485 (4wire)
Display
RS422/485 (4wire) RS422/485 (4wire)
External Device External Device External Device*

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 5
IPC COM Port
When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please
refer to the IPC manual for details.
Usable port
DIP Switch setting: RS-232C
Series Usable Port
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
PS-2000B COM1*1 , COM2,
COM3*1, COM4
*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.
--
PS-3450A, PS-3451A,
PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS-3650A (T41 model),
PS-3651A (T41 model) COM1*1 --
PS-3650A (T42 model),
PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2
PS-3700A (Pentium®4-M)
PS-3710A COM1*1, COM2*1, COM3*2 , COM4
*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.
COM3*2 COM3*2
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
PS4000*3
*3 When making communication between an External Device and COM port on the Expansion slot,
only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the
specification of COM port.
For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.
Please refer to the IPC manual for details of pin layout.
COM1, COM2 - -
PL3000 COM1*1*2, COM2*1,
COM3, COM4 COM1*1*2 COM1*1*2
DIP Switch Setting Description
1OFF
*1
*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.
Reserved (always OFF)
2OFF
SIO type: RS-232C
3OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 6
DIP Switch setting: RS-422/485 (4 wire)
DIP Switch setting: RS-422/485 (2 wire)
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available
9ON
RS (RTS) Auto control mode: Enabled
10 ON

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 7
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Number of Devices/
PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the display.
Manufacturer Select the manufacturer of the External Device to connect. Select "Fuji Electric Co.,Ltd.".
Series
Select the External Device model (series) and the connection method. Select "MICREX-F
Series SIO".
In System configuration, make sure the External Device you are connecting is supported by
"MICREX-F Series SIO".
)"1 System Configuration" (page 3)
Port Select the Display port to be connected to the External Device.
Use System Area
Check this option to synchronize the system data area of the Display and the device
(memory) of the External Device. When synchronized, you can use the External Device’s
ladder program to switch the display or display the window on the Display.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
This feature can also be set in GP-Pro EX or in the Display's offline mode.
Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] - [System
Area] Settings Guide"
Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area Settings"

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 8
3 Example of Communication Setting
Examples of communication settings of the Display and the External Device, recommended by Pro-face, are
shown.
When you use the MICREX-F Series, use GP-Pro EX and the ladder software to set as below.
3.1 Setting Example 1
Settings of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 9
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
Setting of External Device
(1) Turn OFF the DIP switch No.8 "Initialization method" on the rear panel of general-purpose interface module
of the External Device. Other settings are not necessary. The DIP switch setting will be effective after restart.
Use the rotary switch for MODE setting.
(2) Set the mode switch key of the External Device body to [TERM].
(3) Startup the ladder software. Execute [New File] from the [File] menu.
(4) Select the model of the External Device to use.
No. Setup Items Setup Description
1 No need
Unused
2 No need
3 No need
4 No need
5 No need
6 No need
7 No need
8OFF Initial file setting effective

MICREX-F Series SIO Driver
GP-Pro EX Device/PLC Connection Manual 10
(5) Create the default file in the data table. Please refer to the manual of the External Device for the default file
number or the setting method. When you select MODE2 or 3, use the rotary switch to specify the same
number as the station No. in the device setting. The setting is not necessary for MODE1 (RS232C 1:1
connection). Please refer to the connection configuration diagrams for more details.
(6) Select [Transfer] from the [File] menu to transfer to the External Device body.
(7) After the transfer is completed, restart the External Device.
Setup Items Setup Description Notes
MODE switch Depending on connection type Set by the rotary switch
Station No. Depending on connection type
Transmission Procedure No procedure
Set by the initial file
Mode Settings
Baud rate 19200
Data Bit 7
Parity Bit Even
Stop Bit 2
DCE/DTE DCE
CTS/RTS Always ON
DSR/DTR Always ON
Send Condition None
PK Access Enable
Transmission Code JIS
Code Conversion Enable
Head Code STX
End Code ETX
Head Code 1, 2 0
End Code 1, 2 0
BCC None