FujiFilm XG5000 User manual

Printed in Japan
XG5000/XG2000
CR-IR 362
Service Manual
No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by means, electronic,
mechanical, photocopying, recording or otherwise, without the prior
written permission of FUJIFILM Corporation.
FDR is a trademark or a registered trademark of FUJIFILM Corporation.
<No part of this manual may be reproduced or transmitted.>
Copyright ©2003-2009 by FUJIFILM Corporation. All rights reserved.
The relationship between mR (milliroentgen), which is the
unit of radiation, and μC/kg (micro-coulomb/kilogram),
which is the SI derived unit of radiation, is as follows.
1 mR = 0.258μC/kg
FUJI COMPUTED RADIOGRAPHY
Document No. 011-207-09A
1st Edition - Oct. 10, 2003
Revised Edition - Sep. 30, 2009
#20001 or Later #50001 or Later

BLANK PAGE

CR-IR 362 Service Manual
0.1
0.1
011-207-07E
02.19.2007 FM5097
1. Handling of This Manual
1.1 About This Manual
Scope
This Service Manual is applicable to Fuji Computed Radiography CR-IR362. The
machine is categorized as Class 1 according to IEC classication.
Notation of Unit Symbols
For notation of unit symbols, metric units set forth in the International Systems of Units
(SI) are used, as a rule. However, metric units that are allowed in the Measurement
Law, not in the SI, are used in some cases.
1.2 Precautions for Handling of This Manual
1. FUJIFILM Corporation reserves all rights related to this manual.
2. This manual should be accessible only to technical service personnel authorized by
FUJIFILM Corporation.
3. Since this manual contains condential information of FUJIFILM Corporation, such
as the internal structure of the product, appropriate measures should be taken to
prevent illegal or inappropriate disclosure and/or use of this manual.
4. The following conducts are prohibited without prior written approval of FUJIFILM
Corporation:
- Copy or transcribe a whole or part of the contents of this manual
- Disclose, furnish, lend, and/or transfer a whole or part of the contents of this
manual to persons other than the afore-described technical service personnel.
- Use a whole or part of the contents of this manual for purposes other than
technical servicing of the product.
5. Portions of the descriptions in this manual may be revised due to improvements on
the product.
1.3 About Notation in the Manual
Notation of cautions, warnings, etc.
The notation formats of "warning", "caution", "Instruction", "note", and "reference" are
shown below.
WARNING
Used when death or serious injury may occur if the instruction is not observed.
CAUTION
Used when minor or medium levels of physical injury may be incurred if the
instruction is not observed.
Also used when the machine may suffer serious trouble (such as unrecoverable
or difcult-to-recover trouble).
INSTRUCTION
Used when the machine may suffer damage, or any failure or malfunction may occur,
if the instruction is not observed.
NOTE
Used to indicate the matters that need attention during steps of the procedure.
REFERENCE
Used to indicate terminology or supplemental explanations.
Indication of Refer To
The " " mark is used to indicate the chapter or section you should refer to.
Its format is as indicated below.
{MC:9.1_Erasure conveyor unit}
Notation in the Manual
In this Service Manual, the CR-IR362 is sometimes denoted simply as the RU (Reader
Unit), and the CR-IR346/348CL as the CL.

CR-IR 362 Service Manual
0.2
0.2
011-207-08E
09.30.2008 FM5340
Notation of Symbols
- Check/Adjustment indicator:Indicates that it is necessary to check or adjust the
installation location when the part or component
removed is to be reinstalled.
This indicator is placed in the illustration that depicts
the procedures for removing the parts and components.
When you see this indicator, refer to its relevant
"
Check/Adjustment Procedures."
- Half-punch indicator: Indicates that it is necessary to align the half-punches
when installing the parts or components.
However, it is not indicated for the half-punches for
improving ease of assembly or preventing erroneous
assembly procedures.
1.4 Servicing Instruments and Tools That
Require Inspection/Calibration
The machine should be installed and serviced by use of servicing instruments and
tools that have been regularly inspected and calibrated as appropriate.
If the machine were serviced using servicing instruments and tools that have not
been inspected and calibrated, proper performance of the machine could not be
guaranteed.
Servicing instruments and tools that require inspection/calibration are as listed below.
The inspection/calibration should be planned and performed in accordance with the
specications and instruction manuals of the applicable servicing instruments and
tools.
Instruments and Tools That Require Inspection/Calibration
Name Inspection Calibration
Dosimeter - 
Steel rule (150 mm) -
Steel rule (300 mm) -
Digital multimeter  
Calipers ()-
: A block gauge for use in inspection requires calibration.
Servicing of the XG2000
- The servicing for the XG2000 is almost the same as that for the XG5000. Only
the servicing operations specic to the XG2000 are described at the end of the
respective service manuals.
- In using the MUTL, read “shelf 1/shelf 2” instead of “shelf 3/shelf 4” for servicing.

CR-IR 362 Service Manual
011-207-08E
09.30.2008 FM5340
0.3
0.3
Safety Precaution
1. Safety Precautions.................................................................. 1
1.1 General Precautions........................................................................1
1.2 Precautions Against Laser Radiation ..............................................2
1.3 Precautions on Patient Environment ...............................................2
2. Labels....................................................................................... 3
2.1 Laser Precaution Labels..................................................................3
2.1.1 Laser Precaution Label Attachment Locations............................................3
2.1.2 List of CR-IR 362 Laser Precaution Labels.................................................4
2.2 Other Labels....................................................................................7
2.2.1 Attachment Locations for Ratings Indication Label and Other Labels ........7
2.2.2 Handling Instruction Labels and Attachment Locations ............................10
3. Protective Housings Against Laser Exposure ................... 14
4. CLASSIFICATION .................................................................. 14
5. Cautions on Electromagnetic Waves .................................. 15
5.1 Electromagnetic Compatibility (EMC)............................................15
5.1.1 Further information for IEC60601-1-2:2001 ..............................................15
CR-IR 362 Service Manual - Contents
Contents Safety Precautions

CR-IR 362 Service Manual
011-207-07E
02.19.2007 FM5097
0.4
0.4
1. SpecicationsofMachine ...................................................... 1
1.1 Product Code ..................................................................................1
1.2 Available IP Sizes and Types ..........................................................1
1.3 List of Optional Items.......................................................................1
1.4 ProductSpecications.....................................................................2
1.5 Dimensions, Weight, and Center of Gravity ....................................2
1.6 Means for Moving and Fixing the Machine......................................3
1.7 Environmental Conditions ...............................................................3
1.8 ElectricalSpecications...................................................................4
1.9 Installation Space and Servicing Space ..........................................4
1.10 Disposal...........................................................................................5
1.10.1 Disposal of Machine....................................................................................5
1.10.2 Disposal of IP..............................................................................................5
ProductSpecications
ContentsProductSpecications

CR-IR 362 Service Manual
0.5
0.5
Contents Machine Description (MD)
011-207-09E
09.30.2009 FM5539
MachineDescription(MD)
1. MachineOverview............................................................ MD-1
1.1 Features ...................................................................................MD-1
1.2 SystemConguration ...............................................................MD-1
1.3 OverallMachineCongurationandComponentNames ..........MD-2
1.4 Machine Components ..............................................................MD-4
1.4.1 Unit Locations ...................................................................................... MD-4
1.4.2 Roller Locations and Conveyance Paths ............................................. MD-5
1.4.3 I/O Locations and Functional Descriptions........................................... MD-6
1.4.4 Board Locations ................................................................................. MD-12
1.5 System Block Diagram ...........................................................MD-13

CR-IR 362 Service Manual
0.6
0.6
Contents Troubleshooting (MT)
011-207-07E
02.19.2007 FM5097
Troubleshooting(MT)
2. Error Code Table .............................................................MT-10

CR-IR 362 Service Manual
0.7
0.7
Contents Service Parts List（SP）
011-207-09E
09.30.2009 FM5539
Service Parts List（SP）
How to Use Service Parts List ...............................................................SP-1
INDEX .................................................................................................SP-2
01A COVER 1 (#20001 or Later)......................................................SP-3
01B COVER 2 (#20001 or Later)......................................................SP-4
01C COVER 3 (#50001 or Later)......................................................SP-5
01D COVER 4 (#50001 or Later)......................................................SP-6
02A FRAME 1...................................................................................SP-7
02B FRAME 2 (#20001 or Later) ......................................................SP-8
02C FRAME 3 (#50001 or Later) ......................................................SP-9
02D FRAME 4.................................................................................SP-10
03A CASSETTE SET UNIT 1 (#20001 or Later) ............................SP-11
03B CASSETTE SET UNIT 2 (#50001 or Later) ............................SP-12
03C CASSETTE SET UNIT 3 (#20001 or Later) ............................SP-13
03D CASSETTE SET UNIT 4 (#50001 or Later) ............................SP-14
03E CASSETTE SET UNIT 5 .........................................................SP-15
03F CASSETTE SET UNIT 6 .........................................................SP-16
03G CASSETTE SET UNIT 7 .........................................................SP-17
04A FEED LOAD CONVEYOR 1 ...................................................SP-18
04B FEED LOAD CONVEYOR 2 ...................................................SP-19
04C FEED LOAD CONVEYOR 3 ...................................................SP-20
04D FEED LOAD CONVEYOR 4 ...................................................SP-21
04E FEED LOAD CONVEYOR 5 ...................................................SP-22
04F FEED LOAD CONVEYOR 6 ...................................................SP-23
04G FEED LOAD CONVEYOR 7 ...................................................SP-24
04H FEED LOAD CONVEYOR 8 ...................................................SP-25
05A SIDE-POSITIONING CONVEYOR 1.......................................SP-26
05B SIDE-POSITIONING CONVEYOR 2.......................................SP-27
05C SIDE-POSITIONING CONVEYOR 3.......................................SP-28
05D SIDE-POSITIONING CONVEYOR 4.......................................SP-29
05E SIDE-POSITIONING CONVEYOR 5 (#20001 or Later)..........SP-30
05F SIDE-POSITIONING CONVEYOR 6 (#50001 or Later)..........SP-31
06A AFTER SCANNING CONVEYOR 1 ........................................SP-32
06B AFTER SCANNING CONVEYOR 2 ........................................SP-33
06C AFTER SCANNING CONVEYOR 3 ........................................SP-34
06D AFTER SCANNING CONVEYOR 4 ........................................SP-35
06E AFTER SCANNING CONVEYOR 5 ........................................SP-36
07A ERASURE CONVEYOR 1 ......................................................SP-37
07B ERASURE CONVEYOR 2 ......................................................SP-38
07C ERASURE CONVEYOR 3 ......................................................SP-39
07D ERASURE CONVEYOR 4 ......................................................SP-40
07E ERASURE CONVEYOR 5 ......................................................SP-41
07F ERASURE CONVEYOR 6 ......................................................SP-42
07G ERASURE CONVEYOR 7 ......................................................SP-43
07H ERASURE CONVEYOR 8 (#20001 or Later)..........................SP-44
07I ERASURE CONVEYOR 9 (#20001 or Later)..........................SP-45
07J ERASURE CONVEYOR 10 (#50001 or Later)........................SP-46
08 SCANNING OPTICS UNIT......................................................SP-47
09 LIGHT-COLLECTING UNIT.....................................................SP-48

CR-IR 362 Service Manual
0.8
0.8
Contents Service Parts List（SP）
011-207-09E
09.30.2009 FM5539
10A SUB SCANNING UNIT 1.........................................................SP-49
10B SUB SCANNING UNIT 2.........................................................SP-50
10C SUB SCANNING UNIT 3.........................................................SP-51
10D SUB SCANNING UNIT 4.........................................................SP-52
10E SUB SCANNING UNIT 5.........................................................SP-53
10F SUB SCANNING UNIT 6.........................................................SP-54
10G SUB SCANNING UNIT 7.........................................................SP-55
10H SUB SCANNING UNIT 8.........................................................SP-56
11A CONTROLLER 1 (#20001 or Later) ........................................SP-57
11B CONTROLLER 2 (#50001 or Later) ........................................SP-58
11C CONTROLLER 3.....................................................................SP-59
12 CABLE.....................................................................................SP-60
13A CIRCUIT DIAGRAM 1 (#20001 or Later) ................................SP-61
13B CIRCUIT DIAGRAM 2 (#50001 or Later) ................................SP-79
14 PARTS NOS. SEARCH TABLE...............................................SP-97
15 TABLE OF SCREWS / WASHERS INDICATIONSYMBOLS .. SP-102
16 LIST OF QUICK WEARING PARTS......................................SP-102
17 OPTION.................................................................................SP-103
18 JIG.........................................................................................SP-104
19 XG2000 .................................................................................SP-105