Fujitsu AUXG45LRLB Original operating manual

SPLIT TYPE
ROOM AIR CONDITIONER
Cassette type
Models Indoor unit Outdoor unit
AUXG30LRLB
AUXG36LRLB
AUXG45LRLB
AUXG54LRLB
AO*G30LBTA
AO*G36LBTA
AO*G45LBTA
INVERTER
SERVICE
INSTRUCTION
R410A
AO*G54LBTA
RCG30LRLB
RCG36LRLB
RCG45LRLB
RCG54LRLB
ROG30LBTA
ROG36LBTA
ROG45LBTA
ROG54LBTA

CONTENTS
1. SPECIFICATIONS
1. DESCRIPTION OF EACH CONTROL OPERATION
1-1 COOLING OPERATION............................................................................................
1-4 AUTO CHANGEOVER OPERATION........................................................................
1-5 INDOOR FAN CONTROL.........................................................................................
1-7 OUTDOOR FAN CONTROL
1-6. AIR FLOW DIRECTION CONTROL...................
......................................................................................
...................................................................
1-8 COMPRESSOR CONTROL......................................................................................
01-01
1-2 HEATING OPERATION............................................................................................. 01-02
1-3 DRY OPERATION...................................................................................................... 01-03
01-04
01-06
01-09
01-11
01-10
1-9 TIMER OPERATION CONTROL............................................................................... 01-13
1-10 ELECTRONIC EXPANSION VALVE CONTROL...................................................... 01-17
1-11 TEST OPERATION CONTROL............................................................................... 01-17
1-12 PREVENT TO START FOR 3 MINUTES (3 MINUTES ST).................................... 01-17
1-13 4-WAY VALVE EXTENSION SELECT.................................................................... 01-17
1-14 AUTO RESTART..................................................................................................... 01-18
1-15 PUMP DOWN.......................................................................................................... 01-18
1-16 COMPRESSOR PREHEATING............................................................................... 01-20
1-17 10°C HEAT OPERATION........................................................................................ 01-20
1-21 VARIOUS PROTECTIONS...................................................................................... 01-24
1-22 LOW NOISE OPERATION ....................................................................................... 01-27
1-24 HUMAN SENSOR(OPTION) ................................................................................... 01-28
1-20 OFF DEFROST OPERATION CONTROL............................................................... 01-23
1-19 DEFROST OPERATION CONTROL....................................................................... 01-21
1-18 ECONOMY OPERATION........................................................................................ 01-20
1-23 PEAK CUT OPERATION ......................................................................................... 01-28
1-25 DRAIN PUMP OPERATION............. ......................................................................... 01-29
2-1 ERROR DISPLAY......................................................................................................
2. TROUBLE SHOOTING
2-2 TROUBLE SHOOTING WITH ERROR CODE..........................................................
2-3 TROUBLE SHOOTING WITH NO ERROR CODE....................................................
2-4 SERVICE PARTS INFORMATION............................................................................
02-01
02-29
02-03
02-34
1-26 DESCRIPTION OF DISPLAY UNIT ......................................................................... 01-30

1 . DESCRIPTION OF EACH
CONTROL OPERATION
R410A
INVERTER
Cassette type

1-1. COOLING OPERATION
1-1-1 COOLING CAPACITY CONTROL
A sensor (room temperature thermistor) built in the indoor unit will usually perceive
difference or variation between a set temperature and present room temperature, and
controls the operation frequency of the compressor.
* If the room temperature is 6.0°C higher than a set temperature,
the compressor operation frequency will attain to maximum performance.
* If the room temperature is 1.0°C lower than a set temperature, the compressor
will be stopped.
* When the room temperature is between +6.0°C to -1.0°C of the setting temperature,
the compressor frequency is controlled within the range shown in Table1.
However, the maximum frequency is limited in the range shown in Fig.1 based on the
fan speed mode and the outdoor temperature.
minimum
frequency
maximum
frequency
16rps 90rps
30,36LBTA
16rps 100rps
45LBTA
16rps 110rps
54LBTA
Hi Me Lo Qu
72rps
65rps
50rps 44rps 39rps
59rps 50rps
50rps 44rps
35rps
39rps
39rps
A zone
B zone
C zone
D-F zone
30,36LBTA
( Table 1 : Compressor Frequency Range )
( Fig. 1 : Limit of Maximum Frequency based on Outdoor Temperature )
01-01
93rps
93rps
78rps
73rps 56rps 47rps
75rps
75rps
68rps
68rps
68rps 56rps
29rps
44rps
44rps
44rps
A zone
B zone
C zone
D-F zone
Fan speed mode
Outdoor air
temperature
A zone
B zone
C zone
D zone
E zone
F zone
When the room
temperature rises
When the room
temperature drops
36°C
32°C
21°C
12°C
2°C
34°C
30°C
19°C
10°C
0°C
45LBTA
72rps 59rps 50rps 39rps
100rps
100rps
85rps
76rps 62rps 50rps
78rps
78rps
73rps
73rps
73rps 62rps
29rps
44rps
44rps
44rps
A zone
B zone
C zone
D-F zone
54LBTA

01-02
1-2. HEATING OPERATION
A sensor (room temperature thermistor) built in the indoor unit will usually perceive
difference or variation between a set temperature and present room temperature, and
controls the operation frequency of the compressor.
* If the room temperature is lower 6.0°C than a set temperature,
the compressor operation frequency will attain to maximum performance.
* If the room temperature is higher 1.0°C than a set temperature, the compressor
will be stopped.
* When the room temperature is between +1.0°C to -6.0°C of the setting temperature,
the compressor frequency is controlled within the range shown in Table2.
( Table 2 : Compressor Frequency Range )
minimum
frequency
maximum
frequency
16rps 90rps
30,36LBTA
16rps 110rps
45,54LBTA
MODEL

1-3. DRY OPERATION
1-3-1 INDOOR UNIT CONTROL
The compressor rotation frequency shall change according to set temperature and room
temperature variation which the room temperature sensor of the indoor unit has detected
as shown in the Table 3.
( Table 3 : Compressor frequency )
( Fig.2 : Compressor Control based on Room Temperature )
01-03
Ts : Setting temperature
Ts+0.5°C
Ts+1.5°C
Operating frequency
39rps
X zone
J
30,36LRLB
zone
0rps
44rps
0rpsY zone
Room Room
temperature temperature
X zone
J zone
Y zone
Ts-1.5°C
Ts-0.5°C
( Fig.3 : Indoor Fan Control )
10 30 60 360 120 360 120 10 30 (sec)
OFF
S-Lo
Lo
OFF
Setting air flow
Compressor
ON
45,54LRLB

1-4. AUTO CHANGEOVER OPERATION
01-04
When the air conditioner is set to the Auto mode by remote controller, operation starts in the optimum
mode from among the Heating, Cooling, and Monitoring mode. During operation, the
optimum mode is automatically switched in accordance with temperature changes. The temperature
can be set between 18°C and 30°C in 0.5°C (wireless and 2WIRE remote controller)
Or 1.0°C(3WIRE remote controller) steps.
When operation starts, indoor fan and outdoor fan are operated for around 1 minutes.
Room temperature and outdoor temperature are sensed, and the operation mode is selected
in accordance with the table below. <Monitoring mode>
( Table 4 : Operation mode selection table )
Room temperature (TR)
TR> Ts+2°C
Ts+2°C TR Ts -2°C *Middle zone
TR < Ts -2°C Heating
When the compressor was stopped for 6 consecutive minutes by the temperature control function
after the Cooling or Heating mode was selected at above, operation is switched
to Monitoring and the operation mode is selected again.
When the middle zone is selected on the predetermining of the operation mode, the operation mode
before the changing to the monitor mode is selected.
1
2
3
1
( Fig.4 : Outdoor temperature zone selection )
Cooling
Operation mode
Temperature
25°C and over
25°C under Heating
Cooling
Mode
*If it's Middle zone, operation mode of indoor unit is selected as below.
(1). Same operation mode is selected as outdoor unit.
If outdoor unit is operating in Cooling and Heating mode,
indoor unit will be operated by the same operation mode.
(2). Selected by the outdoor temperature.
If outdoor unit is operating in other than Cooling and Heating mode, indoor unit will be operated
according to the outdoor temperature as below.
TR : Room temperature
Ts : Setting temperature

01-05
START
Room temp.
Ts+2°C?
COOLING OPERATIONHEATING OPERATION
YES
Auto change over is
second or more?
NO
NO
YES
NO
NO
AUTO CHANGEOVER operation flow chart
TS: Setting temperature
Room temp.
Ts -2°C?
Thermostat remains
in OFF state for 6 minutes or
longer?
System stops
or operation command other than
auto changeover operation?
NO
Thermostat remains
in OFF state for 6 minutes or
longer?
System stops
or operation command other than
auto changeover operation?
Middle zone
NO
NO
Operation mode of
outdoor unit : Cooling?
YES
NO
Operation mode of outdoor unit
: Heating?
YES
NO
YES
Outdoor temperature<
25°C?
NO
YES
YES
YES
NO
YES
YES
Operation mode
before the monitor mode is
cooling mode?
Monitor mode

1-5. INDOOR FAN CONTROL
1. Fan speed
( Table 5 : Standard of Indoor Fan Speed )
2. FAN OPERATION
*The following fan speed is a standard value.
The airflow can be switched in 5 steps such as AUTO, QUIET, LOW, MED, HIGH, while the indoor
fan only runs.
When [AUTO] is selected, the indoor Fun motor runs MED.
01-06
Operation
mode Air flow mode
HIGH
MED+
LOW
Heating
Quiet
Cooling
560
420
300
420
270
470
530
660
430
660
560
510
430
300
430
270
510
600
700
470
700
590
530
470
300
470
270
530
630
HIGH
MED
LOW
Quiet
*Soft Quiet
S-Lo
FAN
Dry
3. COOLING OPERATION
Switch the airflow [AUTO], and the indoor fan motor will run according to a room temperature,
as shown in Fig.5.
On the other hand, if switched in [HIGH] ~ [LOW], the indoor motor will run at a constant airflow of [COOL]
operation modes LOW, MED, HIGH,as shown in Table 5.
( Fig.5 : Airflow change - over ( Cooling : AUTO ) )
When the room
temperature rises
When the room
temperature drops
TR : Room temperature
Ts : Setting temperature
TR-Ts > 2°C
=
1°C > TR-Ts
2°C > TR-Ts > 1°C
=
TR-Ts > 2.5°C
=
1.5°C > TR-Ts
2.5°C > TR-Ts > 1.5°C
=
HIGH mode
MED mode
LOW mode
*1
*1 : Contains a condition to the following
When the operation mode is set to AUTO mode
at the start of operation.
When the setting temperature was changed.
When the operation mode was changed to COOLING mode.
When the airflow mode was changed to AUTO mode.
Speed (rpm)
30LRLB 36LRLB 45LRLB
560
420
470
510
MED 510 560 590
Cool air prevention 300 300 300
54LRLB
740
480
740
630
570
480
300
480
270
570
680
630
300
*Note, during Economy operation and operation mode is FAN, the air flow is 1 step downs.
(Hi > Me, Me > Lo, Lo > Quiet, Quiet > Soft Quiet)

4. HEATING OPERATION
Switch the airflow [AUTO], and the indoor fan motor will run according to a room temperature,
as shown in Fig.6.
On the other hand, if switched in [HIGH] ~ [LOW], the indoor motor will run at a constant airflow
of [HEAT] operation modes LOW, MED, HIGH as showin in the Table 5.
6. DRY OPERATION
Refer to the Table 5
During the dry mode operation, the fan speed setting can not be changed.
01-07
Indoor heat exchanger
temperature
( Fig.6 : Airflow change - over ( Heating : AUTO ) )
TR-Ts > -1.0°C
=
-2.0°C > TR-Ts
1.0°C > TR-Ts > -2.0°C
=
TR-Ts > -1.5°C
=
-2.5°C > TR-Ts
-1.5°C > TR-Ts > -2.5°C
=
LOW mode
MED mode
HIGH mode
5. COOL AIR PREVENTION CONTROL (Heating mode)
The maximum value of the indoor fan speed is set as shown in Fig.7, based on the detected
temperature by the indoor heat exchanger sensor on heating mode.
When the compressor does not operate, the indoor fan motor operates [S-Lo] or [Stop] mode.
( Fig.7 : Cool Air Prevention Control )
Cool air
prevention
S-Lo
42°C
30°C
34°C
Indoor heat exchanger
temperature rises Indoor heat exchanger
temperature drops
Hi
*Me+
or setting fan mode
*Lo
or setting fan mode
*Lo
or setting fan mode
*Lo
or setting fan mode
39°C
37°C
37°C
32°C
24°C
*Lower speed is selected.
42°C
30°C
34°C
Indoor heat exchanger
temperature rises Indoor heat exchanger
temperature drops
Hi
*Me+
or setting fan mode
*Lo
or setting fan mode
39°C
37°C
37°C
32°C
24°C
*Lower speed is selected.
13 min. later