Fujitsu Inverter 9318657012 User manual

KEEP THIS OPERATION MANUAL
FOR FUTURE REFERENCE
FUJITSU GENERAL LIMITED
OPERATING MANUAL
PART No.9318657012
ROOM AIR CONDITIONER
COMPACT WALL
MOUNTED TYPE
R410A
REFRIGERANT
This Air Conditioner contains and
operates with refrigerant R410A.
THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED
BY QUALIFIED PERSONNEL.
Refer to Commonwealth, State, Territory and local legislation,
regulations, codes, installation & operation manuals, before
the installation, maintenance and/or service of this product.
9318657012_OM_EN.indd 1 7/31/2012 10:36:23 AM

2
SAFETY PRECAUTIONS
●Before using the appliance, read these “PRECAUTIONS” thoroughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain safe operating conditions.
●“DANGER”, “WARNING” and “CAUTION” have the following meanings in these instructions:
DANGER This mark indicates procedures which, if improperly performed, are most likely to result in
the death or serious injury to the user or service personnel.
WARNING This mark indicates procedures which, if improperly performed, might lead to the death or
serious injury of the user or service personnel.
CAUTION This mark indicates procedures which, if improperly performed, might possibly result in
personal harm to the user, or damage to property.
●Do not attempt to install this air conditioner by yourself.
●This air conditioner contains no user-serviceable parts. Always consult authorized service personnel for
repairs.
●
When moving, consult authorized service personnel for disconnection and installation of the air conditioner.
●
Do not become excessively chilled by staying for many hours in the direct cooling airow.
●Do not insert ngers or objects into the outlet port or intake grille.
●Do not start and stop air conditioner operation by disconnecting the power supply cord.
●Take care not to damage the power supply cord.
●
If the power supply cord of this appliance is damaged, it should only be replaced by the authorized service
personal, since special purpose tools and specied cord are required.
●In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the breaker, and
consult authorized service personnel.
●In the event of refrigerant leakage, be sure to keep away from re or any ammables. (consult an autho-
rized service personnel)
●Provide occasional ventilation during use.
●Do not direct airow at replaces or heating apparatus.
●Do not climb on, or place objects on, the air conditioner.
●Do not hang objects from the indoor unit.
●Do not set ower vases or water containers on top of air conditioners.
●Do not place any other electrical products or household belongings under indoor unit or outdoor unit.
Dripping condensation from the unit might get them wet, and may cause damage or malfunction of your
property.
●Do not expose the air conditioner directly to water.
●Do not operate the air conditioner with wet hands.
●Do not pull power supply cord.
●Turn off power supply when not using the indoor unit for extended periods.
●Check the condition of the installation stand for damage.
●Do not place animals or plants in the direct path of the airow.
●Do not drink the water drained from the air conditioner.
●Do not use in applications involving the storage of foods, plants or animals, precision equipment, or art
works.
●Do not touch the aluminum ns of heat exchanger built-in the indoor or outdoor unit to avoid personal
injury when you install or maintain the unit.
DANGER
CAUTION
CONTENTS
SAFETY PRECAUTIONS..................................... 2
FEATURES AND FUNCTIONS ............................ 3
NAME OF PARTS ................................................ 4
PREPARATION .................................................... 6
OPERATION......................................................... 7
TIMER OPERATION ............................................ 9
SLEEP TIMER OPERATION................................ 10
ADJUSTING THE DIRECTION OF AIR
CIRCULATION ..................................................... 11
SWING OPERATION ........................................... 12
ECONOMY OPERATION ..................................... 12
MANUAL AUTO OPERATION.............................. 13
OPERATING TIPS................................................ 13
CLEANING AND CARE........................................ 14
TROUBLESHOOTING ......................................... 16
9318657012_OM_EN.indd 2 7/31/2012 10:36:47 AM

3
FEATURES AND FUNCTIONS
Energy saving and Comfortable function
INVERTER
At the start of operation, large amount of power is used to
bring the room quickly to the desired temperature. Afterward,
the air conditioner automatically switches to a low power set-
ting for economic and comfortable operation.
ECONOMY OPERATION
When ECONOMY operation mode is operated, the room tem-
perature will be little higher than the set-temp under cooling
mode. Therefore, the ECONOMY mode is able to save more
energy than other normal mode.
SWING OPERATION
The Airflow Direction Louvers swings automatically up and
down so that the air speeds to every nook and corner of your
room.
AUTO CHANGEOVER
The operation mode (cooling and dry) is switched automati-
cally to maintain the set temperature, and the temperature is
kept constant at all times.
SUPER QUIET OPERATION
The indoor unit’s airow is reduced to produce quieter operation.
Convenient function
PROGRAM TIMER
The program timer allows you to integrate OFF timer and ON
timer operations in a single sequence. The sequence can
involve 1 transition from OFF timer to ON timer, or from ON
timer to OFF timer, within a 24 hour period.
SLEEP TIMER
When the SLEEP button is pressed during cooling mode, the
temperature setting is gradually raised during the period of
operation. When the set time is reached, the indoor unit auto-
matically turns off.
Clean function
REMOVABLE INTAKE GRILLE
The indoor unit’s Intake Grille can be removed for easy clean-
ing and maintenance.
MILDEW-RESISTANT FILTER
The Air Filter has been treated to resist mildew growth, thus al-
lowing cleaner use and easier care.
Anti-Bacterial Air Cleaning Filter
The lter catches airborne fungi, bacteria, and smell.
The components in the lter suppress the growth of the fungi
and bacteria that have been caught.
 Remote controller
WIRELESS REMOTE CONTROLLER
The Wireless Remote Controller allows convenient control of
indoor unit operation.
WIRED REMOTE CONTROLLER (OPTION)
The optional wired remote controller can be used.
When you use remote controller, there are following different
points as compared with using wireless remote controller.
[The additional functions for wired ones]
• Weekly timer
• Temperature set back timer
And you can use both wired and wireless remote controller
simultaneously.
(But function is limited)
When the restricted functions on the remote controller are
used, beeping sound will be heard, OPERATION, TIMER and
the 3rd lamp of the indoor unit will ash.
[The restricted functions for wireless ones]
• SLEEP TIMER
• TIMER
●Do not apply any heavy pressure to radiator ns.
●Operate only with air lters installed.
●Do not block or cover the intake grille and outlet port.
●Ensure that any electronic equipment is at least 3.3ft (1m) away from either the indoor or outdoor units.
●Avoid installing the air conditioner near a replace or other heating apparatus.
●
When installing the indoor and outdoor unit, take precautions to prevent access to infants.
●Do not use inammable gases near the air conditioner.
●This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
CAUTION
SAFETY PRECAUTIONS
9318657012_OM_EN.indd 3 7/31/2012 10:36:48 AM

4
Fig. 1
NAME OF PARTS
Fig. 5
To facilitate explanation, the accompanying illustra-
tion has been drawn to show all possible indicators; in
actual operation, however, the display will only show
those indicators appropriate to the current operation.
Fig. 6
Fig. 2
Fig. 3
Fig. 4
9318657012_OM_EN.indd 4 7/31/2012 10:36:48 AM

5
Fig. 1 Indoor Unit
1Operating Control Panel (Fig. 2)
2MANUAL AUTO button
●When the MANUAL AUTO button is
pressed in for more than 10 seconds, the
forced cooling operation will start.
●The forced cooling operation is used at
the time of installation.
Only for authorized service personnel's
use.
●When the forced cooling operation starts
by any chance, press the START/STOP
button to stop the operation.
●Please press the button at FILTER IN-
DICATOR RESET
3Indicator (Fig. 3)
4Remote Control Signal Receiver
5OPERATION Indicator Lamp (green)
6TIMER Indicator Lamp (orange)
●If the TIMER indicator lamp ashes when
the timer is operating, it indicates that a
fault has occurred with the timer setting
(See page 13 “AUTO Restart”.)
7ECONOMY Indicator Lamp (green)
●ECONOMY indicator lamp lights when
ECONOMY OPERATION is operating.
8SUPER QUIET Indicator Lamp (green)
9Intake Grille (Fig. 4)
0Front Panel
AAir Filter
BAirow Direction Louver
CRight-Left Louver
(behind Airow Direction Louver)
DDrain Hose
EAir Cleaning Filter
FRemote Controller (Wired/Option)
Fig. 5 Remote Controller
GSignal Transmitter
HMODE button
IECONOMY button
JSLEEP button
KTIMER MODE button
LFAN button
MSTART/STOP button
NSET button (Vertical)
OSWING button
PSET TEMP. button ( / )
QTIMER SET ( / ) button
RCLOCK ADJUST button
STEST RUN button
●This button is used when installing the air
conditioner, and should not be used un-
der normal conditions, as it will cause the
indoor unit’s thermostat function to oper-
ate incorrectly.
●If this button is pressed during normal op-
eration, the indoor unit will switch to test
operation mode, and the Indoor Unit’s
OPERATION Indicator Lamp and TIMER
Indicator Lamp will begin to ash simulta-
neously.
●To stop the test operation mode, press
the START/STOP button to stop the air
conditioner.
TRESET button
URemote Controller Display (Fig.6)
VTemperature SET Display
WOperation Mode Display
XSLEEP TIMER Display
YTransmit Indicator
ZFan Speed Display
[SWING Display
\Timer Mode Display
]Clock Display
NAME OF PARTS
9318657012_OM_EN.indd 5 7/31/2012 10:36:49 AM

6
PREPARATION
CAUTION
●Take care to prevent infants from acciden-
tally swallowing batteries.
●When not using the Remote Controller for
an extended period, remove the batteries to
avoid possible leakage and damage to the
unit.
●If leaking battery uid comes in contact
with your skin, eyes, or mouth, immediately
wash with copious amounts of water, and
consult your physician.
●Dead batteries should be removed imme-
diately and disposed of properly, either in a
battery collection receptacle or to the appro-
priate authority.
●Do not attempt to recharge dry batteries.
Never mix new and used batteries, or
batteries of different types.
Batteries should last about 1 year under
normal use. If the Remote Controller's
operating range becomes appreciably
reduced, replace the batteries and press
the RESET button with the tip of a ball-
point pen or other small object.
Load Batteries (AAA/R03/LR03 ×2)
1Press and slide the battery compartment lid on the
reverse side to open it.
Slide in the direction of the arrow while pressing the mark.
2Insert batteries.
Be sure to align the battery polarities ( ) correctly.
3Close the battery compartment lid.
Set the Current time
1Press the CLOCK ADJUST button (Fig. 5 R).
Use the tip of a ball-point pen or other small object to press the button.
2Use the TIMER SET ( / ) buttons (Fig. 5 Q) to
adjust the clock to the current time.
button: Press to advance the time.
button: Press to reverse the time.
(Each time the buttons are pressed, the time will be advanced/reversed in
1-minute increments; hold the buttons depressed to change the time quickly
in 10-minute increments.)
3Press the CLOCK ADJUST button (Fig. 5 R) again.
This completes the time setting and starts the clock.
To Use the Remote Controller
●The Remote Controller must be pointed at signal receiver (Fig. 3 4) to operate cor-
rectly.
●Operating Range: About 7 m.
●When a signal is properly received by the indoor unit, a beeping sound will be heard.
●If no beep is heard, press the Remote Controller button again.
Remote Controller Holder
1 Mount the Holder.
Screws
Turn on the Power
1Turn on the circuit breaker
2 Set the Remote Controller.
Insert
Press in
3 To remove the Remote Con-
troller (when use at hand).
Slide up
Pull out
9318657012_OM_EN.indd 6 7/31/2012 10:36:49 AM

7
OPERATION
Example: When set to COOL.
Example: When set to 26 °C.
Example: When set to AUTO.
▲ ▲ ▲ ▲ ▲
To Select Mode Operation
1Press the START/STOP button (Fig.5 M).
The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3 5) will light.
The air conditioner will start operating.
2Press the MODE button (Fig.5 H) to select the de-
sired mode.
Each time the button is pressed, the mode will change in the following order.
AUTO COOL DRY FAN
About 3 seconds later, the entire display will reappear.
To Set the Thermostat
Press the SET TEMP. button (Fig. 5 P).
button: Press to raise the thermostat setting.
button: Press to lower the thermostat setting.
Thermostat setting range:
AUTO ....................................18–30 °C
Cooling/Dry ...........................18–30 °C
The thermostat cannot be used to set room temperature during the FAN mode (the tem-
perature will not appear on the Remote Controller's Display).
About 3 seconds later, the entire display will reappear.
The thermostat setting should be considered a standard value, and may differ
somewhat from the actual room temperature.
To Set the Fan Speed
Press the FAN button (Fig. 5 L).
Each time the button is pressed, the fan speed changes in the following order:
AUTO HIGH MED LOW QUIET
About 3 seconds later, the entire display will reappear.
When set to AUTO:
Cooling
: As the room temperature approaches that of the thermostat setting, the
fan speed becomes slower.
Fan : The fan runs at the low fan speed.
The fan will operate at a very low setting during Monitor operation.
SUPER QUIET Operation
When set to quiet.
SUPER QUIET indicator Lamp (green) (Fig.3 8) will light.
SUPER QUIET operation begins. The indoor unit’s airow will be reduced for quieter
operation.
●SUPER QUIET operation cannot be used during Dry mode. (The same is true when
dry mode is selected during AUTO mode operation.)
●During Super Quiet operation, Cooling performance will be reduced somewhat. If the
room does not cool down when using SUPER QUIET Operation, please adjust the
indoor unit’s Fan Speed.
To Stop Operation
Press the START/STOP button (Fig. 5 M).
The OPERATION Indicator Lamp (green) (Fig. 3 5) will go out.
▲ ▲ ▲ ▲
9318657012_OM_EN.indd 7 7/31/2012 10:36:50 AM

8
About AUTO CHANGEOVER Operation
AUTO: ●When AUTO CHANGEOVER operation rst selected, the fan will operate
at very low speed for about a few minutes, during which time the indoor
unit detects the room conditions and selects the proper mode.
Room temperature is higher than the dened temperature in temperature
setting oCooling mode or dry mode
Room temperature is close to or lower than the dened temperature in
temperature setting oMonitor operation
●When the indoor unit has adjusted your room’s temperature to near the
temperature setting, it will begin monitor operation. In the monitor opera-
tion mode, the fan will operate at low speed. If the room temperature
subsequently changes, the indoor unit will once again select the appropri-
ate operation (Cooling) to adjust the temperature to the value set in the
temperature setting.
●If the mode automatically selected by the unit is not what you wish, select
one of the mode operation (COOL, DRY, FAN).
About Mode Operation
Cooling: ●Use to cool your room.
Dry: ●Use for gently cooling while dehumidifying your room.
●During Dry mode, the indoor unit will operate at low speed; in order to ad-
just room humidity, the indoor unit’s fan may stop from time to time. Also,
the fan may operate at very low speed when adjusting room humidity.
●The fan speed cannot be changed manually when Dry mode has been
selected.
Fan: ●Use to circulate the air throughout your room.
During Cooling/Dry mode:
Set the thermostat to a temperature setting
that is lower than the present room tem-
perature. The Cooling and Dry modes will
not operate if the thermostat is set higher
than the actual room temperature (in Cool-
ing mode, the fan alone will operate).
During Fan mode:
You can not use the indoor unit to cool your
room.
OPERATION
Dened
temperature in
temperature
setting
Cooling mode
or Dry mode
Monitor operation
9318657012_OM_EN.indd 8 7/31/2012 10:36:50 AM

9
TIMER OPERATION
Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞P. 5).
To Use the ON timer or OFF timer
1Press the START/STOP button (Fig. 5 M)
(if the indoor unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3
5
) will light.
2Press the TIMER MODE button (Fig. 5 K) to select the
OFF timer or ON timer operation.
Each time the button is pressed the timer function changes in the following
order:
CANCEL OFF ON
PROGRAM (OFF
oON, OFF mON)
The indoor unit’s TIMER Indicator Lamp (orange) (Fig. 3
6
) will light.
3Use the TIMER SET buttons (Fig. 5 Q) to set the de-
sired OFF time or ON time.
Set the time while the time display is ashing (the ashing will continue for
about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To Use the Program timer
1Press the START/STOP button (Fig. 5 M)
(if the indoor unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3
5
) will light.
2Set the desired times for OFF timer and ON timer.
See the section “To Use the ON timer or OFF timer” to set the desired mode
and times.
About 3 seconds later, the entire display will reappear.
The indoor unit’s TIMER Indicator Lamp (orange) (Fig. 3 6) will light.
3Press the TIMER MODE button (Fig. 5 K) to select the
PROGRAM timer operation (OFF ON or OFF ON
will display).
The display will alternately show “OFF timer” and “ON timer”, then change to
show the time setting for the operation to occur rst.
●
The program timer will begin operation. (If the ON timer has been selected
to operate rst, the indoor unit will stop operating at this point.)
About 5 seconds later, the entire display will reappear.
About the Program timer
●The program timer allows you to integrate OFF timer and ON timer operations in a
single sequence. The sequence can involve 1 transition from OFF timer to ON timer,
or from ON timer to OFF timer, within a 24 hour period.
●The rst timer function to operate will be the 1 set nearest to the current time. The
order of operation is indicated by the arrow in the Remote Controller's Display
(OFF  ON, or OFF  ON).
●One example of Program timer use might be to have the air conditioner automati-
cally stop (OFF timer) the operation after you go to sleep, then start (ON timer) the
operation automatically in the morning before you arise.
To Cancel the Timer
Use the TIMER button to select “CANCEL”.
The indoor unit will return to normal operation.
To Change the Timer Settings
Perform steps 2and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting and waiting until the entire display
reappears, then press the appropriate buttons
to change the operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select “CAN-
CEL”.
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
1. Follow the instructions given in the section “To
Use the ON Timer or OFF Timer” to select
the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF ON.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting, SUPER
QUIET mode), after making the timer setting
and waiting until the entire display reappears,
then press the appropriate buttons to change
the operating condition desired.
▲ ▲ ▲
▼
9318657012_OM_EN.indd 9 7/31/2012 10:36:51 AM

10
SLEEP TIMER OPERATION
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operation is stopped.
To Use the SLEEP Timer
While the air conditioner is operating or stopped, press the
SLEEP button (Fig. 5 J).
The indoor unit’s OPERATION Indicator Lamp (green) (Fig. 3 5) lights and the TIMER
Indicator Lamp (orange) (Fig. 3 6) light.
To Change the Timer Settings
Press the SLEEP button (Fig. 5 J) once again and set the
time using the TIMER SET ( / ) buttons (Fig. 5 Q).
Set the time while the Timer Mode Display is ashing (the ashing will continue about
5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To Cancel the Timer:
Use the TIMER MODE button to select “CAN-
CEL”.
The air conditioner will return to normal opera-
tion.
To Stop the Air Conditioner During
Timer Operation:
Press the START/STOP button.
About the SLEEP Timer
To prevent excessive cooling during sleep, the SLEEP timer function automatically modies the thermostat setting in accordance
with the set time setting. When the set time has elapsed, the air conditioner completely stops.
During Cooling/Dry operation:
When the SLEEP timer is set, the thermostat setting is automatically raised 1 °C every 1 hour. When the thermostat setting is raised
a total of 2 °C, the thermostat setting at that time is maintained until the set time elapses, at which time the air conditioner automati-
cally turns off.
SLEEP timer setting
Set time
1 hour
1 °C 2 °C
9318657012_OM_EN.indd 10 7/31/2012 10:36:51 AM

11
Vertical Air Direction Adjustment
Press the SET button (Fig. 5 N).
Each time the button is pressed, the air direction range will change as follows:
1
2 3 4 5 6
Types of Airow Direction Setting:
1, 2, 3 : During Cooling/Dry modes
1, 2, 3, 4, 5, 6 : During Fan mode
The Remote Controller's display does not change.
●Use the air direction adjustments within the ranges shown above.
●The vertical airow direction is set automatically as shown, in accordance with the
type of operation selected.
During Cooling/Dry mode
: Horizontal ow 1
●During AUTO mode operation, for the rst a few minutes after beginning operation,
airow will be horizontal 1; the air direction cannot be adjusted during this period.
Right-Left Adjustment
Adjust the Right-Left louvers.
Move the Right-Left louvers to adjust airow in the direction you prefer.
ADJUSTING THE DIRECTION OF AIR CIRCULATION
Vertical (up-down) direction of airow is adjusted by pressing the Remote Controller's SET button. Horizontal (right-left) airow direc-
tion is adjusted manually, by moving the Airow Direction Louvers.
Whenever making horizontal airow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are
stopped.
DANGER
Never place ngers or foreign objects inside
the outlet ports, since the internal fan operates
at high speed, and personal injury could be
caused.
●Always use the Remote Controller's
SET button to adjust the vertical airow
louvers. Attempting to move them
manually could result in improper
operation; in this case, stop operation
and restart. The louvers should begin to
operate properly again.
●During use of the Cooling and Dry
modes, do not set the Airow Direction
Louvers in range (4–6) for many hours,
since water vapor may condense near
the outlet louvers and drops of water
may drip from the indoor unit. During the
Cooling and Dry modes, if the Airow
Direction Louvers are left in range 4–6
for more than 30 minutes, they will
automatically return to position 3.
●When used in a room with infants,
children, elderly or sick persons, the
airow direction and room temperature
should be considered carefully when
making settings.
CAUTION
When adjusting the Right-Left Louvers, it
is necessary to stop the Vertical (up-down)
louvers first and make sure that it stops
completely before adjusting the direction.
knob
(two places) Right-Left Louvers
Knob
about 0~65°
about 35~65 °
about 0~20 °
9318657012_OM_EN.indd 11 7/31/2012 10:36:51 AM

12
ECONOMY OPERATION
Begin Air Conditioner operation before performing this procedure.
To Use the ECONOMY Operation
Press the ECONOMY button (Fig.5 I).
The ECONOMY indicator Lamp (green) will light.
ECONOMY operation begins.
To Stop the ECONOMY Operation
Press the ECONOMY button (Fig.5 I) again.
The ECONOMY Indicator Lamp (green) (Fig. 3 7) will go out.
Normal operation begins.
About ECONOMY Operation
At the maximum output, ECONOMY Operation is approximately 70% of normal air conditioner operation for cooling.
● If the room is not cooled well during ECONOMY operation, select normal operation.
● During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if
ECONOMY operation is selected by pressing the ECONOMY operation button.
● When ECONOMY operation mode is operated, the room temperature will be little higher than the set-temp under cooling mode.
Therefore, the ECONOMY mode is able to save more energy than other normal mode.
SWING OPERATION
Begin air conditioner operation before performing this procedure.
To select SWING Operation
Press the SWING button (Fig. 5 O).
The SWING Display (Fig. 6 [) will light.
In this mode, the Airow Direction Louvers will swing automatically to direct the airow
both up and down.
To stop SWING Operation
Press the SWING button (Fig. 5 O) once again.
The SWING Display (Fig. 6 [) will go out.
Airow direction will return to the setting before swing was begun.
About Swing Operation
During cooling/Dry mode : Swings between 1 and 3.
The SWING operation may stop temporarily when the air conditioner’s fan is not operating, or when operating at very low speeds.
● Indicator Lamp
OPERATION
ECONOMY
SUPER QUIET
TIMER
: Lighting : OFF
9318657012_OM_EN.indd 12 7/31/2012 10:37:57 AM

13
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the Remote Controller is lost or otherwise unavailable.
How To Use the Main Unit Controls
Press the MANUAL AUTO button (Fig. 2 2) more than 3 sec-
onds and less than 10 seconds on the main unit control panel.
To stop operation, press the MANUAL AUTO button (Fig. 2 2) for 3 seconds.
●When the air conditioner is operated
by the controls on the MANUAL AUTO
button, it will operate under the same
mode as the AUTO mode selected on
the Remote Controller (see page 8).
●The fan speed selected will be “AUTO”
and the thermostat setting will be stan-
dard (24 °C).
OPERATING TIPS
Temperature and Humidity Range
Permissible ranges of temperature and humidity are as follows:
Cooling/Dry Operation Indoor temperature About 18 °C to 32 °C
Indoor humidity Below approximately 80%.
If the air conditioner is used continuously for
many hours, water may condense on the sur-
face and drip.
If the unit is used under higher temperature conditions than those noted here, the automatic protection circuit may operate, interrupting the operation.
If the unit is used under lower temperature conditions than those noted here, the heat exchanger may freeze, causing water leakage
or other malfunction.
●Do not use the air conditioner for any purpose other than cooling or drying room, or fan.
AUTO Restart
In Event of Power Interruption
●The power supply to the air conditioner is stopped by a power interruption. The air conditioner will then restart automatically in its
previous mode when the power is restored.
●
If a power interruption occurs during TIMER operation, the timer will be reset and the indoor unit will begin (or stop) operation at the new
time setting. In the event that this kind of timer fault occurs, the TIMER Indicator Lamp will ash (See page 4.)
●Use of other electrical appliances (electric shaver, etc.) or nearby use of a wireless radio transmitter may cause the air conditioner
to malfunction. In this event, temporarily turn off the circuit breaker, turn it on and then use the Remote Controller to resume op-
eration.
9318657012_OM_EN.indd 13 7/31/2012 10:38:01 AM

14
●Before cleaning the unit, be sure to stop the unit.
●Turn off the electrical breaker.
●When removing or replacing the air lters, be sure not to touch the heat exchanger, as personal
injury may result.
CAUTION!
Cleaning the Air Filter
1. Open the Intake Grille, and remove the air lter.
Lift up the air lter’s handle, disconnect the two lower tabs, and pull out.
2. Remove dust with a vacuum cleaner or by washing.
After washing, allow to dry thoroughly in a shaded place.
3. Replace the Air Filter and close the Intake Grille.
1Align the sides of the air lter with the panel, and push in fully, making sure the two lower tabs are returned properly to their
holes in the panel.
2Close the Intake Grille.
(For purposes of example, the illustration shows the indoor unit without Intake Grille installed.)
●Dust can be cleaned from the air lter either with a vacuum cleaner, or by washing the lter in a solution of neutral detergent and
warm water. If you wash the lter, be sure to allow it to dry thoroughly in a shady place before reinstalling.
●If dust is allowed to accumulate on the air lter, airow will be reduced, lowering operating efciency and increasing noise.
●During periods of normal use, the Air Filters should be cleaned every two weeks.
●Don't operate the air conditioner with being opened the intake grille.
●When used for extended periods, the indoor unit may accumulate dust inside, reducing its performance. We recommend that
the indoor unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized
service personnel.
●When cleaning the indoor unit’s body, do not use water hotter than 40 °C, harsh abrasive cleansers, or volatile agents like
benzene or thinner.
●Do not expose the indoor unit’s body to liquid insecticides or hairsprays.
●When shutting down the indoor unit for one month or more, rst allow the fan mode to operate continuously for about one-half
day to allow internal parts to dry thoroughly.
CLEANING AND CARE
1
122
handle Air lter (Right & Left)
Hooks (two places)
Hooks (two places)
9318657012_OM_EN.indd 14 7/31/2012 10:38:01 AM

15
CLEANING AND CARE
2. Remove the air cleaning lters attached
to the frames of the front panel.
3. Replace them by two new Air cleaning
lters.
1Remove the old air cleaning lters in reverse order of
their installation.
2Install in the same way as for installation of the air
cleaning lter set.
4. Install the two Air lters and close the
Intake Grille.
● Don't operate the air conditioner with being opened the
intake grille.
About the Air Cleaning Filters
AIR CLEANING FILTER (Two sheet)
●The Air Cleaning Filters are disposable lters. (They can
not be washed and reused.)
●For storage of the Air Cleaning Filters, use the lters as
soon as possible after opening the package.
(The air cleaning effect decreases when the lters are left in
the opened package)
●In order to maintain the air cleaning effect, it is recommend-
ed to replace the lter every 3 years.
Please buy designed air cleaning lters (UTR-FA16-3) (Sold
separately) to exchange the used dirty air cleaning lter
.
Maintenance of Air Cleaning Filters
In order to maintain the air cleaning effect, please clean the
lter in the follow way once six months.
1Remove the air cleaning lter.
2Clean with water and dry in the air.
1) Flush the lter with fresh or warm water. Please ush
with diluted neutral detergent when extremely dirty.
Never wash by reaming or rubbing, otherwise it
will damage the deodorizing effect.
2) Rinse with water ow.
3) Dry in shade.
3Reinstall the air cleaning lter.
Air Cleaning Filter Installation
1. Open the Intake Grille and remove the
Air lters.
2. Attach the air cleaning lter to the frame
of the front panel.
●Attach the lter on the inside of the tabs (7 places) so
as not to stick out.
(In the above gure, the intake grille is omitted for the
explanation)
3. Install the two Air lters and close the
Intake Grille.
●Don't operate the air conditioner with being opened
the intake grille.
●When air cleaning lters are used, the effect will increased
by setting the fan speed to “High”.
Replacing dirty Air cleaning lters
Replace lters with the following components (purchased
separately).
●
AIR CLEANING FILTER : UTR-FA16-3
1. Open the Intake Grille and remove the
Air lters.
Tabs (6 places)
Air cleaning lter frame
Tabs (7 places)
Tabs (7 places)
Air Cleaning Filter
Air cleaning lter frame
Air cleaning lter frame
9318657012_OM_EN.indd 15 7/31/2012 10:38:21 AM

16
TROUBLESHOOTING
In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical
breaker and consult authorized service personnel.
Merely turning off the unit’s power switch will not completely disconnect the unit from the power source.
Always be sure to turn off the electrical breaker to ensure that power is completely off.
Before requesting service, perform the following checks:
Symptom Problem See page
NORMAL
FUNCTION
Doesn’t operate
immediately:
●If the indoor unit is stopped and then immediately started again,
the compressor will not operate for about 3 minutes, in order to
prevent fuse blowouts.
●
Whenever the electrical breaker is turned off then on again the
protection circuit will operate for about 3 minutes, preventing unit
operation during that period.
—
Noise is heard: ●
During operation or immediately after stopping the unit, the sound
of water owing in the air conditioner’s piping may be heard. Also,
noise may be particularly noticeable for about 2 to 3 minutes after
starting operation (sound of refrigerant owing).
●During operation, a slight squeaking sound may be heard. This is
the result of minute expansion and contraction of the front panel
due to temperature changes.
—
Smells: ●Some smell may be emitted from the indoor unit. This smell is the
result of room smells (furniture, tobacco, etc.) which have been
taken into the indoor unit.
—
Mist or steam is emitted: ●During Cooling or Dry operation, a thin mist may be seen emitted
from the indoor unit. This results from the sudden Cooling of room
air by the cool air emitted from the indoor unit, resulting in con-
densation and misting.
—
Airow is weak or stops: ●During Dry mode, the indoor unit will operate at low speed; in or-
der to adjust room humidity, the indoor unit’s fan may stop from
time to time. Also, the fan may operate at very low speed when
adjusting room humidity.
8
●
During SUPER QUIET operation, the fan will operate at very low speed. 7
●In the monitor of AUTO operation, the fan will operate at very low
speed. 8
WARNING
If the problem persists after performing these checks, or if you notice burning smells, or the OPERATION Indicator Lamp (Fig. 3 5)
and the TIMER Indicator Lamp (Fig. 3 6) ashes, and ECONOMY Indicator Lamp (Fig.3 7) ashes fast. Immediately stop opera-
tion, turn off the electrical breaker and consult authorized service personnel.
Symptom Items to check See page
CHECK ONCE
MORE
Doesn’t operate at all: ●Has the circuit breaker been turn off?
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
—
●Is the timer operating? 9 - 10
Poor Cooling performance: ●Is the Air Filter dirty?
●Are the air conditioner’s intake grille or outlet port blocked?
●Did you adjust the room temperature settings (thermostat) correctly?
●Is there a window or door open?
●In the case of Cooling operation, is a window allowing bright sunlight
to enter? (Close the curtains.)
●In the case of Cooling operation, are there heating apparatus and
computers inside the room, or are there too many people in the room?
—
●Is the unit set for SUPER QUIET operation? 7
The unit operates
differently from the Remote
Controller’s setting:
●Are the Remote Controller’s batteries dead?
●Are the Remote Controller’s batteries loaded properly? 6
9318657012_OM_EN.indd 16 7/31/2012 10:38:39 AM