Fujitsu PRIMERGY TX300 S7 User guide

PRIMERGY TX300 S7
PRIMERGY RX350 S7
System configurator and order-information guide
Contents
Instructions
Configuration diagram 3.5" HDDs
Configuration diagram 2.5" HDDs
Configurator
0 System Software
I Basic unit
II Processor
III Memory
IV Graphics & GPGPU & Co-Processors
V Accessible drives / HDD Extension Box
VI Modular Raid Controller for 3.5" Hard Disks
VII Modular Raid Controller for 2.5" Hard Disks
VIII 3.5" SAS / SATA Hard Disk Drives
IX 2.5" SAS / SATA Hard Disk Drives
X External SAS Disk Array & Backup Drives
XI Fibre Channel
XII Communication/ Network
XIII System Management Products (RemoteView)
XIV Country specific Power Cords
Change report
PRIMERGY Server
February 2014

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/SystemArchitect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III Memory
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options.
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html (internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
(extranet)
Prices and availability see price list and PC-/SystemArchitect.
Subject to change and errors excepted.
Fujitsu PRIMERGY Server 2 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Configuration diagram PRIMERGY
System unit ( 3.5" HDDs )
SIDE VIEW
FRONT VIEW
Hot plug power supplies
3 x 5.25" bays available
3 x HH 5.25" free or 2 x HH 5,25" free + Option A or
1 x HH 5,25" free + Option B or
0 x HH 5.25" free + Option C
Option A Option B Option C
1.6 * 5.25" 2x 1.6 * 5.25" 3x 1.6 * 5.25"
Memories CPUs
Memory CPU1
( Channel A + B + C + D )
Bank I (4 Modules) Xeon 4C, 6C or 8C
Bank II (4 Modules) CPU incl. Heatpipe
Bank III (4 Modules)
Xeon 4C, 6C or 8C
Memory CPU2 CPU incl. Heatpipe
( Channel E + F + G + H)
Accessible drives ( V )
Bank I (4 Modules) Processor ( II )
Bank II (4 Modules) Xeon 4C, 6C or 8C
Mounting Kit DVD(sl) + LSP/LSD: (Option A)
Bank III (4 Modules) CPU with serial QPI - support for SL (0.5") DVD Drive + LSD (Local Service Display)
Interface and - occupies one 5.25" bay
Memory ( III )
4 memory channels
MtK DVD(sl) + LSP/LSD + 2x SAS/SATA LFF HDD: (Option B)
- support for 2x 3.5" SAS/SATA HDD hot plug
+ support for SL (0.5") DVD Drive + LSD (Local Service Display)
MtK DVD(sl) + 4x SAS/SATA LFF HDD: (Option C)
- support for 4x 3.5" SAS/SATA HDD hot plug
+ support for SL (0.5") DVD Drive
PCI Slots
( 3x 120mm Standard Fans; No Redundancy )
Hard disk drives ( VI )
Slot 9 PCIe-3 x4, 252mm @ CPU2 3.5" SAS/SATA
Possibility to install PCIe x8 cards
Option D
4-port SAS backplane
Slot 8 PCIe-3 x16, 252mm @ CPU2
Can be double width slot for GPGPU card! 1 * 3.5" SAS / SATA
Slot 7 PCIe-3 x4, 252mm @ CPU2
Possibility to install PCIe x8 cards 1 * 3.5" SAS / SATA
Slot 6 PCIe-3 x16, 252mm @ CPU2
Can be double width slot for GPGPU card! 1 * 3.5" SAS / SATA
Slot 5 PCIe-2 x4, 252mm @ CPU2
Possibility to install PCIe x8 cards 1 * 3.5" SAS / SATA
Slot 4 PCIe-3 x8, max. 180mm @ CPU1
Possibility to install PCIe x16 cards
4-port SAS backplane
Slot 3 PCIe-3 x8, max. 180mm @ CPU1 1 * 3.5" SAS / SATA
Slot 2 PCIe-3 x8, max. 180mm @ CPU1 1 * 3.5" SAS / SATA
Slot 1 PCIe-3 x8, max. 170mm @ CPU1 1 * 3.5" SAS / SATA
Reserved for modular LAN-Controller
2x internal USB
Slot 10 PCIe-3 x8, max. 170mm @ CPU1 1x USSD 1 * 3.5" SAS / SATA
Internal - reserved for modular RAID-Controller
1x USB Port
Key: Included in basic unit Option ( LP ready = Slots for low profile boards)
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
1. PSU
2. PSU
3. PSU
4. PSU
Air - Channel
Slim DVD
PCIe Slots @ CPU 1
Fan 1
1.6 * 5.25"
LSD Option
not used
2x 92 mm Fans (optional for redundancy)
Fan 3
Fan 5
Fan 4
1.6 * 5.25"
PCIe Slots @ CPU 2
Slim DVD
Air - Channel
Fan 2
Fan 6
4x 92 mm Fans (no redundancy)
Air - Channel
1.6 * 5.25"
LSD Option
Slim DVD
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
SAS / SATA
Fujitsu PRIMERGY Server 3 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Configuration diagram PRIMERGY
System unit ( 2.5" HDDs )
SIDE VIEW
FRONT VIEW
Hot plug power supplies
3 x 5.25" bays available
3 x HH 5.25" free or
2 x HH 5.25" free + Option A or
1 x HH 5.25" free + Option F or
0 x HH 5.25" free + Option A + Option F
#
Option A
Memories CPUs 1.6 * 5.25"
Memory CPU1
( Channel A + B + C )
Bank 1 (4 Modules) Xeon 4C, 6C or 8C Option A Option F
Bank 2 (4 Modules) CPU incl. Heatpipe 1.6 * 5.25" 8x 2.5"
Bank 3 (4 Modules)
Xeon 4C, 6C or 8C
Memory CPU2 CPU incl. Heatpipe
( Channel D + E + F)
Accessible drives ( V )
Bank 1 (4 Modules) Processor ( II )
Bank 2 (4 Modules) Xeon 4C, 6C or 8C Mounting Kit DVD(sl) + LSD: (Option A)
Bank 3 (4 Modules) CPU with serial QPI - support for SL (0.5") DVD Drive + LSD
Interface and - occupies one 5.25" bay
Memory ( III )
4 memory channels
optional SFF SAS/SATA HDD extension Box: (Option F)
- support for 8x 2.5" (SFF) SAS/SATA HDD hot plug
- occupies two 5.25" bays
PCI Slots
( 3x 120mm Standard Fans; No Redundancy )
Slot 9 PCIe-3 x4, 252mm @ CPU2
Possibility to install PCIe x8 cards
2.5" SAS/SATA
Slot 8 PCIe-3 x16, 252mm @ CPU2
Can be double width slot for GPGPU card!
Option E
Slot 7 PCIe-3 x4, 252mm @ CPU2
Possibility to install PCIe x8 cards
Slot 6 PCIe-3 x16, 252mm @ CPU2
Can be double width slot for GPGPU card!
Slot 5 PCIe-2 x4, 252mm @ CPU2
Possibility to install PCIe x8 cards
Slot 4 PCIe-3 x8, max. 180mm @ CPU1
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 180mm @ CPU1
Slot 2 PCIe-3 x8, max. 180mm @ CPU1
Slot 1 PCIe-3 x8, max. 170mm @ CPU1
Reserved for modular LAN-Controller
Slot 10 PCIe-3 x8, max. 170mm @ CPU1
Internal - reserved for modular RAID-Controller
internal USB
or USSD
Key: Included in basic unit Option ( LP ready = Slots for low profile boards)
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
Fan 1
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
Fan 4
1x 8-port SAS backplane
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
not used
Hard disk drives ( VI )
Air - Channel
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
Air - Channel
1 * 2.5" SAS / SATA
2.5" SAS/SATA
2.5" SAS/SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1 * 2.5" SAS / SATA
1. PSU
2. PSU
3. PSU
4. PSU
Fan 2
LSD Option
Fan 3
2x 92 mm Fans (optional for redundancy)
Fan 6
Slim DVD
PCIe Slots @ CPU 2
1.6 * 5.25"
1.6 * 5.25"
4x 92 mm Fans (no redundancy)
PCIe Slots @ CPU 1
Fan 5
Slim DVD
Optional 8-port SAS backplane
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
2.5" SAS/SATA
LSD Option
not used
2.5" SAS/SATA
2.5" SAS/SATA
Fujitsu PRIMERGY Server 4 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
SW Configurator 32 bit
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
VMware-Software is not allowed to be ordered
- VirtualCenter Management Server for any server released for Windows Server 2003 separately.
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems Exception: VMware SW
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Linux - Software **)
- Open Enterprise Server ***)
- SuSE Linux ES (OEM): LO
- Windows Server 2008 Enterprise - Red Hat EL (OEM): LO
- Windows Server 2008 Standard
PRIMECLUSTER *)
- Clustering
- Load Balancing
Microsoft - Windows Server 2008 Client Access Licenses SCO - Software: **)
-
Windows Server 2008 Device CAL
- SCO OpenServer
-
Windows Server 2008 User CAL
(only 1- and 2-way Tower servers)
- Windows Server 2008 Remote Desktop Services Device CAL
- SCO UnixWare (only 1-, 2, and
- Windows Server 2008 Remote Desktop Services User CAL
4-way Tower and Rack servers)
x10sure *)
x10sure Control Nodes and Compute Nodes
Windows Server 2003 Compute Nodes
for PRIMERGY BX600, RX/TX
MultiPath, Duplex Data Manager (DDM)
W2K; W2K3 Linux (W-DDM)
for PRIMERGY except all mono PY systems Details eg. version numbers are published
on the page referred to
Manageability Software: V**) *) Pay attention to the x10sure release and ordering information in the Extranet under
- iRMC advanced Pack https://ts.fujitsu.com/x10sure
- RemoteView Software
- RemoteView Service Board
- RemoteView Diagnosis *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
- RemoteDeploy https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
- Altiris Server Deployment
**) Pay attention to release and order information in PRINCE -> Operating System
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Backup-Software /
Application-Software: U
- ARCserve
***) Supply over distribution or procurement from FSC VP BC Software
- openSM2
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users:
http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Microsoft - Downgrade Media Only
Start PRIMERGY
Fujitsu PRIMERGY Server 5 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
SW Configurator 64 bit (EM64T / IA64)
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding
is not allowed to be ordered
software configurator accessible via the Extranet under separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
VMware-Software
- VirtualCenter Management Server for any server released for Windows Server 2003
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
Citrix XenServer / Essentials for XenServer
- XenCenter Management Server for any server released for Windows 2000/XP/Vista and Server 2003/2008
- XenServer and Essentials for XenServer released for RX200S5, RX300S4/S5, RX600S4, BX620S4/S5, BX920S1
Microsoft Hyper-V Server and System Center for SME
- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2
- Microsoft System Center Essentials 2010 for any server released for Windows Server 2008 R2
- Microsoft Hyper-V Server 2008 R2 - Free Microsoft Web Download (not necessary for Windows Server 2008 R2 customers)
as soon as available
Microsoft - Windows Server 2008 R2 Server Licenses Microsoft - Windows Small Business Server 2011
- Windows HPC Server 2008 R2 Suite - Windows Small Business Server Standard 2011
- Windows Server 2008 R2 Datacenter - Windows Small Business Server 2011 Premium Add-on
- Windows Server 2008 R2 Enterprise
-
Windows Server 2008 R2 Standard
-
Windows Web Server 2008 R2
as soon as available
- Windows Small Business Server 2011 Standard I Premium Device CAL
-
Windows Small Business Server 2011 Standard I Premium User CAL
-
Windows Server 2008 Enterprise
- Windows Server 2008 Remote Desktop Services Device CAL
- Windows Server 2008 Standard - Windows Server 2008 Remote Desktop Services User CAL
Microsoft - Windows Server 2008 Client Access Licenses
- Windows Server 2008 Device CAL
- Windows Server 2008 User CAL
- Windows Server 2008 Remote Desktop Services Device CAL Linux - Software *) **)
- Windows Server 2008 Remote Desktop Services User CAL # Open Enterprise Server ***)
only
- SuSE Linux ES (OEM): LO
EM64T - Red Hat EL (OEM): LO
PRIMECLUSTER *)
- Clustering
- Load Balancing
QuickTransit (QT)
only Transition Solaris Apps.
EM64T to x86-64 PY with Linux
only MultiPath, Duplex Data Details eg. version numbers are published
EM64T Manager (DDM) on the page referred to
Windows, Linux (W-DDM)
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
Manageability Software: V**)
- iRMC advanced Pack **) Pay attention to release and order information in PRINCE -> Operating System
only - RemoteView Software https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
EM64T - RemoteView Service Board
- RemoteView Diagnosis ***) Supply over distribution or procurement from FSC VP BC Software
- RemoteDeploy
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
Continue with PRIMERGY
for partners:
https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
HW configurator
Microsoft Windows Small Business Server 2011 Client Access
Microsoft - Downgrade Media Only
Start PRIMERGY TX300 S7
Fujitsu PRIMERGY Server 6 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Start PRIMERGY TX300 S7
Section IBasic units
SAS - System unit, Rack and Floorstand including:
* By a key lockable front bezel in floorstand version
* Basic units with:
- 4 Hot-Plug Power Supply Slots
- 4 Standard Fans (92mm; no redundancy)
- 12 memory DIMMs per CPU ( max 384GB ) => Total 24 DIMMs ( max 768GB ) for two CPU`s
- SAS/ SATA backplane with hot plug bays for 4x 3.5" HDD`s or 8x 2.5" HDD's & SSD's
* 3 drive bays 5,25" for accessible drives free available.
* Integrated ServerView Diagnostics Technology with an modul for indication of failed
components via LED`s.
Simultaneously components are marked which can be replaced by the customer.
This LEDs can be dispalyed during service even without mains connection.
Options:
* Up to 4 hot plug power supply modules with 450W & 800W
* 4x 3.5" or 8x 2.5" HD backplane kits
* - Optional modular RAID 0/1 controllers with IME (Integrated Mirroring Enhanced) support
based on LSI 1064 or LSI SAS2008 chipset or as alternative
- optional modular RAID 5 controller based on LSI SAS2108 chipset
* One 0,5" bay can be configured with an optional LC- display for LocalView in a drawer
Systemboard D2649 with:
* Up to two Xeon 4C, 6C & 8C CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series (codenamed Patsburg)
* 10 PCI slots:
@ first CPU - 4x PCIe-3 x8 (one notched to install x16 cards)
@ first CPU - 1x PCIe-3 x8 (for internal modular RAID controller only)
@ second CPU - 2x PCIe-3 x16
@ second CPU - 2x PCIe-3 x4
@ second CPU - 1x PCIe-2 x4
* 24 memory slots for max. 768GB RAM DDR3 available
- Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel )
Possible max. configurations are:
24x 32GB LRDIMM (quad rank modules) = 768GB
24x 16GB RDIMM (dual rank modules) = 384GB
16x 8GB UDIMM (dual rank modules) = 128GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise
- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2
- Rank sparing mode is supported with min. 2x 1R/2R or 1x 4R modules for RDIMM or LRDIMM
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* iRMC S3 (integrated Remote Management Controller) on-board server management controller with
dedicated 10/100/1000 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port 1
* Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller):
Supported graphical resolutions are:
1920x1200x16bpp, 1920x1080x16bpp, 1600x1200x16bpp, 1680x1050x16bpp, 1440x900x16bpp,
1280x1024x32bpp, 1152x864x16bpp, 1024x768x32bpp, 800x600x32bpp, 640x480x32bpp
A
Fujitsu PRIMERGY Server 7 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
A
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)
* 1x RS-232-C (serial, 9 pins)
* 1x VGA (15 pins)
* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces on the front:
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 1x VGA (15 pins) as an option
* 1x Service-LAN RJ45 as an option
Interfaces internal:
* 2x released internal USB Interfaces for backup devices,
* 1x USB 2.0 ( UHCI ) with 480MBit/s for dongle funcionality, no USB wakeup
* 1x USSD
Cables:
* SATA cable for DVD.
* 2x SAS cables for connection of 4 SAS-ports each incl. signaling
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
B
Fujitsu PRIMERGY Server 8 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
B
TX300 S7 Floorstand System RX350 S7 Rack System
without CPU, Memory and PSU without CPU, Memory and PSU
with:
with:
- Four hot plug fans (no redundancy)
- Four hot plug fans (no redundancy)
- One CPU ( first CPU ) has to be configured - One CPU ( first CPU ) has to be configured
additionally for a base configuration additionally for a base configuration
- One memory kit per CPU has to be - One memory kit per CPU has to be
configured for a base configuration configured for a base configuration
- One power supply has to be - One power supply has to be
configured for a base configuration configured for a base configuration
- No Rackmount Kit included !
- The Rackmount Kit or the option
no Rackmount Kit has to be ordered
separately
LFF Base Unit S26361-K1390-V101 LFF Base Unit S26361-K1390-V301
- 4-port SAS backplane for 4x 3.5" hot plug SAS - 4-port SAS backplane for 4x 3.5" hot plug SAS
or SATA HD`s incl. cables for connection to the
or SATA HD`s incl. cables for connection to the
modular 8-port SAS controllers
modular 8-port SAS controllers
SFF Base Unit S26361-K1390-V201 SFF Base Unit S26361-K1390-V401
- 8-port SAS backplane for 8x 2.5" hot plug SAS - 8-port SAS backplane for 8x 2.5" hot plug SAS
or SATA HD`s incl. cables for connection to the
or SATA HD`s incl. cables for connection to the
modular 8-port SAS controllers
modular 8-port SAS controllers
D C
Fujitsu PRIMERGY Server 9 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
C
PRIMECENTER Rack
S26361-F2735-E285
S26361-F2735-E111
S26361-F2735-L285
RMK-F2_DI_CMA_QRL_LV No Rackmount-Kit option RMK-F2_DI_CMA_QRL_LV
telescopic drop-in rail, full extr. Only for loose deliveries
for loose delivery
1-hand-mounting No mounting in racks possible S26361-F2735-L31
RMK - 1 pair consisting of max. 1x per system Adapter angle PC/DC-Rack, till 200Kg
- vario carrier length variable
necessary for mounting RMKs in
with quick release lever support asymmetrical racks
- telescopic drop-in rails S26361-F2735-L7
with CMA adapter Lateral cable management
1x per system Dcan only be mounted
in asymmetrical PRIMECENTER
S2 or new M1 racks in 1U above RMK
S26361-F4530-E12 S26361-F4530-E10
Mounting systems higher 2U in Mounting in
asymmetrical racks symmetrical racks
with 2U support bracket
(no support bracket needed)
S26361-F2735-E71 S26361-F2735-E82 Cable Management Arm (CMA) can
Lateral cable management 2U cable management arm (CMA) only be used for FTS RMKs with
for 2U servers or higher for 2U server or higher CMA adapter
- for asymmetrical racks - for symmetrical racks
PRIMECENTER S2 or M1 M1 or 3rd party racks S26361-F2735-L82
- 1 bracket PC Rack asym. Fujitsu racks Cable management arm for 2U Server
1x per system 1x per system or higher for loose delivery
can only be mounted at RMK with
CMA adapter
for loose delivery
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered "Rack-mounting ex factory"
completely pre-mounted and This service is to be ordered once
all wired connections are tested. per installable server/storage
With PCR S2 12U, 24U, 38U and subsystem, in order to get the
PRC M1 16U, 24U, 42U: server/storage subsystem
Systems and components mounted into the racks.
will be delivered installed in the rack In case of the 46 U PCR S2
With PCR S2 racks 46U:
this service has to be ordered,
Systems and components to get the mounting kits and the
will be delivered separately cables installed.
To be ordered only together with
a PRIMECENTER rack
PCR S2 e.g. S26361-K826-V10x
new PCR M1 e.g. S26361-K827-Vxxx
refer PCR S2 or M1 rack configurator
max. 1x per System PRIMERGY Classic 19" rack is not supported
For later conversion the following kits are available:
1.) Conversion kit 2 Floor -> Rack S26361-F1729-L260
Conversion PRIMERGY TX300 S7 base unit floorstand into
base unit rack. Only conversion, no mounting kit.
Mounting kit has to be ordered seperatly.
D
Fujitsu PRIMERGY Server 10 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
D
For min. configuration one power supply has to be selected
For basic redundancy at least 2 PSUs of the same type have to be configured
There is only one PSU type (450W or 800W) allowed
S26113-F575-E10 S26113-F574-E10 S26113-F574-E99 * *For order completeness only
Power supply 450W Power supply 800W Power Supply Dummy Will be added automaticly with
4x
(hot plug)
(hot plug)
System Architect Version ≥ V9.3
occupies one bay for occupies one bay for occupies one bay for
hot plug power supply hot plug power supply hot plug power supply
max. 4x per system max. 4x per system max. 3x per system
For later upgrades the following kits are available:
1 power supply module 450W hot plug: S26113-F575-L10
Supplementary module
1 power supply module 800W hot plug: S26113-F574-L10
Supplementary module
Attention: There is no power cable included!
If CPU's with a TDP >= 130W are used (e.g. E5-E2643, E5-2667, E5-2680, E5-2690), the hot plug
redundant fan kit (S26361-F3667-E1) is required.
S26361-F3667-E1 for later upgrade with redundant fan upgrade kit
Hot Plug Redundant Fan Hot Plug Redundant Fan Upgrade Kit: S26361-F3667-L1
Upgrade Kit For upgrade of standard into redundant fans
max. 1x per system Constist of two fan boxes with 92mm fan each
S26361-F3552-E1 S26361-F3552-L1
TPM Module
TPM Module add-on kit
Trusted Platform Module on Motherboard for later integration (loose delivery)
Use according to import restrictions Trusted Platform Module on Motherboard
max. 1x per system max. 1x per system
Be aware of import restrictions!
Only 1 TPM per system.
Loose delivery for later
integration possible for customer.
E
Fujitsu PRIMERGY Server 11 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
E
Section II Processor
There are 2 processor sockets available.
The first socket is always equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Two processors with different type are not possible
If CPU's with a TDP >= 130W are used (e.g. E5-E2643, E5-2667, E5-2680, E5-2690), the hot plug
redundant fan kit (S26361-F3667-E1) is required.
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
Note: Max. DDR3 Bus Speed depends on:
One of following CPU´s has to be selected as first CPU
- max. DDR3 Bus Speed from the CPU and
for an orderable basic unit - max. DDR3 Memory Speed and
Optional second CPU has to be the same type like the first CPU - max. memory modules on one memory channel
Basic 4C CPU's
- 1x 64-bit Intel Xeon (10MB Smart Cache)
1066 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2603 4C/4T 1.80GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E180
Xeon E5-2609 4C/4T 2.40GHz 10MB 6.40GT/s 1066MHz 80W S26361-F3685-E240
Standard Turbo 6C CPU's
- 1x 64-bit Intel Xeon (15MB Smart Cache); Hyper-Threading (HT);
1333 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2620 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E200
Xeon E5-2630 6C/12T 2.30GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E230
Xeon E5-2640 6C/12T 2.50GHz 15MB 7.20GT/s 1333MHz 95W S26361-F3676-E250
Advanced Turbo+ 8C CPU`s
- 1x 64-bit Intel Xeon (20MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2650 8C/16T 2.00GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E200
Xeon E5-2660 8C/16T 2.20GHz 20MB 8.00GT/s 1600MHz 95W S26361-F3686-E220
Xeon E5-2665 8C/16T 2.40GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E240
On special release only
Xeon E5-2670 8C/16T 2.60GHz 20MB 8.00GT/s 1600MHz 115W S26361-F3686-E260
Xeon E5-2680 8C/16T 2.70GHz 20MB 8.00GT/s 1600MHz 130W S26361-F3686-E270
Xeon E5-2690 8C/16T 2.90GHz 20MB 8.00GT/s 1600MHz 135W S26361-F3686-E290
Frequency Optimized Turbo 2C, 4C & 6C CPU`s
- 1x 64-bit Intel Xeon (5/10/15MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 6,40/7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2637 2C/4T 3.00GHz 5MB 6.40GT/s 1600MHz 80W S26361-F3687-E300
Xeon E5-2643 4C/8T 3.3GHz 10MB 6.40GT/s 1600MHz 130W S26361-F3687-E330
Xeon E5-2667 6C/12T 2.90GHz 15MB 7.20GT/s 1600MHz 130W S26361-F3687-E290
Low Power 4C/6C/8C CPU's
- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT);
1333/1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2630L 6C/12T 2.00GHz 15MB 7.20GT/s 1333MHz 60W S26361-F3688-E200
Xeon E5-2650L 8C/16T 1.80GHz 20MB 8.00GT/s 1600MHz 70W S26361-F3688-E180
F
Fujitsu PRIMERGY Server 12 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
F
Section
III Memory
- There are 12 memory slots per CPU for max.
384GB LRDIMM (12x 32GB 4R)
192GB RDIMM (12x 16GB 2R)
32GB UDIMM (8x 4GB)
=> max. 768GB for two CPU`s ( 384GB per CPU ), using LRDIMM
- The memory area is divided into 4 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a 2 DIMMs per channel configuration, following frequencies are supported:
- 1.5V - 1600MHz max (depending on CPU, special memory modules)
- 1.35V - 1333MHz max (depending on CPU)
In a 3 DIMMs per channel configuration, memory will operate at 1.5V only.
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated inany order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by unbuffered memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules
In each memory bank channel Aand B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B / D is always the mirrored memoryof channel A / B of CPU 1
In channel F / H is always the mirrored memory of channel E / G of CPU 2
Minimum configuration is: 4x identical modules
This mode is not supported by unbuffered memory modules
F1
Fujitsu PRIMERGY Server 13 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
F1
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3694-E1 Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shownin System Memory.
For effective capacity within a channel, please have a look below.
Supported for RDIMM / LRDIMM only.
1x per CPU Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3694-E2 Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.
Multiple of 4 identical modules to be configured per CPU
S26361-F3694-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM / LRDIMM only.
Multiple of 4 identical modules to be configured per CPU
1R
2R
1R
2R
4R
4R
na na na na na
na na
na na
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
Max. DDR3 memory speed depends on the memory configuration
- one DDR3 unbuffered ECC mem. Module, 1.35V
(No of mem modules per channe) as well as on the CPU type.
Choose up to 8 order codes per CPU The memory channel with the lowest speed defines the speed
2GB (1x2GB) 1Rx8 L DDR3-1600 U ECC S26361-F3694-E513 of all CPU channels in the system, also for the channels of the
4GB (1x4GB) 2Rx8 L DDR3-1600 U ECC S26361-F3694-E514 second CPU if configured.
Registered Memory (RDIMM) no SDDC (chipkill) support For real memory speed (depending on memory type / population),
- one DDR3 registered ECC mem. Module, 1.35V please check the spreadsheet "Memory speed" below
No mix with any other types of memory modules possible
Choose up to 12x for 1R/2R or 8x for 4R per CPU
For performance reasons, we do not recommend
to configure more than 8 DIMMs per CPU
4GB (1x4GB) 2Rx8 L DDR3-1600 R ECC S26361-F3695-E514
Registered Memory (RDIMM) with SDDC (chipkill) support
8/12x per - one DDR3 registered ECC mem. Module, 1.35V Mix of memory modules is only possible within the same group
CPU, max. 1333MHz supported with up to 2DPC (8 modules/CPU)
2/3 modules Choose up to 12 order codes per CPU
per channel 4GB (1x4GB) 1Rx4 L DDR3-1333 R ECC S26361-F3696-E514 new due to supply
8GB (1x8GB) 2Rx4 L DDR3-1333 R ECC S26361-F3696-E515 new due to supply
Registered Memory (RDIMM) with SDDC (chipkill) support
- one DDR3 registered ECC mem. Module, 1.35V
1600MHz supported with up to 2DPC (8 modules/CPU)
at 1.5V
Choose up to 12 order codes per CPU
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3697-E514
8GB (1x8GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E515
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3697-E516
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 12 order codes per CPU
16GB (1x16GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E516 as soon as available
32GB (1x32GB) 4Rx4 L DDR3-1333 LR ECC S26361-F3698-E517
as soon as available
G
40GB
80GB
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
UDIMM
RDIMM
LRDIMM
2GB
2GB
4GB
8GB
2R
16GB
16GB
32GB
1DPC
12GB
24GB
2DPC
4GB
12GB
24GB
28GB
56GB
3DPC
8GB
20GB
40GB
Fujitsu PRIMERGY Server 14 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Memory Configuration PRIMERGY TX300 S7 / RX350 S7
Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels.
If you need more than 12 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM
UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode Configuration Application
SDDC (chipkill) support any no no yes detect multi-bit errors
Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity
Mode
use UDIMM modules for lowest cost
Mirrored Channel Mode *) 4 identical Modules / Bank no no yes offers maximum security
Performance Mode 4 identical Modules / Bank yes yes yes offers maximum performance and capacity
Rank Sparing Mode *) min. 2 Ranks / Channel no no yes
balances security and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity Configuration UDIMM RDIMM LRDIMM Notes
Min. Memory per CPU
1 Module / CPU
1x2GB 1x4GB 1x 16GB
with one CPU
Max. Memory per CPU 8/12 Modules / CPU 8x4GB 12x16GB
12x 32GB
with one CPU
Max. Memory per System 16/24 Modules / System 64GB 384GB 768GB if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Voltage setting (BIOS)
DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC DPC
CPU with 1333MHz DDR3 Bus
CPU with 1066MHz DDR3 Bus
1R - Single Rank
2R - Dual Rank
4R - Quad Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
3DPC = 3 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I black sockets
Bank II blue sockets
Bank III
green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2 up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU
Bank II on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
Bank III on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
(can not be populated by UDIMM or 4R RDIMM memory modules)
- See below and next page for a detailed descriptions of the memory configuration supported.
1.5V [default]
1.35V
1.5V [default]
1.35V
1.5V [default]
1.35V
Mem. Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC)
and voltage setting (BIOS)
UDIMM 1600MHz
RDIMM 1600MHz
LRDIMM 1333MHz
UDIMM
RDIMM
RDIMM
LRDIMM
x8
x8
x4
1
2
3
1
2
3
3
1
2
3
1
2
3
1
2
3
1
2
CPU with 1600MHz DDR3 Bus
1333
1333
-
1066
1066
1600
-
1333
1333
1333
-
1066
1066
-
1066
1333
1066
1333
1333
-
-
1600
1600
1066
1333
1333
1066
-
1066
1066
1066
1066
1066
-
-
-
1066
-
-
1066
1066
1066
-
1333
1333
1066
1333
1333
-
1333
1066
1066
1066
1066
1066
1066
-
1066
1066
-
on special release
as soon as available
Fujitsu PRIMERGY Server 15 of 36

System configurator and order-information guide
1. Independent Channel Mode PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Bank I Data Mirror Data Mirror Data Mirror Data Mirror optional, same type in Bank per CPU
(black sockets)
Bank II Data Mirror Data Mirror Data Mirror Data Mirror -------- not used
(blue sockets)
Bank III
Data Mirror Data Mirror Data Mirror Data Mirror
(green sockets)
Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 4 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 4 identical modules has to be ordered.
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8 Core)
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Fujitsu PRIMERGY Server 16 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
4. Rank Sparing Mode
required
required if 2nd CPU is configured
Bank I Spare Spare Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data
-------- not used
(green sockets)
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data Data Data
required if 2nd CPU is configured
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, same type in Channel per CPU
Bank III
R1 Data Data Data Data Data Data Data Data optional, any type
(green) R2 Data Data Data Data Data Data Data Data
-------- not used
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare
required
(black) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data required if 2nd CPU is configured
R4 Data Data Data Data Data Data Data Data
optional, same type in Channel per CPU
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, any type
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data -------- not used
Bank III
R1 Data Data Data Data Data Data Data Data
(green) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
2-Rank Memory modules (RDIMM)
1-Rank Memory modules (RDIMM)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
Channel G
Channel H
1st XEON CPU
(4/6/8 Core)
2nd XEON CPU
(4/6/8) Core)
4-Rank Memory modules (LRDIMM)
Channel F
Channel A
Channel B
Channel C
Channel D
Channel E
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Fujitsu PRIMERGY Server 17 of 36

System configurator and order-information guide
H
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Section
IV
Graphics & GPGPU & Co-Processors
Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller) with following resolutions:
1920x1200x16bpp, 1920x1080x16bpp, 1600x1200x16bpp, 1680x1050x16bpp, 1440x900x16bpp,
1280x1024x32bpp, 1152x864x16bpp, 1024x768x32bpp, 800x600x32bpp, 640x480x32bpp
S26361-F2571-E26 S26361-F2748-E537
Optional Front-VGA PY VGA card 512MB PCI-e x1 S26361-F2748-L537
for Onboard Controller only NVIDIA NVS300 PY VGA card 512MB PCI-e x1
consists of internal cable and 512 MB PCIe-x1
for loose delivery
front VGA connector Connectors: 1x LFH 59
max. 1x per system
cable kit for 2x DVI or 2x VGA
cable kits included
Dual head + professional 2-D + 3-D
supported for Windows OS
native driver support for Linux OS
full height bracket
max. 1x per system
The hight end optional NVIDIA NVS300 graphic card offers dual head operation
and fully 3D video support. The cables for either two times
DVI-I or VGA (cable kit) connections are part of the delievery.
Remote Video direction via iRMC must be disabled.
This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
Only one card per server is allowed.
One or two GPGPU (General Purpose Graphical Processor Unit) can be ordered as option.
The Power Cable kit has to be ordered seperatly and will be installed if ordered ex factory together
with the GPGPU card. New cards requires the suitable Air Duct and bracket kit!
No mix betwenn differnet types of GPGPU or Co-Processor cards allowed
S26361-F3736-E1
PY GPGPU Cable Kit
consists of 2 power cables and S26361-F3736-L1
an universal PCI card holder
PY GPGPU Cable Kit
max. 1x per system
consists of 2 power cables and
an universal PCI card holder
as long as stock last vor loose delivery
S26361-F2856-E997
PY NVIDIA Tesla C2075 Computing-Processor PY NVIDIA Tesla C2075 Computing-Processor
NVIDIA Tesla C2075
800W PSU is recommended
6 GB Memory
PCIe Gen2-x16 S26361-F2856-L997
2x for GPGPU purpose only PY GPU card 6GB PCIe2 x16
800W PSU is recommended
for loose delivery
occupied space for two PCI slots
full height bracket
max. 2x per system
This mounting kits contain an airduct that uses 2 bays 1.6” x 5.25”. S26361-F3736-L2
If these are ordered this 2 bays cannot contain ODD or backup devices. PY K20 / K20X Mounting Kit
consists of 2 power cables, an
S26361-F3736-E2 Note the mountingkit is needed PCI card holder + Airduct
PY K20 / K20X Mounting Kit
only one timer per System
for loose delivery
consists of 2 power cables, an
The GPGPU cards can be ordered twice
1x PCI card holder + Airduct PY NVIDIA Tesla K20 / K20X
max. 1x per system
Computing-Processor 800W PSU is recommended
With 2x PY NVIDIA Tesla K20X
ambient temperature should not excced 30°C
S26361-F2222-E22 S26361-F2222-E24
PY NVIDIA Tesla K20 Computing-Processor PY NVIDIA Tesla K20X Computing-Processor
NVIDIA Tesla K20 NVIDIA Tesla K20X
5 GB Memory
6 GB Memory
PCIe Gen2-x16
PCIe Gen3-x16 technical via card BIOS GEN2
2x 2496 cores 2688 cores
for GPGPU purpose only for GPGPU purpose only
power cables from PSU needs to be ordered power cables from PSU needs to be ordered
800W PSU is recommended
800W PSU is recommended
occupied space for two PCI slots
occupied space for two PCI slots
full height bracket full height bracket
max. 2x per system
max. 2x per system
S26361-F2222-L22
S26361-F2222-L24
Ifor loose delivery
NVIDIA Tesla GPGPU
Fujitsu PRIMERGY Server 18 of 36

System configurator and order-information guide
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
I
One or two GPGPU (General Purpose Graphical Processor Unit) can be ordered as option.
The Power Cable kit has to be ordered seperatly and will be installed if ordered ex factory together
with the GPGPU card. New cards requires the suitable Air Duct and bracket kit!
No mix betwenn differnet types of GPGPU or Co-Processor cards allowed
This mounting kits contain an airduct that uses 2 bays 1.6” x 5.25”. S26361-F3736-L5
If these are ordered this 2 bays cannot contain ODD or backup devices. Intel Xeon Phi Mounting Kit
consists of 2 power cables, an
S26361-F3736-E5 Note the mountingkit is needed PCI card holder + Airduct
Intel Xeon Phi Mounting Kit
only one timer per System
for loose delivery
1x consists of 2 power cables, an
The GPGPU cards can be ordered twice
PCI card holder + Airduct
max. 1x per system
PY Intel Xeon Phi Co-Processors
800W PSU is recommended
S26361-F4100-E511
PY Intel Xeon Phi Co-Processor 5110P
Intel Xeon Phi Co-Processor 5110P
8 GB GDDR5 Memory S26361-F4100-L511
PCIe Gen2-x16
2x 60 cores and 240 threads
for loose delivery
for Co-processing purpose only
power cables from PSU needs to be ordered
800W PSU is recommended
occupied space for two PCI slots
full height bracket
max. 2x per system
J
Intel Xeon Phi Co-processor
Fujitsu PRIMERGY Server 19 of 36

System configurator and order-information guide
J
PRIMERGY TX300 S7 / RX350 S7 Status 2014-01-30
Section
VAccessible drives and 3.5" SAS / SATA HDD extension box
There are 3 bays (1.6" x 5.25") for accessible drives.
see Conf. Diagram Option A
see Conf. Diagram Option B
see Conf. Diagram Option C
occupies 1 accessible bay occupies 2 accessible bays occupies all 3 bays
for all base units only 3.5" HDD base units only 3.5" HDD base units
S26361-F2826-E205 S26361-F2826-E105 S26361-F2826-E435
Mounting Kit DVD(sl) + LSD
Mounting Kit DVD(sl) +
Mounting Kit DVD(sl) +
Occupies one 5.25" x 1.6" bay
LSP/LSD + SAS LFF HDD SAS LFF HDD
in the accessible bay area
Occ. two 5.25" x 1.6" bays
Occupies all 5.25" x 1.6" bays
Offers bays for: in the accessible bay area in the accessible bay area
- 1x LSD option Offers bays for:
Offers bays for:
- 1x 0.5 * 5.25" SATA DVD - 1x LSD/LSP option - 1x 0.5 * 5.25" SATA DVD
max. 1x per system
- 1x 0.5 * 5.25" SATA DVD - 4x 3.5" SAS/SATA HDD's
- 2x 3.5" SAS/SATA HDD`s Two 1 * 3,25" satin black bezels
One 0.5 * 3.5" satin black bezel
for SAS HDD bays
for LSD/LSP bay max. 1x per system
One 0.5 * 5.25" satin black bezel
for 0.5 * 5.25" DVD bay
Two 1 * 3,25" satin black bezels
for SAS HDD bays
max. 1 per system
S26361-F3668-E1 S26361-F3668-E1
24x SAS Expander 24x SAS Expander
required for HDDs within
required for HDDs within
accessible drives area
accessible drives area
Raid Controller required Raid Controller required
max. 1x per system max. 1x per system
S26361-F2557-E105 S26361-F2557-E106
Local Service Display incl. Adapter Local Service Display incl. Install. kit
Customer Self Service Customer Self Service
LSD module incl. adapter LSD module incl. mounting kit
0.5" x 5.25" 0.5" x 5.25"
max. 1x per System max. 1x per system
S26361-F3269-E2 S26361-F3641-E2
DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA
all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD
only W2K, W3K and Linux BD DL and all CD/DVD formats
0.5 x 5.25", black bezel 0.5 x 5.25"
max. 1x per system max. 1x per system
S26361-F3266-E2 S26361-F3267-E2
DVD-ROM HH SATA
DVD-RW supermulti HH SATA
16x DVD 48x CD all formats, DUAL/DL, DVD-RAM
only W2K, W3K and Linux
1.6 x 5.25", black bezel 1.6 x 5.25", black bezel
max. 1x per system max. 1x per system
K
Fujitsu PRIMERGY Server 20 of 36