Fujitsu PRIMERGY TX1310 M5 User manual

FUJITSU Server PRIMERGY TX1310 M5
Upgrade and Maintenance Manual
Upgrade and Maintenance Manual - English
03/2022

Comments… Suggestions… Corrections…
The User Documentation Department would like to know your opinion of this manual. Your
feedback helps us optimize our documentation to suit your individual needs.
Feel free to send us your comments by e-mail to [email protected].
Documentation creation according to ISO 9001 and ISO 27001
To ensure high quality and information security standards while creating documentation, the
quality management system and information security management system of cognitas are
certified in compliance with ISO 9001 and ISO 27001.
cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de/en/
Copyright and Trademarks
Copyright 2022 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
–The contents of this manual may be revised without prior notice.
–Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
–No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure that
these safety notes are understood before using the product. Keep this manual
and the "Safety Notes and Regulations" manual in a safe place for easy
reference while using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures.
VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the printed circuit board
assemblies of the product and in the mouse and keyboard are limited-life
components. Use of these components beyond their operating life may result
in electrolyte leakage or depletion, potentially causing emission of foul odor or
smoke.
As a guideline, in a normal office environment (25 °C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
TX1310 M5 Upgrade and Maintenance Manual

The product is not suitable for use at visual display workplaces according to §2
of the Workplace Regulations (applies to all server systems except TX server
systems).
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, the use of an
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Upgrade and Maintenance Manual TX1310 M5

Only for Japan: About SATA HDDs
The SATA version of this server supports HDDs with SATA/BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
For more information on the usage and operation conditions of each available
type of HDD, see the following internet address:
https://jp.fujitsu.com/platform/server/primergy/harddisk/
Only for Japan:
Shielded LAN cables should be used in this product.
UK Importer information
Fujitsu Services Limited
22 Baker Street, London, W1U 3BW, United Kingdom
TX1310 M5 Upgrade and Maintenance Manual

Version history
Issue
number
Issue date Description
V 1.0 11/2021 Initial release
03/2022 cable plan updated
Upgrade and Maintenance Manual TX1310 M5

Content
1 Introduction 15
1.1 Concept and target groups of this manual 15
1.2 Notational conventions 15
2 Before you start 17
2.1 Basic information 17
2.1.1 Proceeding 17
2.1.2 Advanced Thermal Design (ATD) 17
2.1.3 Installing optional components 18
2.2 Classification of procedures 18
2.2.1 Assignment of unit categories 18
2.2.2 Customer Replaceable Units (CRU) 19
2.2.3 Upgrade and Repair Units (URU) 19
2.2.4 Field Replaceable Units (FRU) 20
2.3 Average task duration 21
2.4 Tools you need at hand 22
2.5 Documentation overview 22
2.5.1 About availability of manuals 22
2.5.2 List of documents 23
3 Important information 25
3.1 Introduction 25
3.2 Safety instructions 25
3.2.1 Basic safety instructions 25
3.2.2 Before starting up 26
3.2.3 Installation and operation 26
TX1310 M5 Upgrade and Maintenance Manual

3.2.4 Batteries 29
3.2.5 Working with optical disk drives (ODDs) and media 29
3.2.6 Laser information 31
3.2.7 Modules with Electrostatic-Sensitive Devices (ESD modules) 31
3.2.8 Transporting the server 33
3.2.9 Installing the server in the rack 34
3.2.10 Other important information 34
3.3 CE conformity 35
3.4 FCC Class A Compliance Statement 35
3.5 Environmental protection 36
4 Basic hardware procedures 39
4.1 Using diagnostic information 39
4.1.1 Proceeding 39
4.2 Unlocking the server 39
4.3 Removing the bay cover 40
4.4 Shutting down the server 41
4.5 Disconnecting the power cord 42
4.6 Getting access to the component 43
4.6.1 Safety notes 43
4.6.2 Removing the side cover 44
4.6.3 Removing the front cover 44
4.6.4 Removing the top HDD cage 46
4.6.5 Removing the system board tray 48
4.7 Reassembling 50
4.7.1 Safety notes 50
4.7.2 Inserting in the system board tray 50
4.7.3 Installing the top HDD cage 52
4.7.4 Installing the front cover 54
4.7.5 Installing the side cover 56
Content
Upgrade and Maintenance Manual TX1310 M5

4.8 Connecting the power cord 56
4.9 Switching on the server 57
4.10 Installing the bay cover 58
4.11 Locking the server 59
5 Basic software procedures 61
5.1 Starting the maintenance task 61
5.1.1 Suspending BitLocker functionality 61
5.1.2 Removing backup and optical disk media 63
5.1.3 Verifying and configuring the backup software solution 63
5.2 Completing the maintenance task 63
5.2.1 Updating or recovering the BIOS 63
5.2.2 Reconfiguring the backup software solution 64
5.2.3 Enabling replaced components in the BIOS 65
5.2.4 Verifying the system time settings 65
5.2.5 Viewing the System Event Log (SEL) 66
5.2.6 Updating the NIC configuration file in a Linux/VMware OS 67
5.2.7 Resuming BitLocker functionality 68
5.2.8 Performing a RAID array rebuild 69
5.2.9 Looking up for MAC/WWN addresses 70
5.2.10 Using the Chassis ID Prom Tool 71
5.2.11 Configuring LAN teaming 71
6 Power supply unit (PSU) 73
6.1 Safety notes 73
6.2 Basic information 73
6.3 Replacing the standard PSU 73
Content
TX1310 M5 Upgrade and Maintenance Manual

7 Hard disk drives (HDD) 81
7.1 Safety notes 81
7.2 Basic information 82
7.3 2.5-inch HDD/SSD configurations 83
7.3.1 Installing a 2.5-inch HDD module 83
7.3.2 Removing a 2.5-inch HDD module 86
7.3.3 Replacing a 2.5-inch HDD module 88
7.4 3.5-inch HDD configurations 89
7.4.1 Installing a 3.5-inch HDD module 89
7.4.2 Removing a 3.5-inch HDD module 92
7.4.3 Replacing a 3.5-inch HDD module 95
8 Fans 97
8.1 Safety notes 97
8.2 Basic information 97
8.3 Replacing the rear fan 98
8.4 Replacing the front fan 105
9 Expansion cards 111
9.1 Safety notes 111
9.2 Basic information 112
9.3 Handling slot brackets 113
9.3.1 Installing slot brackets 113
9.3.2 Removing slot brackets 116
9.4 Installing an expansion card 116
9.5 Removing an expansion card 119
Content
Upgrade and Maintenance Manual TX1310 M5

9.6 Replacing an expansion card 122
10 Main memory 125
10.1 Safety notes 125
10.2 Basic informations 126
10.3 Installing memory modules 128
10.4 Removing memory modules 129
10.5 Replacing memory modules 131
11 Processor (CPU) 133
11.1 Safety notes 133
11.2 Basic information 134
11.3 Upgrading or replacing the CPU 135
11.4 Replacing the heat sink 148
11.5 Handling the protectice cover 150
12 Accessible drives 157
12.1 Safety notes 157
12.2 Basic information 157
12.3 Optical disk drive (ODD) 158
12.3.1 Installing the ODD 158
12.3.2 Removing the ODD 162
12.3.3 Replacing the ODD 164
12.4 RDX drive 165
12.4.1 Installing the RDX backup drive 165
Content
TX1310 M5 Upgrade and Maintenance Manual

12.4.2 Removing the RDX backup drive 169
12.4.3 Replacing the RDX backup drive 171
13 Front panel and front USB 173
14 Serial interface 175
14.1 Safety notes 175
14.2 Installing the serial interface 175
14.3 Removing the serial interface 177
14.4 Replacing the serial interface 179
15 System board and components 181
15.1 Safety notes 181
15.2 Basic information 181
15.3 CMOS battery 182
15.3.1 Replacing the CMOS battery 182
15.4 Trusted Platform Module (TPM) 184
15.4.1 TPM kit 184
15.4.2 Installing the TPM 185
15.4.3 Removing the TPM 188
15.4.4 Replacing the TPM 192
15.5 M.2 SSD 194
15.5.1 Slots and bolts for M.2 SSDs 194
15.5.2 Installing an M.2 SSD 196
15.5.3 Removing an M.2 SSD 201
15.5.4 Replacing an M.2 SSD 204
15.6 System board 205
15.6.1 Replacing the system board 205
Content
Upgrade and Maintenance Manual TX1310 M5

16 Cables 217
16.1 Safety notes 217
16.2 Basic information 217
16.3 Replacing the system cable (accessible drives / top HDD
cage) 217
16.4 Replacing the HDD cable (bottom HDD cage) 220
17 Appendix A 225
17.1 Mechanical overview 225
17.1.1 Server front 225
17.1.2 Server rear 226
17.1.3 Server interior 227
17.2 Connectors and indicators 228
17.2.1 Connectors on the system board 228
17.2.2 Server front 230
17.2.2.1 Connectors on the server front 230
17.2.2.2 Indicators on the front panel 230
17.2.2.3 Indicators on the drives 231
17.2.3 Server rear 233
17.2.3.1 Connectors on the I/O panel 233
17.2.3.2 Indicators on the I/O panel 234
17.3 Onboard settings 235
17.4 Minimum startup configuration 236
18 Appendix B 239
18.1 Supplied documents 239
Content
TX1310 M5 Upgrade and Maintenance Manual

Content
Upgrade and Maintenance Manual TX1310 M5

1 Introduction
1.1 Concept and target groups of this manual
This upgrade and maintenance manual provides instructions for the following
procedures:
–Upgrading the server configuration by adding optional hardware
components.
–Upgrading the server configuration by replacing existing hardware
components with superior ones.
–Replacing defective hardware components.
This manual focuses on on-site maintenance tasks. It is recommended to
prepare each service assignment following remote diagnostics procedures, as
described in the "ServerView Suite Local Service Concept (LSC)" manual, see
"Documentation overview" on page 22.
CAUTION
The document at hand comprises procedures of a wide range of
complexity.
▶Check the profile of qualification for technicians before assigning
tasks.
▶Before you start, carefully read "Classification of procedures" on
page 18.
1.2 Notational conventions
The following notational conventions are used in this manual:
Text in bold Indicates references to names of interface
elements.
Text in monospace Indicates commands and text to be entered by
the user.
TX1310 M5 Upgrade and Maintenance Manual 15

"Quotation marks" Indicate names of chapters and terms that are
being emphasized.
▶ Describes activities that must be performed in
the order shown.
[Abc] Indicates keys on the keyboard.
CAUTION
Pay particular attention to texts marked with this
symbol. Failure to observe this warning may
endanger your life, destroy the system or lead
to the loss of data.
Indicates additional information, notes and tips.
Indicates the procedure category in terms of
complexity and qualification requirements, see
"Classification of procedures" on page 18.
Indicates the average task duration, see
"Average task duration" on page 21.
Introduction
16 Upgrade and Maintenance Manual TX1310 M5

2 Before you start
2.1 Basic information
2.1.1 Proceeding
Before you start any upgrade or maintenance task, proceed as follows:
▶Carefully read the safety instructions, see "Important information" on
page 25.
▶Make sure that all necessary manuals are available, see "About availability
of manuals" on page 22. Print the PDF files if required.
▶Make yourself familiar with the procedure categories, see "Classification of
procedures" on page 18.
▶Ensure that all required tools are available, see "Tools you need at hand" on
page 22.
2.1.2 Advanced Thermal Design (ATD)
The ATD option allows you to operate the system with a wider temperature
range either of 5 °C to 40 °C or 5 °C to 45 °C, depending on your system and
configuration.
This option can only be ordered from the
manufacturer and is indicated by the respective
logo on the identification rating plate.
CAUTION
▶In a system that is configured with ATD, only certain components
which support the respectively increased higher operating
temperature range may be installed and used. For applicable
restrictions, see the official configurator tool.
TX1310 M5 Upgrade and Maintenance Manual 17

2.1.3 Installing optional components
The operating manual of your server gives an introduction to server features
and provides an overview of available hardware options.
Use the Fujitsu ServerView Suite management software and the iRMC S5 web
interface to prepare hardware expansions. For more information about
ServerView Suite documentation, see "Documentation overview" on page 22.
Please see the following ServerView Suite topics:
–Operation
–Virtualization
–Maintenance
–Out-Of-Band Management
For the latest information on hardware options, see the hardware
configurator of your server, available online at the following address:
https://www.fujitsu.com/fts/products/computing/servers/primergy/
index.html
For Japan:
https://www.fujitsu.com/jp/products/computing/servers/primergy/
Please contact your local Fujitsu customer service partner for details on how to
order expansion kits or spare parts.
2.2 Classification of procedures
2.2.1 Assignment of unit categories
The complexity of maintenance procedures varies significantly. Procedures
have been assigned to one of three unit categories, indicating the level of
difficulty and required qualification.
At the beginning of each procedure, the involved unit category is indicated by
one of the symbols introduced in this section.
Before you start
18 Upgrade and Maintenance Manual TX1310 M5

Please ask your local Fujitsu service center for more information.
2.2.2 Customer Replaceable Units (CRU)
Customer Replaceable Units (CRU)
Customer Replaceable Units are intended for customer self service.
Components that the customer is entitled to replace may differ
according to the service form in his country.
For Japan:
https://www.fujitsu.com/jp/products/computing/servers/primergy/support/
repair.html
Peripherals that are handled as Customer Replaceable Units
–Keyboard
–Mouse
2.2.3 Upgrade and Repair Units (URU)
Upgrade and Repair Units (URU)
Upgrade and Repair Units are non hot-plug components that can be ordered
separately to be installed as options (Upgrade Units) or are available to the
customer through customer self service (Repair Units).
For Japan, customer allows only upgrade. For upgrade units as
customer replaceable, see:
https://www.fujitsu.com/jp/products/computing/servers/primergy/
Server management error messages will report defective Upgrade and
Repair Unit.
Before you start
TX1310 M5 Upgrade and Maintenance Manual 19

Upgrade and repair procedures involve shutting down and opening the server.
CAUTION
The device may be seriously damaged or cause damage if it is opened
without authorization or if repairs are attempted by unauthorized and
untrained personnel.
Components that are handled as Upgrade Units
–CPU (upgrade kits)
–ODDs
–Backup drives
–Expansion cards
–Memory modules
Components that are handled solely as Repair Units
–CMOS battery
–Non hot-plug fans
–Non hot-plug HDDs
2.2.4 Field Replaceable Units (FRU)
Field Replaceable Units (FRU)
Removing and installing Field Replaceable Units involves complex
maintenance procedures on integral server components. Procedures will
require shutting down and disassembling the server.
CAUTION
Maintenance procedures involving Field Replaceable Units must be
performed exclusively by Fujitsu service personnel or technicians
trained by Fujitsu. Please note that unauthorized interference with the
system will void the warranty and exempt the manufacturer from all
liability.
Before you start
20 Upgrade and Maintenance Manual TX1310 M5