Fujitsu ETERNUS DX Disk User manual

FUJITSU Storage
ETERNUS DX, ETERNUS AF
Configuration Guide -Server Connection-
(Fibre Channel) for Oracle VM Server for x86
P3AM-6612-14ENZ0

This page is intentionally left blank.

Preface
This manual briefly explains the operations that need to be performed by the user in order to connect an
ETERNUS DX/AF to a server running Oracle VM Server for x86 via a Fibre Channel interface.
This manual should be used in conjunction with any other applicable user manuals, such as those for the
ETERNUS DX/AF, server, OS, Fibre Channel cards, and drivers.
Refer to "Configuration Guide -Server Connection- Notations" for the notations used in this manual such as
product trademarks and product names. For storage systems that are supported by the OS, refer to the Server
Support Matrix of the ETERNUS DX/AF.
14th Edition
December 2017
The Contents and Structure of this Manual
This manual is composed of the following eight chapters.
•"Chapter 1 Workflow" (page 5)
This chapter describes how to connect the ETERNUS DX/AF storage systems to a server running Oracle VM
Server for x86.
•"Chapter 2 Checking the Server Environment" (page 8)
This chapter describes which servers can be connected to ETERNUS DX/AF storage systems.
•"Chapter 3 Notes" (page 9)
This chapter describes issues that should be noted when connecting the ETERNUS DX/AF storage systems
and server.
•"Chapter 4 Checking Fibre Channel Card Information" (page 10)
This chapter describes the Fibre Channel card WWNs that are required for ETERNUS DX/AF settings and Fi-
bre Channel switch settings.
•"Chapter 5 Installing and Setting Up ETERNUSmgr" (page 11)
This chapter describes how to install ETERNUSmgr.
•"Chapter 6 Setting Up the ETERNUS DX/AF" (page 12)
This chapter describes how to set up an ETERNUS DX/AF.
•"Chapter 7 Setting Up the Fibre Channel Switches" (page 13)
This chapter describes how to set up the Fibre Channel switches.
•"Chapter 8 Setting Up Oracle VM Server" (page 15)
This chapter describes how to set up Oracle VM Server.
Oracle VM Server Terminology
•Oracle VM Manager (OVM)
An application that manages the Oracle VM Server, virtual machines, and resources. This application can be
used via a web browser.
•Virtual Machine (VM)
A virtual machine (Guest OS) that is created in an Oracle VM Server.
3
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Table of Contents
Chapter 1 Workflow 5
Chapter 2 Checking the Server Environment 8
2.1 Servers ........................................................................................................................................... 8
2.2 Fibre Channel Switches................................................................................................................... 8
2.3 Fibre Channel Cards........................................................................................................................ 8
2.4 Connection Compatibility of ETERNUS DX/AF Storage Systems to Oracle VM Server ........................ 8
2.5 Virtual Machine.............................................................................................................................. 8
Chapter 3 Notes 9
3.1 Installation Notes........................................................................................................................... 9
3.2 ETERNUS DX/AF Setup Notes........................................................................................................... 9
3.3 Server Startup and Power Supply Control Notes.............................................................................. 9
Chapter 4 Checking Fibre Channel Card Information 10
Chapter 5 Installing and Setting Up ETERNUSmgr 11
Chapter 6 Setting Up the ETERNUS DX/AF 12
Chapter 7 Setting Up the Fibre Channel Switches 13
Chapter 8 Setting Up Oracle VM Server 15
8.1 Setting Up the Fibre Channel Cards .............................................................................................. 15
8.1.1 For Emulex Fibre Channel Cards..........................................................................................................................15
8.1.2 For QLogic Fibre Channel Cards...........................................................................................................................16
8.1.3 Creating an Initial RAM Disk ...............................................................................................................................20
8.1.4 Rebooting the OS................................................................................................................................................20
8.2 Turning On the Devices ................................................................................................................ 20
8.3 Checking LUN Status .................................................................................................................... 21
8.4 Checking the Multipath ................................................................................................................ 22
8.5 Installing and Setting Oracle VM Manager ................................................................................... 22
4
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 1
Workflow
This chapter describes how to connect the ETERNUS DX/AF to a server running Oracle VM Server. This manual
explains how to perform various operations not referenced in other documents.
Required Documents
•"Server Support Matrix"
•"Server Support Matrix for FC-SWITCH"
•"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETERNUS DX/AF
to be connected
•"Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel Switch Settings"
•"ETERNUS Web GUI User's Guide"
•"ETERNUSmgr Install Guide"
•"ETERNUSmgr User Guide"
•Manuals supplied with the Fibre Channel card and software
Workflow
Checking the Fibre Channel Card Information
Obtain the WWN information of the Fibre Channel card.
•"Chapter 4 Checking Fibre Channel Card Information" (page 10)
5
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Installing ETERNUSmgr and Setting Up the ETERNUS DX/AF
If ETERNUSmgr is to be used, install it and set up the ETERNUS DX/AF.
•"Chapter 5 Installing and Setting Up ETERNUSmgr" (page 11)
•"Chapter 6 Setting Up the ETERNUS DX/AF" (page 12)
•Checking the setup and maintenance operations
-"ETERNUS Web GUI User's Guide"
•Installing ETERNUSmgr
-"ETERNUSmgr Install Guide"
•Checking the ETERNUSmgr operational procedures
-"ETERNUSmgr User Guide"
•Setting up the ETERNUS DX/AF
-"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETER-
NUS DX/AF to be connected
Setting Up the Fibre Channel Switches
If a Fibre Channel switch is to be used, set it up now.
•"Chapter 7 Setting Up the Fibre Channel Switches" (page 13)
•Setting up the Fibre Channel switches
-"Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel Switch Settings"
•Checking the Fibre Channel switch connection requirements
-"Server Support Matrix for FC-SWITCH"
Setting Up Oracle VM Server
Set up Oracle VM Server to connect to the ETERNUS DX/AF.
•"Chapter 8 Setting Up Oracle VM Server" (page 15)
•Setting up Oracle VM Server and the Fibre Channel card
-"8.1 Setting Up the Fibre Channel Cards" (page 15)
•Checking the Fibre Channel card driver versions
-"Server Support Matrix"
Chapter 1 Workflow
6
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Checking the LUNs
Check whether the server recognizes the LUNs of the ETERNUS DX/AF and set up the LUNs so that they
can be used on Oracle VM Server.
•"8.3 Checking LUN Status" (page 21)
Checking the Multipath
Use the Oracle VM Server multipath to perform a redundant configuration.
•"8.4 Checking the Multipath" (page 22)
Installing and Setting Oracle VM Manager
Set up the Oracle VM Manager.
•"8.5 Installing and Setting Oracle VM Manager" (page 22)
Chapter 1 Workflow
7
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 2
Checking the Server Environment
Connection to servers is possible in the following environments.
Check the "Server Support Matrix" for server environment conditions.
2.1 Servers
Refer to "Server Support Matrix" and the following URL:
https://linux.oracle.com/hardware-certifications
2.2 Fibre Channel Switches
The Fibre Channel switches that can be connected depend on the connection configuration that is used (the
OS and the ETERNUS DX/AF). Refer to "Server Support Matrix for FC-SWITCH".
2.3 Fibre Channel Cards
Refer to the "Server Support Matrix".
2.4 Connection Compatibility of ETERNUS DX/AF Storage Systems
to Oracle VM Server
Refer to the "Server Support Matrix".
2.5 Virtual Machine
For details on the procedure and notes about installing a Virtual Machine that is supported by Oracle VM
Server, refer to the manuals that can be obtained on the following Oracle web-site:
https://linux.oracle.com/hardware-certifications
8
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 3
Notes
Note the following issues when connecting the ETERNUS DX/AF to a server.
3.1 Installation Notes
•To ensure reliable access to ETERNUS DX/AF storage systems, multipath configuration is recommended.
Setting up multiple access paths between the server and the ETERNUS DX/AF storage systems, then using
the Oracle VM Server multipath, provides improved access redundancy.
•Enable the virtualization support functions (Intel VT or AMD-V) of the server before installing Oracle VM
Server. For details on the settings, refer to the relevant manual of the server to be used.
•Install Oracle VM Server when the ETERNUS DX/AF is not connected to the server.
•The ETERNUS Multipath Driver does not need to be installed on the Oracle VM Server Virtual Machine. The
Oracle VM Server multipath driver provides path redundancy.
•When multiple paths are used, the Oracle VM Server multipath driver must be set. If a multipath driver is
not set, the Oracle VM Server multipath driver does not perform proper load balancing for the ETERNUS
DX/AF.
3.2 ETERNUS DX/AF Setup Notes
Host response must be set before the ETERNUS DX/AF is connected to the Oracle VM Server host.
3.3 Server Startup and Power Supply Control Notes
Before turning the server on, check that the ETERNUS DX/AF storage systems and Fibre Channel switches are
all "Ready". If the server is turned on and they are not "Ready", the server will not be able to recognize the
ETERNUS DX/AF storage systems.
Also, when the ETERNUS DX/AF power supply is being controlled by a connected server, make sure that the
ETERNUS DX/AF does not shut down before the connected servers. Similarly, the Fibre Channel switches must
also be turned off after the connected servers have been shut down. If turned off, data writes from the run-
ning server cannot be saved to the ETERNUS DX/AF storage systems, and already saved data may also be
affected.
9
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 4
Checking Fibre Channel Card Information
The WWNs of Fibre Channel cards are necessary when a system error occurs, when server access to the ETER-
NUS DX/AF is limited (such as when using the Host Affinity function), or when the ETERNUS DX/AF is connec-
ted to the server via Fibre Channel switches.
Use the methods described in the following examples to obtain the WWN information of the Fibre Channel
card to be used.
Example:
Check the WWN using the utilities that are provided by the Fibre Channel card vendors.
Emulex: LightPulse BIOS Utility
QLogic: Fast!UTIL
10
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 5
Installing and Setting Up ETERNUSmgr
If ETERNUSmgr is to be used, install it according to the directions given in the "ETERNUSmgr Install Guide".
After installation is complete, follow the instructions in "ETERNUSmgr User Guide" and set up ETERNUSmgr.
11
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 6
Setting Up the ETERNUS DX/AF
Set up the ETERNUS DX/AF storage systems using ETERNUS Web GUI or ETERNUSmgr.
ETERNUS DX/AF setup can be performed independently of server setup. For details on how to perform these
settings, refer to the following manuals.
•"Configuration Guide -Server Connection- Storage System Settings" that corresponds to the ETERNUS DX/AF
to be connected
•"ETERNUS Web GUI User's Guide" or "ETERNUSmgr User Guide"
12
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 7
Setting Up the Fibre Channel Switches
Perform the settings required to connect the ETERNUS DX/AF storage systems and server via the Fibre Chan-
nel switch, according to "Configuration Guide -Server Connection- (Fibre Channel) Fibre Channel Switch Set-
tings".
If the access path is set with ETERNUS SF Storage Cruiser, the Host Response settings are set to the default
values.
If the Host Response settings are changed from the default values, set the Host Response again.
The following examples show configurations in which a server is connected to a Fibre Channel switch with
zoning.
The following example shows a configuration for multiple servers.
Port2Port0 Port6Port4
Port3Port1 Port7Port5
Port2Port0 Port6Port4
Port3Port1 Port7Port5
ZONE1 ZONE2 ZONE3
ZONE4
Name : Server#1
Port1
Port0
Name : Server#2
Port1Port0
Cascading
line
FC switch FC switch
CM0 CM1
Name : RAID#1
ETERNUS DX/AF
Port1 Port1Port0 Port0
13
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

The following example shows a configuration for a single server.
Port2Port0 Port6Port4
Port3Port1 Port7Port5
Port2Port0 Port6Port4
Port3Port1 Port7Port5
Cascading
line
ZONE1
ZONE2
ZONE3 ZONE4
FC switch
Server
Port0 Port1
CM0 CM1
ETERNUS DX/AF
Port0 Port0 Port1Port1
FC switch
Chapter 7 Setting Up the Fibre Channel Switches
14
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Chapter 8
Setting Up Oracle VM Server
Set up Oracle VM Server to connect the ETERNUS DX/AF.
The settings described in this chapter are performed using Oracle VM Manager. Prepare a Oracle VM Manager
environment before setting up Oracle VM Server. For details on how to install and operate Oracle VM Manag-
er, refer to the Oracle documents.
8.1 Setting Up the Fibre Channel Cards
Perform Fibre Channel card settings.
8.1.1 For Emulex Fibre Channel Cards
This section explains how to install Emulex Fibre Channel cards in the Oracle VM Server host and how to con-
nect the ETERNUS DX/AF.
Since the standard driver that is supplied with the OS is used for the Fibre Channel driver, other drivers do
not need to be installed.
Use the following procedure to set the drive parameters.
Use an editor such as "vi" to add the setting values to the configuration file.
•Configuration file
OS Configuration file
Oracle VM Server 3.3 Any file (.conf) in /etc/modprobe.d/
Oracle VM Server 3.2 /etc/modprobe.conf
Oracle VM Server 3.1 /etc/modprobe.conf
Note that the setting values and items vary depending on the ETERNUS DX/AF that is used.
•Example:
options lpfc lpfc_lun_queue_depth=8 lpfc_link_speed=8 lpfc_topology=2
15
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

1Perform the following driver parameter settings for each model of ETERNUS DX/AF that is to be connec-
ted.
Driver parameter Setting value
lpfc_lun-queue-depth Arbitrary (*1)
(Up to 1024 for each FC port of the ETERNUS DX/AF)
lpfc_topology •For direct connections: 4
•For switch connections: 2
When a direct connection is used and the LinkSpeed is 16Gbit/s, select "2".
lpfc_link-speed (*2)
*1: Recommended value = 1024 ¸ (number of Fibre Channel ports that are connected to a single CA
port) ¸ number of LUNs
(Round the result down)
•Use the value of "8" if the actual result is lower. Use the maximum value if the actual result ex-
ceeds the maximum value of the OS or the driver.
•To achieve maximum system performance, this value can be changed according to the server
load and the peak operating times.
•The number of simultaneous command executions per CA port for the ETERNUS DX/AF is limited
to 1024. This value is used by multiple servers that share the CA port. A maximum of 1024 com-
mands can be executed per CA port.
*2: Use the following "lpfc_link_speed" setting values.
Fibre
Channel
card
transfer
rate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
32Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
16Gbit/s 16 16 8 4 — — 16 8 4
8Gbit/s 8 8 8 4 2 — 8 8 4
4Gbit/s — 4 4 4 2 1 4 4 4
2Gbit/s — — 2 2 2 1 — 2 2
2Shut down the server.
After the driver parameter settings are complete, shut down the Oracle VM Server, and then connect the
ETERNUS DX/AF to the server with cables.
8.1.2 For QLogic Fibre Channel Cards
This section explains how to install QLogic Fibre Channel cards in the Oracle VM Server host and how to con-
nect the ETERNUS DX/AF.
Chapter 8 Setting Up Oracle VM Server
8.1 Setting Up the Fibre Channel Cards
16
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

Since the standard driver that is supplied with the OS is used for the Fibre Channel driver, other drivers do
not need to be installed.
Use the procedure below to set the BIOS settings and the drive parameters for Fibre Channel cards.
1Turn the server on, and watch for the following message to be displayed, in order to confirm that the
BIOS version specified in "Server Support Matrix" is installed.
QLogic Corporation
QLAxxxx PCI Fibre Channel ROM BIOS Version 1.50
Copyright (C) QLogic Corporation 1993-2006. All right reserved.
www.qlogic.com
Press <CTRL-Q> for Fast!UTIL
If the BIOS version matches that specified in "Server Support Matrix", press the [Ctrl]+[Q] keys while the
above message is displayed.
If the BIOS version differs from that specified in "Server Support Matrix", download and install the BIOS
version specified in "Server Support Matrix" from the QLogic Corp. web-site.
When two or more Fibre Channel cards are installed, the [Select Host Adapter] window appears. Se-
lect the Fibre Channel card to be set in the window.
2Select [Configuration Settings] from the [Fast!UTIL Options] menu and press the [Enter] key.
The [Configuration Settings] menu appears.
Host Adapter Settings
Selectable Boot Settings
Restore Default Settings
Raw Nvram Data
Advanced Adapter Settings
Extended Firmware Settings
Configuration Settings
3Select the [Host Adapter Settings] item.
4Check the values that are set in the [Host Adapter Settings] or [Adapter Settings] window.
The setting values vary depending on the type of Fibre Channel card used. Refer to the following table.
If the displayed values are different from those given in the following table, adjust them.
Refer to the Fibre Channel card manual and/or QLogic Corp. web-site for details.
Chapter 8 Setting Up Oracle VM Server
8.1 Setting Up the Fibre Channel Cards
17
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

•HBA Parameter Settings List displayed in the [Host Adapter Settings] window or [Adapter Settings]
window
Parameter
Setting value
Remarks
2Gbit/s Fibre
Channel card
4Gbit/s Fibre
Channel card
8Gbit/s Fibre
Channel card
Host Adapter BIOS Disabled If the current pa-
rameter values
are different,
change them to
the indicated
values.
Frame Size 2048
Loop Reset Delay 5
Adapter Hard Loop ID Disabled
Hard Loop ID 0
Spinup Delay Disabled
Connection Options 0 (direct connection)
1 (switch connection)
Determined by
the connection
method.
Fibre Channel Tape Support Disabled If the current pa-
rameter values
are different,
change them to
the indicated
values.
Data Rate (*1)
*1: Use the following "Data Rate" setting values
Fibre
Channel
card
transfer
rate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
32Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 8Gbit/s 4Gbit/s
8Gbit/s 4 4 4 3 1 — 4 3
4Gbit/s — 3 3 3 1 0 3 3
2Gbit/s — — 1 1 1 0 1 1
5Select [Advanced Adapter Settings].
Chapter 8 Setting Up Oracle VM Server
8.1 Setting Up the Fibre Channel Cards
18
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

6Check the values that are set in the [Advanced Adapter Settings] window or [Adapter Settings] window.
The setting values vary depending on the type of Fibre Channel card used. Refer to the following table.
If the displayed values are different from those given in the following table, adjust them.
Refer to the Fibre Channel card manual and/or QLogic Corp. web-site for details.
•Parameter Settings List displayed in the [Advanced Adapter Settings] window or [Adapter Settings]
window
Parameter
Setting value
Remarks
2Gbit/s Fibre
Channel card
4Gbit/s Fibre
Channel card
8Gbit/s Fibre
Channel card
Execution Throttle 16 16 65535 If the current pa-
rameter values
are different,
change them to
the indicated
values.
LUNs per Target 8 128 128
Enable LIP Reset No
Enable LIP Full Login Yes
Enable Target Reset Yes
Login Retry Count 8
Port Down Retry Count 30
Link Down Timeout 30
Extended Error Logging Disabled — —
RIO Operation Mode 0 — —
Operation Mode — 0 0
Interrupt Delay Timer 0
Enable Interrupt — No No
EV Controller Order — — Disabled
7Use an editor such as "vi" to add the setting values to the configuration file.
•Configuration file
OS Configuration file
Oracle VM Server 3.3 Any file (.conf) in /etc/modprobe.d/
Oracle VM Server 3.2 /etc/modprobe.conf
Oracle VM Server 3.1 /etc/modprobe.conf
•Example
When "8" is set for "ql2xmaxqdepth"
options qla2xxx ql2xmaxqdepth=8
Chapter 8 Setting Up Oracle VM Server
8.1 Setting Up the Fibre Channel Cards
19
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0

8.1.3 Creating an Initial RAM Disk
Create an initial RAM disk image file to match the kernel being used. Refer to manuals supplied with the
Fibre Channel cards for details.
8.1.4 Rebooting the OS
Reboot the OS.
8.2 Turning On the Devices
To turn on the connected devices, use the following procedure:
1Turn on the Fibre Channel switch power (if used).
2Check that the Ready LED (or equivalent) is lit on the Fibre Channel switch.
3Turn on the ETERNUS DX/AF.
4Check that the Ready LED is lit on the ETERNUS DX/AF.
5Turn on the server.
Chapter 8 Setting Up Oracle VM Server
8.2 Turning On the Devices
20
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle VM Server for x86
Copyright 2017 FUJITSU LIMITED
P3AM-6612-14ENZ0