Fujitsu ETERNUS DX60 S3 Technical manual

FUJITSU Storage
ETERNUS DX60 S3
Disk storage system
Site Planning Guide
P3AM-8982-03ENZ0

This page is intentionally left blank.

Preface
Fujitsu would like to thank you for purchasing our FUJITSU Storage ETERNUS DX60 S3 Disk storage system
(hereinafter referred to as ETERNUS DX).
The ETERNUS DX is designed to be connected to Fujitsu servers (Fujitsu M10, PRIMEQUEST, or PRIMERGY) or
non-Fujitsu servers.
This manual describes the environmental requirements that are necessary to install and use the ETERNUS
DX.
This manual is intended for use of the ETERNUS DX in regions other than Japan.
Please carefully review the information outlined in this manual.
Third Edition
October 2015
About This Manual
Organization
This manual is composed of the following two chapters:
•"Chapter 1 ETERNUS DX Installation" (page 10)
This chapter provides the installation specification of the ETERNUS DX.
•"Chapter 2 Rack Installation Specifications" (page 32)
This chapter provides the installation specification of racks.
Registered Trademarks and Trademarks
•All SPARC trademarks are used under license from SPARC International, Inc. and are trademarks or regis-
tered trademarks of that company in the United States and other countries.
•UNIX is a registered trademark of The Open Group in the United States and other countries.
•Microsoft, Windows, Windows Server, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•Oracle and Java are registered trademarks of Oracle and/or its affiliates.
•HP-UX is a trademark of Hewlett-Packard Company in the U.S. and other countries.
•Mozilla, Firefox, and the Mozilla and Firefox logos are trademarks or registered trademarks of the Mozilla
Foundation in the United States and other countries.
•Red Hat and Red Hat Enterprise Linux are trademarks of Red Hat, Inc., registered in the U.S. and other
countries.
•Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
•SUSE is a registered trademark of Novell, Inc. in the United States and other countries.
•IBM, AIX, and Tivoli are trademarks of International Business Machines Corporation, registered in many ju-
risdictions worldwide.
•VMware, VMware logos, Virtual SMP, and vMotion are either registered trademarks or trademarks of
VMware, Inc. in the U.S. and/or other countries.
•Arcserve is a registered trademark or trademark of Arcserve (USA), LLC.
•The company names, product names and service names mentioned in this document are registered trade-
marks or trademarks of their respective companies.
3
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Naming Conventions
■Product Names
•The following abbreviations are used for Microsoft® Windows Server®.
Product name Abbreviation
Microsoft® Windows Server® 2008 Datacenter
Microsoft® Windows Server® 2008 R2 Datacenter
Windows Server 2008
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 for Itanium-Based Systems
Microsoft® Windows Server® 2008 R2 for Itanium-Based Systems
Microsoft® Windows Server® 2008 HPC Edition
Microsoft® Windows Server® 2008 R2 HPC Edition
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Datacenter
Windows Server 2012
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 R2 Essentials
•The following abbreviations are used for Red Hat Linux.
Product name Abbreviation
Red Hat Enterprise Linux 5 (for x86)
Red Hat Enterprise Linux 5 (for Intel64)
Red Hat Enterprise Linux 5
Red Hat Enterprise Linux 6 (for x86)
Red Hat Enterprise Linux 6 (for Intel64)
Red Hat Enterprise Linux 6
Red Hat Enterprise Linux 7 (for Intel 64) Red Hat Enterprise Linux 7
■Symbols Used in This Manual
The following symbols are used throughout this manual:
This indicates information for the user to note when using the ETERNUS DX. Please be
sure to read this information.
This indicates supplementary and reference information.
Preface
4
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

■Abbreviations Used in This Manual
•"ETERNUS DX" refers to the FUJITSU Storage ETERNUS DX60 S3 Disk storage system.
•"CA" refers to a host interface module that is used in an ETERNUS DX to connect to a server.
•"Host Bus Adapter (HBA)" refers to an interface module that is normally used in a server to connect to
ETERNUS DX storage systems.
•Trademark symbols such as ™ and ® are omitted in this document.
Warning Signs
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material dam-
age. These signs are composed of a symbol and a message describing the recommended level of caution.
The following explains the symbol, its level of caution, and its meaning as used in this manual.
This symbol indicates the possibility of serious or fatal injury if the ETERNUS DX is not
used properly.
This symbol indicates the possibility of minor or moderate personal injury, as well as
damage to the ETERNUS DX and/or to other users and their property, if the ETERNUS DX
is not used properly.
This symbol indicates IMPORTANT information for the user to note when using the ETER-
NUS DX.
The following symbols are used to indicate the type of warnings or cautions being described.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION contents. Inside
the triangle and above it are details concerning the symbol (e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action which must be
avoided is both illustrated inside the barred circle and written above it (e.g. No Disas-
sembly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The required ac-
tion is both illustrated inside the black disk and written above it (e.g. Unplug).
Preface
5
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

How Warnings are Presented in This Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical
ribbon in the left margin, to distinguish this warning from ordinary descriptions.
A display example is shown here.
Warning level indicator
Warning type indicator
Warning details
•To avoid damaging the ETERNUS DX, pay attention to the following points
when cleaning the ETERNUS DX:
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS DX when using
cleaners, etc.
- Do not use alcohol or other solvents to clean the ETERNUS DX.
Warning layout ribbon
Example warning
CAUTION Do
Preface
6
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

Table of Contents
Chapter 1 ETERNUS DX Installation 10
1.1 Installation Specifications ............................................................................................................ 10
1.2 Storage System Dimensions ......................................................................................................... 12
1.3 Compliance Standards.................................................................................................................. 16
1.4 Package Size ................................................................................................................................ 17
1.5 Installation Area .......................................................................................................................... 18
1.6 Installation Environment.............................................................................................................. 19
1.6.1 Air Conditioning..................................................................................................................................................19
1.6.2 Installation Methods...........................................................................................................................................19
1.6.3 Load Bearing Capacity for Floors.........................................................................................................................20
1.7 Outlet/Socket Specifications ......................................................................................................... 21
1.7.1 Specifications for Optional Power Supply Products..............................................................................................21
1.7.2 Required Number of Outlets/Sockets...................................................................................................................25
1.7.3 Circuit Protectors.................................................................................................................................................25
1.7.4 Input Power Supply Lines....................................................................................................................................29
Chapter 2 Rack Installation Specifications 32
2.1 Rack Installation Requirements.................................................................................................... 32
2.1.1 Placement in the Rack ........................................................................................................................................32
2.1.2 Cable Connection ................................................................................................................................................33
2.2 Installable Racks .......................................................................................................................... 38
2.2.1 Fujitsu Racks.......................................................................................................................................................38
2.2.2 Non-Fujitsu Racks ...............................................................................................................................................38
7
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

List of Figures
Figure 1.1 2.5" Type Controller Enclosure Dimensions...............................................................................................12
Figure 1.2 3.5" Type Controller Enclosure Dimensions...............................................................................................13
Figure 1.3 2.5" Type Drive Enclosure Dimensions......................................................................................................14
Figure 1.4 3.5" Type Drive Enclosure Dimensions......................................................................................................15
Figure 1.5 Installation Area and Service Area ...........................................................................................................18
Figure 1.6 Power Distribution Units (1U) ..................................................................................................................23
Figure 1.7 Power Distribution Units (2U) ..................................................................................................................24
Figure 1.8 Breaking Characteristics of Distribution Board Circuit Protectors ..............................................................26
Figure 1.9 Example of a Power Supply Connection When a Power Distribution Unit (1U) Is Used .............................27
Figure 1.10 Example of a Power Supply Connection When a Power Distribution Unit (2U) Is Used .............................28
Figure 1.11 Example of a Power Supply Connection When a Power Distribution Unit Is Not Used...............................29
Figure 1.12 Dual-Line Power Supply (When Connecting to Power Sockets).................................................................29
Figure 1.13 Dual-Line Power Supply (When Connecting to a UPS Unit).......................................................................30
Figure 1.14 Single-Line Power Supply (When Connecting to Power Sockets) ..............................................................30
Figure 1.15 Single-line Power Supply (When Connecting to a UPS Unit).....................................................................30
Figure 1.16 Single-line Power Supply (When Connecting to a Power Socket and a UPS Unit) .....................................30
Figure 2.1 AC Cable Connection.................................................................................................................................33
Figure 2.2 Connection Example 1 (Connections in the Same Rack)...........................................................................34
Figure 2.3 Connection Example 2 (Connections in Multiple Racks)...........................................................................35
Figure 2.4 Connection Example 3 (Connections in the Same Rack)...........................................................................36
Figure 2.5 Connection Example 4 (Connections in Multiple Racks)...........................................................................37
Figure 2.6 Unit Installation Area ...............................................................................................................................39
8
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

List of Tables
Table 1.1 Installation Specifications ........................................................................................................................10
Table 1.2 Package Size (for Regions other than the EMEIA, North American, Central American, and Caribbean Re-
gions).......................................................................................................................................................17
Table 1.3 Rating of the Current for Each Power Cord................................................................................................21
Table 1.4 Specifications for AC200V Power Cords (for the EMEIA, North American, Central American, and Caribbean
Regions)...................................................................................................................................................22
Table 1.5 Specifications for AC200V Power Cords (for Regions other than the EMEIA, North American, Central Ameri-
can, and Caribbean Regions) ...................................................................................................................22
Table 1.6 Specifications for AC125V Power Cords (for Regions other than the EMEIA, North American, Central Ameri-
can, and Caribbean Regions) ...................................................................................................................22
Table 1.7 Specifications for AC100V and AC200V Power Cords (for Regions other than the EMEIA, North American,
Central American, and Caribbean Regions) ..............................................................................................23
Table 1.8 Power Distribution Unit (AC200-240V, 1U, 4 Outlets) Specifications ........................................................23
Table 1.9 Power Distribution Unit (AC200-240V, 2U, 12 Outlets) Specifications ......................................................24
Table 1.10 Power Distribution Unit (AC200-240V, 2U, 16 Outlets) Specifications ......................................................24
Table 1.11 Required Conditions for Distribution Board Circuit Protectors...................................................................25
Table 2.1 Enclosure Installation Order .....................................................................................................................32
Table 2.2 Usage of Cables for Connecting Enclosures...............................................................................................33
Table 2.3 Specifications for the Unit Installation Area .............................................................................................39
9
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

Chapter 1
ETERNUS DX Installation
This chapter explains the installation of the ETERNUS DX.
1.1 Installation Specifications
The following table shows the installation specifications of the ETERNUS DX.
Table 1.1 Installation Specifications
Item ETERNUS DX60 S3
Dimensions (W ´
D ´ H)
Controller enclosure 2.5" type 482 ´ 645 ´ 88mm (2U)
3.5" type 482 ´ 670 ´ 88mm (2U)
Drive enclosure 2.5" type 482 ´ 540 ´ 88mm (2U)
3.5" type 482 ´ 560 ´ 88mm (2U)
Power distribution unit 1U 435 ´ 148 ´ 38mm
2U (485 ´ 280 ´ 43mm) ´ 2 (*1)
Maximum weight
(*2)
Controller enclosure 2.5" type 35kg
3.5" type 35kg
Drive enclosure 2.5" type 35kg
3.5" type 35kg
Power distribution unit 1U 2kg
2U (6kg) ´ 2 (*1)
Power Voltage AC 100 – 120V, AC 200 – 240V
Phase Single
Frequency 50Hz/60Hz
Maximum power
consumption (*2)
Controller enclo-
sure
2.5" type AC 100 – 120V 610W (620VA)
AC 200 – 240V 600W (610VA)
3.5" type AC 100 – 120V 530W (540VA)
AC 200 – 240V 530W (540VA)
Drive enclosure 2.5" type AC 100 – 120V 430W (440VA)
AC 200 – 240V 430W (440VA)
3.5" type AC 100 – 120V 340W (350VA)
AC 200 – 240V 340W (350VA)
10
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

Item ETERNUS DX60 S3
Maximum heat
generation (*2)
Controller enclo-
sure
2.5" type AC 100 – 120V 2,200kJ/h
AC 200 – 240V 2,200kJ/h
3.5" type AC 100 – 120V 2,000kJ/h
AC 200 – 240V 2,000kJ/h
Drive enclosure 2.5" type AC 100 – 120V 1,600kJ/h
AC 200 – 240V 1,600kJ/h
3.5" type AC 100 – 120V 1,300kJ/h
AC 200 – 240V 1,300kJ/h
Maximum amount
of exhaust air
Controller enclosure 2.5" type 4.0m3/min
3.5" type 4.0m3/min
Drive enclosure 2.5" type 4.0m3/min
3.5" type 4.0m3/min
Environmental
conditions
Temperature Operating 10 – 40°C
Not operating 0 – 50°C
Shipping -40 – 60°C
Temperature gradient 15°C/Hr or less
Humidity Operating 20 – 80%RH
Not operating 8 – 80%RH
Shipping 8 – 90%RH
Humidity gradient 30%/day or less
Maximum wet bulb temperature 29°C
Altitude above sea level 0 – 3000m
Airborne dust 0.15mg/m3 or less
Gas concentration tolerance level Cl2: 3.4ppb or less, H2S: 7.1ppb or less,
SO2: 37ppb or less, NH3: 420ppb or less,
NO2: 52ppb or less, O3: 5ppb or less, HCl:
6.6ppb or less, HF: 3.6ppb or less
Oil vapor 0.2mg/m3 or less
Seawater (salt corrosion) If the ETERNUS DX is installed on the ocean
or premises within 0.5km from the coast,
necessary measures must be taken to pre-
vent salt corrosion.
Vibration limit Operating 400gal
Not operating 1,000gal
Noise emission
(*3)
Sound pressure level 49dB (A)
Sound power level 6.7B
*1: A 2U power distribution unit is composed of two 1U power distribution units.
*2: These values are for each drive enclosure when 24 drives are installed in a 2.5" type drive enclosure or
12 drives are installed in a 3.5" type drive enclosure.
*3: These values are measured when a single controller enclosure and drive enclosure are configured in an
environment in which the temperature is 23 ± 2°C.
Chapter 1 ETERNUS DX Installation
1.1 Installation Specifications
11
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.2 Storage System Dimensions
■Controller Enclosure Dimensions
●2.5" Type Controller Enclosure
The diagrams below show the dimensions of a 2.5" type controller enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.1 2.5" Type Controller Enclosure Dimensions
645mm88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
12
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

●3.5" Type Controller Enclosure
The diagrams below show the dimensions of a 3.5" type controller enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.2 3.5" Type Controller Enclosure Dimensions
670mm
88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
13
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

■Drive Enclosure Dimensions
●2.5" Type Drive Enclosure
The diagrams below show the dimensions of a 2.5" type drive enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.3 2.5" Type Drive Enclosure Dimensions
540mm
88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
14
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

●3.5" Type Drive Enclosure
The diagrams below show the dimensions of a 3.5" type drive enclosure.
The dimension values do not include any protruding parts (approximation).
Figure 1.4 3.5" Type Drive Enclosure Dimensions
560mm88mm
482mm
Top
Front
Side
Chapter 1 ETERNUS DX Installation
1.2 Storage System Dimensions
15
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.3 Compliance Standards
●Compliance Standards
•Product safety
UL60950-1, CSA-C22.2 No.60950-1, EN60950-1, IEC60950-1, TP TC 004/2011
•Electromagnetic Compatibility
CNS13438 (C6357) Class A, FCC CFR47 part 15 Class A, ICES-003 Class A, EN55022 Class A, VCCI Class A,
AS/NZS CISPR22 Class A, TP TC 020/2011
•Electromagnetic Immunity
EN55024
•CE marking
Electromagnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
•Environmental compliance
RoHS-compliant (Restriction of hazardous substances)
2011/65/EU
WEEE-compliant (Waste electrical and electronic equipment)
•80PLUS GOLD (power conversion efficiency)
Chapter 1 ETERNUS DX Installation
1.3 Compliance Standards
16
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.4 Package Size
The ETERNUS DX is shipped in cardboard boxes. These boxes may not fit through some doorways or eleva-
tors. To make sure that the ETERNUS DX can be moved to the installation site, carefully check the transport
route information.
The following table shows the package size and the maximum package weight of each component for re-
gions other than the EMEIA, North American, Central American, and Caribbean regions.
Table 1.2 Package Size (for Regions other than the EMEIA, North American, Central American, and Caribbean Re-
gions)
Component Package size (W ´ D ´ H) Maximum weight
Controller enclosure 2.5" type 600 ´ 760 ´ 240mm Approximately 40kg
3.5" type 600 ´ 760 ´ 240mm Approximately 40kg
Drive enclosure 2.5" type 600 ´ 660 ´ 240mm Approximately 40kg
3.5" type 600 ´ 660 ´ 240mm Approximately 40kg
Drive (*1) 2.5" drive 160 ´ 278 ´ 106mm Approximately 0.5kg
3.5" drive 189 ´ 300 ´ 116mm Approximately 1.2kg
Power distribution units 1U 570 ´ 710 ´ 160mm Approximately 4kg
2U (390 ´ 590 ´ 180mm) ´ 2 (Approximately 7kg) ´ 2
*1: When an order for optional drives to be installed in the factory is placed, enclosures are shipped with
the drives preinstalled.
When optional drives are ordered without preinstallation, each drive is shipped in an individual pack-
age.
Chapter 1 ETERNUS DX Installation
1.4 Package Size
17
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.5 Installation Area
This section explains the installation areas and the service areas that are required for an ETERNUS DX that is
installed in a Fujitsu 19-inch rack.
Secure service areas that are 850mm or more in the front and rear of the ETERNUS DX.
Figure 1.5 Installation Area and Service Area
850mm or more
850mm or more
ETERNUS DX
Rear service area
Front service area
Chapter 1 ETERNUS DX Installation
1.5 Installation Area
18
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.6 Installation Environment
Sufficient consideration of the installation environment should be taken to ensure proper use of the ETERNUS
DX. Using the ETERNUS DX in an environment that does not satisfy the installation environment require-
ments may cause a failure to occur with the ETERNUS DX.
1.6.1 Air Conditioning
It is important to consider the flows of cooling air (intake air and exhaust air) for the installation location of
the ETERNUS DX. The temperature in some ETERNUS DX storage systems may rise by taking in air exhausted
from other storage systems depending on how they are installed near each other. In addition, check if the
ambient temperature in the installation location always satisfies the usage environment temperature by tak-
ing into consideration the room size, whether other storage systems are installed, and how many people are
present in the room.
When installing air conditioning, consider the following:
●Ambient Temperature
An ETERNUS DX is cooled by taking in air through the front intakes and pushing out the exhaust air through
the rear of the ETERNUS DX. If the intake air temperature does not meet the ambient environment condi-
tions, a temperature error occurs and the power of the ETERNUS DX is shut down.
•Front intake air temperature
Make sure that the front intake air temperature is between 10 and 40°C.
•Rear exhaust air temperature
For example, when the intake air temperature is 40°C, the exhaust air temperature is 50°C or higher.
The necessary cooling capacity of air conditioning must be determined by taking the exhaust air cooling
into consideration.
Estimate the amount of heat in the exhaust air from the ETERNUS DX by using the heat generation amount
and exhaust air amount that are listed in "1.1 Installation Specifications" (page 10).
1.6.2 Installation Methods
•Perform one of the following rack installation methods to ensure the safe use of an ETERNUS DX that is
installed in a rack:
-To secure a rack, use a rack without stabilizers and secure it to the building with the leveling feet.
-If a rack is not to be secured, make sure to use a rack with stabilizers and use these stabilizers to prevent
the rack from toppling over.
•Which installation method should be used depends on the installation location, the floor conditions, and
the type of racks that are to be used. Contact your installation contractor for more details regarding instal-
lation and how the installation should actually be performed.
Chapter 1 ETERNUS DX Installation
1.6 Installation Environment
19
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0

1.6.3 Load Bearing Capacity for Floors
Make sure that the following relationship between the load bearing capacity of the floor and the weight of
the ETERNUS DX is maintained.
(Load bearing capacity of the floor) > (ETERNUS DX weight ¸ Installation area that includes service
areas)
If the condition above is not satisfied, additional measures are required to ensure sufficient load bearing ca-
pacity.
Contact your installation contractor for details about the necessary measures that must be taken.
Chapter 1 ETERNUS DX Installation
1.6 Installation Environment
20
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Site Planning Guide
Copyright 2015 FUJITSU LIMITED
P3AM-8982-03ENZ0