Fujitsu PRIMERGY S40-DF User manual

Server
PRIMERGY S40-DF
Capacity Extension
Xenia Fierley
Siemens Nixdorf Informationssysteme AG ICP CS PS QM 3
81730 München
e-mail: email: [email protected]
Tel.: [phone]
Fax: 0 700 / 372 00000
U41100-J-Z156-1-74
Sprachen: En
Edition May 2001

This manual is printed on
paper treated with
chlorine-free bleach.
Comments…Suggestions…Corrections…
The User Documentation Department would like to know
your opinion on this manual. Your feedback helps us to
optimize our documentation to suit your individual needs.
Fax forms for sending us your comments are included at
the back of the manual.
There you will also find the addresses of the relevant User
Documentation Department
Copyright and Trademarks
Copyright © 2001 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de

Ger an
English

U41100-J-Z156-1-74
Contents
1 PRIMERGY S40-DF capacity extension . . . . . . . . . . . . . 1
1.1 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Notational conventions . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3.2 ESD label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3.3 Notes on transportation . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Converting the PRIMERGY S40-DF . . . . . . . . . . . . . . . 5
1.4.1 Removing and mounting the door . . . . . . . . . . . . . . . . . 8
1.4.2 Removing and mounting the side or top cover . . . . . . . . . . 9
1.4.3 Removing and mounting the protective shield . . . . . . . . . . 10
1.4.4 Converting the internal configuration . . . . . . . . . . . . . . 11
1.4.5 Installing the LVD extender board . . . . . . . . . . . . . . . . 17
1.4.6 Connecting the capacity extension . . . . . . . . . . . . . . . 19
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

U41100-J-Z156-1-74 1
1 PRIMERGY S40-DF capacity
extension
The PRIMERGY S40-DF is the active component in the PRIMERGY S40 family
of storage subsystems. The integrated disk array controller allows you to extend
storage capacity using additional externally-connected passive PRIMERGY
S40-ES storage devices. Two of these so-called “daisy-chain” configurations,
i.e., with one or three PRIMERGY S40-ES units, are supported (see also the
chapter on “Configurations” in the PRIMERGY S40-DF Operating Manual).
In order to use a configuration with three external PRIMERGY S40-ES units,
you will need the 1-channel version of the PRIMERGY S40-DF.
This manual contains conversion instructions which describe the steps required
to prepare a PRIMERGY S40-DF (3-channel version) for capacity expansion
with three PRIMERGY S40-ES subsystems.
For more assistance in understanding the details here, see also the operating
instructions for the “PRIMERGY S40-DF Storage Subsystem”. Further relevant
information can be found in the manual “Safety, Warranty and Ergonomy“ (see
section “Related publications” on page 21).

2 U41100-J-Z156-1-74
Target group PRIMERGY S40-DF capacity extension
1.1 Target group
These conversion instructions are intended for those who are responsible for
installing hardware and for ensuring that the system runs smoothly (service
personnel, technicians and technical specialists).
You will therefore need to be familiar with the hardware and data transmission
concepts to understand the various activities described.
1.2 Notational conventions
bold type Used for emphasis in the body of the text
“quotation marks” Used for references to other chapters, sections or
manuals
ÊIdentifies an action that you need to take
VCAUTION! Indicates a warning which, if not observed, could
jeopardize your health or the proper functionality of
the system
IIndicates additional information, notes and tips
Table 1: Notational conventions

U41100-J-Z156-1-74 3
PRIMERGY S40-DF capacity extension Important notes
1.3 Important notes
1.3.1 Notes on safety
Please observe all the safety instructions given in the documentation of the
PRIMERGY S40-DF as well as the following notes:
VCAUTION!
●The actions described here should only be performed by technicians,
service personnel or technical specialists. Any failure to observe the
guidelines in this manual could expose the user to considerable risks
(electric shock, fire hazards) and could also damage the equipment.
Note that any unauthorized opening of the device will result in the
invalidation of the warranty and exclusion from all liability.
●Make sure that no objects (such as bracelets or paper clips) or liquids
fall into the device, as this may result in an electric shock or a short
circuit.
●Before opening the unit, switch off the device and then pull out the
power plugs.
●Note that switching off the device does not disconnect it from the
power supply. To ensure that the device is fully disconnected from the
power supply, you must pull out the power plugs.
1.3.2 ESD label
Systems and components which might be damaged by electrostatic discharge
(ESD) may be marked with the following label:
Figure 1: Label indicating ESD-sensitive devices

4 U41100-J-Z156-1-74
Important notes PRIMERGY S40-DF capacity extension
When handling ESD-sensitive devices, it is essential that you observe the
following guidelines:
ÊYou must electrostatically discharge yourself (e.g. by touching a grounded
object) before handling such components.
ÊAny devices or tools that are used must be free from electrostatic charge.
ÊPull out the power plug before mounting or dismounting ESD-sensitive
devices.
ÊESD-sensitive devices should only be held at the edges.
ÊDo not touch any pins, connectors or circuits on an ESD-sensitive device.
ÊWhen installing boards, make sure that you use an electrostatic wrist-band
or some other suitable grounding cable that connects you to the external
housing of the system unit.
ÊPlace all components on a pad which is free from electrostatic charge.
IFor detailed instructions on handling ESD-sensitive modules, please
read the German documentation “Richtlinie zur Handhabung von
elektrostatisch gefährdeten Bauelementen und Baugruppen (EGB)" or
“ITS-Rundschreiben Nr. 4/95".
IAn ESD kit can be ordered from SIEMENS sales or an authorized
distributor under the order number 8501 and stock-no. 06431046.
1.3.3 Notes on transportation
IThe storage subsystem should always be transported only in its original
packaging or in some other suitable packaging that protects it against
shock or impact.
It should only be unpacked at the deployment site.
If you need to physically lift or transport the storage subsystem, ask
someone to assist you.