Fujitsu MHN2100AT - Mobile 10 GB Hard Drive User manual

C141-E120-02EN
MHN2300AT, MHN2200AT,
MHN2150AT, MHN2100AT
DISK DRIVES
PRODUCT MANUAL

C141-E120-02EN
FOR SAFE OPERATION
Handling of This Manual
This manual contains important information for using this product. Read thoroughly before using
the product. Use this product only after thoroughly reading and understanding especially the
section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully.
FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering
damage to their property. Use the product according to this manual.
IMPORTANT NOTE TO USERS
READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO
USERS, BYSTANDERS OR PROPERTY.
While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU
assumes no liability to any party for any damage caused by any error or omission contained in this
manual, its updates or supplements, whether such errors or omissions result from negligence,
accident, or any other cause. In addition, FUJITSU assumes no liability with respect to the
application or use of any product or system in accordance with the descriptions or instructions
contained herein; including any liability for incidental or consequential damages arising therefrom.
FUJITSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION
CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.
FUJITSU reserves the right to make changes to any products described herein without further
notice and without obligation.
This product is designed and manufactured for use in standard applications such as office work,
personal devices and household appliances. This product is not intended for special uses (atomic
controls, aeronautic or space systems, mass transport vehicle operating controls, medical devices
for life support, or weapons firing controls) where particularly high reliability requirements exist,
where the pertinent levels of safety are not guaranteed, or where a failure or operational error could
threaten a life or cause a physical injury (hereafter referred to as "mission-critical" use). Customers
considering the use of these products for mission-critical applications must have safety-assurance
measures in place beforehand. Moreover, they are requested to consult our sales representative
before embarking on such specialized use.
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media without
the express written permission of Fujitsu Limited.
All Rights Reserved, Copyright FUJITSU LIMITED 2001

C141-E120-02EN
Revision History
(1/1)
Edition Date Revised section (*1)
(Added/Deleted/Altered)
Details
01 2001-02-28 — —
Ta le 1.2 Order No. was added.
Ta le 1.3 Current and power dissipation were
changed.
Ta le 1.6 Condition and specification were
corrected.
1.10 Load/Unload Function "Soft Reset"was deleted.
3-1 page Account was added.
3.1 Dimension Tolerance was corrected.
(6)Handling caution 3.2 Recommended equipment were changed.
Ta le 5.3 Command was added.
CHAPTER 5 Interface Changed and added.
02 2001-09-03
CHAPTER 6 Operation Changed and added.
*1 Section(s) with asterisk (*) refer to the previous edition when those were deleted.

This page is intentionally left blank.

C141-E120-02EN i
Preface
This manual describes the MHN Series, 2.5-inch hard disk drives. These drives
have a built-in controller that is compatible with the ATA interface.
This manual describes the specifications and functions of the drives and explains
in detail how to incorporate the drives into user systems. This manual assumes
that the reader has a basic knowledge of hard disk drives and their implementations
in computer systems.
This manual consists of seven chapters and sections explaining the special
terminology and abbreviations used in this manual:
Overview of Manual
CHAPTER 1 Device Overview
This chapter gives an overview of the MHN Series and describes their features.
CHAPTER 2 Device Configuration
This chapter describes the internal configurations of the MHN Series and the
configuration of the systems in which they operate.
CHAPTER 3 Installation Conditions
This chapter describes the external dimensions, installation conditions, and switch
settings of the MHN Series.
CHAPTER 4 Theory of Device Operation
This chapter describes the operation theory of the MHN Series.
CHAPTER 5 Interface
This chapter describes the interface specifications of the MHN Series.
CHAPTER 6 Operations
This chapter describes the operations of the MHN Series.
Terminology
This section explains the special terminology used in this manual.
Abbreviation
This section gives the meanings of the definitions used in this manual.

Preface
ii C141-E120-02EN
Conventions for Alert Messages
This manual uses the following conventions to show the alert messages. An alert
message consists of an alert signal and alert statements. The alert signal consists
of an alert symbol and a signal word or just a signal word.
The following are the alert signals and their meanings:
This indicates a hazardous situation could result in
minor or moderate personal injury if the user does
not perform the procedure correctly. This alert
signal also indicates that damages to the product or
other property may occur if the user does not perform
the procedure correctly.
This indicates information that could help the user
use the product more efficiently.
In the text, the alert signal is centered, followed below by the indented message. A
wider line space precedes and follows the alert message to show where the alert
message begins and ends. The following is an example:
(Example)
Data corruption: Avoid mounting the disk drive near strong
magnetic sources such as loud speakers. Ensure that the disk drive is
not affected by external magnetic fields.
The main alert messages in the text are also listed in the “Important Alert Items.”
Operating Environment
This product is designed to be used in offices or computer rooms.
For details regarding the operating environment of use, refer to the
(Cnnn-Xnnn) and the
(Cnnn-Xnnn).
Attention
Please forward any comments you may have regarding this manual.
To make this manual easier for users to understand, opinions from readers are
needed. Please write your opinions or requests on the Comment at the back of this
manual and forward it to the address described in the sheet.

Preface
C141-E120-02EN iii
Liability Exception
“Disk drive defects” refers to defects that involve adjustment, repair, or
replacement.
Fujitsu is not liable for any other disk drive defects, such as those caused by user
misoperation or mishandling, inappropriate operating environments, defects in the
power supply or cable, problems of the host system, or other causes outside the
disk drive.

This page is intentionally left blank.

C141-E120-02EN v
Important Alert Items
Important Alert Messages
The important alert messages in this manual are as follows:
A hazardous situation could result in minor or moderate personal
injury if the user does not perform the procedure correctly. Also,
damage to the product or other property, may occur if the user does not
perform the procedure correctly.
Task Alert message Page
Normal Operation Data corruption: Avoid mounting the disk near strong
magnetic sources such as loud speakers. Ensure that the disk
drive is not affected by external magnetic fields.
Damage: Do not press the cover of the disk drive. Pressing
it too hard, the cover and the spindle motor contact, which
may cause damage to the disk drive.
Static: When handling the device, disconnect the body
ground (500 kΩor greater). Do not touch the printed circuit
board, but hold it by the edges.
3-7

This page is intentionally left blank.

C141-E120-02EN vii
Manual Organization
MHN2300AT, MHN2200AT,
MHN2150AT, MHN2100AT
DISK DRIVES
PRODUCT MANUAL
(C141-E120)
<This manual>
• Device Overview
• Device Configuration
• Installation Conditions
• Theory of Device Operation
• Interface
• Operations
MHN2300AT, MHN2200AT,
MHN2150AT, MHN2100AT
DISK DRIVES
MAINTENANCE MANUAL
(C141-E120)
• Maintenance and Diagnosis
• Removal and Replacement Procedure

This page is intentionally left blank.

C141-E120-02EN ix
Contents
CHAPTER 1 Device Overview........................................................................1-1
1.1 Features 1-2
1.1.1 Functions and performance 1-2
1.1.2 Adaptability 1-2
1.1.3 Interface 1-3
1.2 Device Specifications 1-4
1.2.1 Specifications summary 1-4
1.2.2 Model and product number 1-5
1.3 Power Requirements 1-5
1.4 Environmental Specifications 1-7
1.5 Acoustic Noise 1-8
1.6 Shock and Vibration 1-8
1.7 Reliability 1-9
1.8 Error Rate 1-10
1.9 Media Defects 1-10
1.10 Load/Unload Function 1-10
CHAPTER 2 Device Configuration ................................................................2-1
2.1 Device Configuration 2-2
2.2 System Configuration 2-4
2.2.1 ATA interface 2-4
2.2.2 1 drive connection 2-4
2.2.3 2 drives connection 2-4

Contents
xC141-E120-02EN
CHAPTER 3 Installation Conditions ............................................................. 3-1
3.1 Dimensions 3-2
3.2 Mounting 3-3
3.3 Cable Connections 3-9
3.3.1 Device connector 3-9
3.3.2 Cable connector specifications 3-10
3.3.3 Device connection 3-10
3.3.4 Power supply connector (CN1) 3-11
3.4 Jumper Settings 3-11
3.4.1 Location of setting jumpers 3-11
3.4.2 Factory default setting 3-12
3.4.3 Master drive-slave drive setting 3-12
3.4.4 CSEL setting 3-13
CHAPTER 4 Theory of Device Operation..................................................... 4-1
4.1 Outline 4-2
4.2 Subassemblies 4-2
4.2.1 Disk 4-2
4.2.2 Head 4-2
4.2.3 Spindle 4-3
4.2.4 Actuator 4-3
4.2.5 Air filter 4-3
4.3 Circuit Configuration 4-4
4.4 Power-on Sequence 4-7
4.5 Self-calibration 4-8
4.5.1 Self-calibration contents 4-8
4.5.2 Execution timing of self-calibration 4-9
4.5.3 Command processing during self-calibration 4-10
4.6 Read/write Circuit 4-10
4.6.1 Read/write preamplifier (HDIC) 4-10

Contents
C141-E120-02EN xi
4.6.2 Write circuit 4-10
4.6.3 Read circuit 4-13
4.6.4 Digital PLL circuit 4-14
4.7 Servo Control 4-15
4.7.1 Servo control circuit 4-15
4.7.2 Data-surface servo format 4-18
4.7.3 Servo frame format 4-20
4.7.4 Actuator motor control 4-21
4.7.5 Spindle motor control 4-22
CHAPTER 5 Interface .....................................................................................5-1
5.1 Physical Interface 5-2
5.1.1 Interface signals 5-2
5.1.2 Signal assignment on the connector 5-3
5.2 Logical Interface 5-6
5.2.1 I/O registers 5-7
5.2.2 Command block registers 5-8
5.2.3 Control block registers 5-13
5.3 Host Commands 5-13
5.3.1 Command code and parameters 5-14
5.3.2 Command descriptions 5-16
5.3.3 Error posting 5-88
5.4 Command Protocol 5-90
5.4.1 PIO Data transferring commands from device to host 5-90
5.4.2 PIO Data transferring commands from host to device 5-92
5.4.3 Commands without data transfer 5-94
5.4.4 Other commands 5-96
5.4.5 DMA data transfer commands 5-96
5.5 Ultra DMA Feature Set 5-99
5.5.1 Overview 5-99
5.5.2 Phases of operation 5-100
5.5.3 Ultra DMA data in commands 5-100

Contents
xii C141-E120-02EN
5.5.3.1 Initiating an Ultra DMA data in burst 5-100
5.5.3.2 The data in transfer 5-101
5.5.3.3 Pausing an Ultra DMA data in burst 5-101
5.5.3.4 Terminating an Ultra DMA data in burst 5-102
5.5.4 Ultra DMA data out commands 5-105
5.5.4.1 Initiating an Ultra DMA data out burst 5-105
5.5.4.2 The data out transfer 5-105
5.5.4.3 Pausing an Ultra DMA data out burst 5-106
5.5.4.4 Terminating an Ultra DMA data out burst 5-107
5.5.5 Ultra DMA CRC rules 5-109
5.5.6 Series termination required for Ultra DMA 5-110
5.6 Timing 5-111
5.6.1 PIO data transfer 5-111
5.6.2 Multiword data transfer 5-112
5.6.3 Ultra DMA data transfer 5-113
5.6.3.1 Initiating an Ultra DMA data in burst 5-113
5.6.3.2 Ultra DMA data burst timing requirements 5-114
5.6.3.3 Sustained Ultra DMA data in burst 5-117
5.6.3.4 Host pausing an Ultra DMA data in burst 5-118
5.6.3.5 Device terminating an Ultra DMA data in burst 5-119
5.6.3.6 Host terminating an Ultra DMA data in burst 5-120
5.6.3.7 Initiating an Ultra DMA data out burst 5-121
5.6.3.8 Sustained Ultra DMA data out burst 5-122
5.6.3.9 Device pausing an Ultra DMA data out burst 5-123
5.6.3.10 Host terminating an Ultra DMA data out burst 5-124
5.6.3.11 Device terminating an Ultra DMA data in burst 5-125
5.6.4 Power-on and reset 5-126
CHAPTER 6 Operations................................................................................. 6-1
6.1 Device Response to the Reset 6-2
6.1.1 Response to power-on 6-2
6.1.2 Response to hardware reset 6-3
6.1.3 Response to software reset 6-5
6.1.4 Response to diagnostic command 6-6

Contents
C141-E120-02EN xiii
6.2 Power Save 6-7
6.2.1 Power save mode 6-7
6.2.2 Power commands 6-8
6.3 Defect Management 6-9
6.3.1 Spare area 6-9
6.3.2 Alternating defective sectors 6-9
6.4 Read-Ahead Cache 6-11
6.4.1 Data buffer configuration 6-12
6.4.2 Caching operation 6-12
6.4.3 Usage of read segment 6-14
6.4.3.1 Mis-hit (no hit) 6-14
6.4.3.2 Sequential read 6-15
6.4.3.3 Full hit (hit all) 6-18
6.4.3.4 Partially hit 6-19
6.5 Write Cache 6-20
Glossary .................................................................................................GL-1
Acronyms and Abbreviations.........................................................................AB-1

Contents
xiv C141-E120-02EN
Illustrations
Figures
Figure 1.1 Current fluctuation (Typ.) at +5V when power is turned on 1-7
Figure 2.1 Disk drive outerview 2-2
Figure 2.2 Configuration of disk media heads 2-3
Figure 2.3 1 drive system configuration 2-4
Figure 2.4 2 drives configuration 2-4
Figure 3.1 Dimensions 3-2
Figure 3.2 Orientation 3-3
Figure 3.3 Mounting frame structure 3-4
Figure 3.4 Location of breather 3-5
Figure 3.5 Surface temperature measurement points 3-6
Figure 3.6 Service area 3-7
Figure 3.7 Handling cautions 3-8
Figure 3.8 Connector locations 3-9
Figure 3.9 Cable connections 3-10
Figure 3.10 Power supply connector pins (CN1) 3-11
Figure 3.11 Jumper location 3-11
Figure 3.12 Factory default setting 3-12
Figure 3.13 Jumper setting of master or slave drive 3-12
Figure 3.14 CSEL setting 3-13
Figure 3.15 Example (1) of Cable Select 3-13
Figure 3.16 Example (2) of Cable Select 3-14
Figure 4.1 Head structure 4-3
Figure 4.2 Power Supply Configuration 4-5
Figure 4.3 Circuit Configuration 4-6
Figure 4.4 Power-on operation sequence 4-8
Figure 4.5 Read/write circuit block diagram 4-12
Figure 4.6 Frequency characteristic of programmable filter 4-13
Figure 4.7 Block diagram of servo control circuit 4-15
Figure 4.8 Physical sector servo configuration on disk surface 4-19
Figure 4.9 Servo frame format 4-20
Figure 5.1 Interface signals 5-2

Contents
C141-E120-02EN xv
Figure 5.2 Execution example of READ MULTIPLE command 5-19
Figure 5.3 Read Sector(s) command protocol 5-91
Figure 5.4 Protocol for command abort 5-92
Figure 5.5 WRITE SECTOR(S) command protocol 5-94
Figure 5.6 Protocol for the command execution without data transfer 5-95
Figure 5.7 Normal DMA data transfer 5-98
Figure 5.8 Ultra DMA termination with pull-up or pull-down 5-110
Figure 5.9 PIO data transfer timing 5-111
Figure 5.10 Multiword DMA data transfer timing (mode 2) 5-112
Figure 5.11 Initiating an Ultra DMA data in burst 5-113
Figure 5.12 Sustained Ultra DMA data in burst 5-117
Figure 5.13 Host pausing an Ultra DMA data in burst 5-118
Figure 5.14 Device terminating an Ultra DMA data in burst 5-119
Figure 5.15 Host terminating an Ultra DMA data in burst 5-120
Figure 5.16 Initiating an Ultra DMA data out burst 5-121
Figure 5.17 Sustained Ultra DMA data out burst 5-122
Figure 5.18 Device pausing an Ultra DMA data out burst 5-123
Figure 5.19 Host terminating an Ultra DMA data out burst 5-124
Figure 5.20 Device terminating an Ultra DMA data out burst 5-125
Figure 5.21 Power-on Reset Timing 5-126
Figure 6.1 Response to power-on 6-3
Figure 6.2 Response to hardware reset 6-4
Figure 6.3 Response to software reset 6-5
Figure 6.4 Response to diagnostic command 6-6
Figure 6.5 Sector slip processing 6-10
Figure 6.6 Alternate cylinder assignment 6-11
Figure 6.7 Data buffer configuration 6-12
Tables
Table 1.1 Specifications 1-4
Table 1.2 Model names and product numbers 1-5
Table 1.3 Current and power dissipation 1-6
Table 1.4 Environmental specifications 1-7
Table 1.5 Acoustic noise specification 1-8
Table 1.6 Shock and vibration specification 1-8
Table 3.1 Surface temperature measurement points and standard values 3-6
Table 3.2 Cable connector specifications 3-10
Table 4.1 Write precompensation algorithm 4-11

Contents
xvi C141-E120-02EN
Table 5.1 Signal assignment on the interface connector 5-3
Table 5.2 I/O registers 5-7
Table 5.3 Command code and parameters 5-14
Table 5.4 Information to be read by IDENTIFY DEVICE command 5-32
Table 5.5 Features register values and settable modes 5-41
Table 5.6 Diagnostic code 5-53
Table 5.7 Features Register values (subcommands) and functions 5-65
Table 5.8 Format of device attribute value data 5-69
Table 5.9 Format of insurance failure threshold value data 5-69
Table 5.10 Log Directory Data Format 5-73
Table 5.11 SMART error log data format 5-74
Table 5.12 SMART self test log data format 5-76
Table 5.13 Contents of security password 5-77
Table 5.14 Contents of SECURITY SET PASSWORD data 5-81
Table 5.15 Relationship between combination of Identifier and Security level, and
operation of the lock function 5-81
Table 5.16 DEVICE CONFIGURATION IDENTIFY data structure 5-87
Table 5.17 Command code and parameters 5-88
Table 5.18 Ultra DMA data burst timing requirements 5-114
Table 5.19 Ultra DMA sender and recipient timing requirements 5-116