Fujitsu ETERNUS DX60 S3 User manual

FUJITSU Storage
ETERNUS DX60 S3
Disk storage system
Operation Guide (Basic)
P3AM-9012-01ENZ0

This page is intentionally left blank.

Preface
Fujitsu would like to thank you for purchasing our FUJITSU Storage ETERNUS DX60 S3 Disk storage system
(hereinafter referred to as ETERNUS DX).
The ETERNUS DX is designed to be connected to Fujitsu servers (Fujitsu M10, PRIMEQUEST, or PRIMERGY) or
non-Fujitsu servers.
This manual describes the operation management and maintenance of the ETERNUS DX.
This manual is intended for use of the ETERNUS DX in regions other than Japan.
Please carefully review the information outlined in this manual.
First Edition
December 2014
About This Manual
Organization
This manual is composed of the following six chapters:
•"Chapter 1 Component Name/LED Name" (page 12)
This chapter provides component names of the ETERNUS DX.
•"Chapter 2 Basic Operation" (page 30)
This chapter explains how to turn on and off the ETERNUS DX and how to operate the buttons on the oper-
ation panel.
•"Chapter 3 Storage System Monitoring" (page 40)
This chapter describes the status monitoring of the ETERNUS DX.
•"Chapter 4 Component Expansion/Function Enhancement " (page 44)
This chapter explains how to install drives and drive enclosures in the ETERNUS DX.
•"Chapter 5 Maintenance" (page 68)
This chapter describes maintenance once the ETERNUS DX starts to be operated.
•"Chapter 6 Troubleshooting" (page 69)
This chapter explains troubleshooting when errors occur on the ETERNUS DX.
3
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

Registered Trademarks and Trademarks
•All SPARC trademarks are used under license from SPARC International, Inc. and are trademarks or regis-
tered trademarks of that company in the United States and other countries.
•UNIX is a registered trademark of The Open Group in the United States and other countries.
•Microsoft, Windows, Windows Server, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•Oracle and Java are registered trademarks of Oracle and/or its affiliates.
•HP-UX is a trademark of Hewlett-Packard Company in the U.S. and other countries.
•Mozilla, Firefox, and the Mozilla and Firefox logos are trademarks or registered trademarks of the Mozilla
Foundation in the United States and other countries.
•Red Hat is a registered trademark of Red Hat, Inc. in the U.S. and other countries.
•Linux is a registered trademark of Linus Torvalds.
•SUSE is a registered trademark of Novell, Inc. in the United States and other countries.
•IBM, AIX, and Tivoli are trademarks of International Business Machines Corporation, registered in many ju-
risdictions worldwide.
•VMware, VMware logos, Virtual SMP, and vMotion are either registered trademarks or trademarks of
VMware, Inc. in the U.S. and/or other countries.
•ARCserve® products and logos are registered trademarks of CA Technologies.
•The company names, product names and service names mentioned in this document are registered trade-
marks or trademarks of their respective companies.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Naming Conventions
■Product Names
•The following abbreviations are used for Microsoft® Windows Server®.
Product name Abbreviation
Microsoft® Windows Server® 2008 Datacenter
Microsoft® Windows Server® 2008 R2 Datacenter
Windows Server 2008
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 for Itanium-Based Systems
Microsoft® Windows Server® 2008 R2 for Itanium-Based Systems
Microsoft® Windows Server® 2008 HPC Edition
Microsoft® Windows Server® 2008 R2 HPC Edition
Preface
4
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

Product name Abbreviation
Microsoft® Windows Server® 2012 Datacenter
Microsoft® Windows Server® 2012 R2 Datacenter
Windows Server 2012
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 R2 Essentials
•The following abbreviations are used for Red Hat Linux.
Product name Abbreviation
Red Hat Enterprise Linux 5 (for x86)
Red Hat Enterprise Linux 5 (for Intel64)
Red Hat Enterprise Linux 5
Red Hat Enterprise Linux 6 (for x86)
Red Hat Enterprise Linux 6 (for Intel64)
Red Hat Enterprise Linux 6
Red Hat Enterprise Linux 7 (for Intel 64) Red Hat Enterprise Linux 7
■Symbols Used in This Manual
The following symbol is used throughout this manual:
This indicates information for the user to note when using the ETERNUS DX. Please be
sure to read this information.
This indicates supplementary and reference information.
■Abbreviations Used in This Manual
•"ETERNUS DX" refers to the FUJITSU Storage ETERNUS DX60 S3 Disk storage system.
•"CA" refers to a host interface module that is used in an ETERNUS DX to connect to a server.
•"Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to
ETERNUS DX storage systems.
•Trademark symbols such as ™ and ® are omitted in this document.
Preface
5
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

Warning Signs
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material dam-
age. These signs are composed of a symbol and a message describing the recommended level of caution.
The following explains the symbol, its level of caution, and its meaning as used in this manual.
This symbol indicates the possibility of serious or fatal injury if the ETERNUS DX is not
used properly.
This symbol indicates the possibility of minor or moderate personal injury, as well as
damage to the ETERNUS DX and/or to other users and their property, if the ETERNUS DX
is not used properly.
This symbol indicates IMPORTANT information for the user to note when using the ETER-
NUS DX.
The following symbols are used to indicate the type of warnings or cautions being described.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION contents. Inside
the triangle and above it are details concerning the symbol (e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action which must be
avoided is both illustrated inside the barred circle and written above it (e.g. No Disas-
sembly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The required ac-
tion is both illustrated inside the black disk and written above it (e.g. Unplug).
Preface
6
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

How Warnings are Presented in This Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical
ribbon in the left margin, to distinguish this warning from ordinary descriptions.
A display example is shown here.
Warning level indicator
Warning type indicator
Warning details
•To avoid damaging the ETERNUS DX, pay attention to the following points
when cleaning the ETERNUS DX:
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS DX when using
cleaners, etc.
- Do not use alcohol or other solvents to clean the ETERNUS DX.
Warning layout ribbon
Example warning
CAUTION Do
Preface
7
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

Table of Contents
Chapter 1 Component Name/LED Name 12
1.1 Controller Enclosures.................................................................................................................... 12
1.1.1 Front...................................................................................................................................................................12
1.1.2 Rear ....................................................................................................................................................................13
1.1.3 Components (Front) ...........................................................................................................................................15
1.1.4 Components (Rear) ............................................................................................................................................18
1.2 3.5" Type Drive Enclosure ............................................................................................................. 22
1.2.1 Front...................................................................................................................................................................22
1.2.2 Rear ....................................................................................................................................................................22
1.2.3 Components (Front) ...........................................................................................................................................24
1.2.4 Components (Rear) ............................................................................................................................................25
1.3 Power Distribution Units (for Regions Other than EMEA&I).......................................................... 28
1.3.1 Power Distribution Units (1U).............................................................................................................................28
1.3.2 Power Distribution Units (2U).............................................................................................................................29
Chapter 2 Basic Operation 30
2.1 Powering On and Off .................................................................................................................... 30
2.1.1 Switching On and Off the Main Line Switch on the Power Distribution Unit (for Regions Other than EMEA&I) .......
.............................................................................................................................................................................30
2.1.2 Switching On and Off the PSU Switch on the Power Supply Unit .........................................................................33
2.1.3 Powering On .......................................................................................................................................................35
2.1.4 Powering Off.......................................................................................................................................................36
2.2 Using the FUNCTION Button ......................................................................................................... 38
Chapter 3 Storage System Monitoring 40
3.1 Checking LED Status..................................................................................................................... 40
3.2 Displaying Status via ETERNUS Web GUI....................................................................................... 40
3.3 Displaying Status via ETERNUS CLI................................................................................................ 41
3.4 Event Notification......................................................................................................................... 42
3.5 Audit Log...................................................................................................................................... 43
Chapter 4 Component Expansion/Function Enhancement 44
8
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

4.1 Installing Additional Drives .......................................................................................................... 44
4.1.1 Installable Drives ................................................................................................................................................44
4.1.2 Drive Handling Instructions ................................................................................................................................45
4.1.3 Additional Drive Installation Procedure ..............................................................................................................46
4.2 Installing Additional Drive Enclosures .......................................................................................... 51
4.2.1 Installable Drive Enclosures ................................................................................................................................51
4.2.2 Drive Enclosure Handling Instructions ................................................................................................................51
4.2.3 Additional Drive Enclosure Installation Procedure ..............................................................................................53
4.3 Adding Servers ............................................................................................................................. 61
4.3.1 RAID Group Creation ...........................................................................................................................................61
4.3.2 Volume Creation .................................................................................................................................................61
4.3.3 Connection Setup................................................................................................................................................63
Chapter 5 Maintenance 68
5.1 Periodic Backup............................................................................................................................ 68
5.2 Maintenance Service .................................................................................................................... 68
5.2.1 Maintenance Support Period ..............................................................................................................................68
5.2.2 Related Service ...................................................................................................................................................68
Chapter 6 Troubleshooting 69
6.1 Check List ..................................................................................................................................... 69
6.2 Required Information for Inquiries ............................................................................................... 77
Table of Contents
9
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

List of Figures
Figure 1.1 Front View of a 2.5" Type Controller Enclosure..........................................................................................12
Figure 1.2 Front View of a 3.5" Type Controller Enclosure..........................................................................................13
Figure 1.3 Rear View of a Controller Enclosure (When Only One Controller is Installed)............................................13
Figure 1.4 Rear View of a Controller Enclosure (When Two Controllers are Installed)................................................14
Figure 1.5 Operation Panel (Controller Enclosure) ....................................................................................................15
Figure 1.6 2.5" Drives................................................................................................................................................17
Figure 1.7 Drive Slot Numbers (2.5" Type Controller Enclosure) ................................................................................17
Figure 1.8 3.5" Drives................................................................................................................................................17
Figure 1.9 Drive Slot Numbers (3.5" Type Controller Enclosure) ................................................................................17
Figure 1.10 Controllers................................................................................................................................................18
Figure 1.11 Power Supply Unit (Controller Enclosure).................................................................................................21
Figure 1.12 Front View of a Drive Enclosure ................................................................................................................22
Figure 1.13 Rear View of a Drive Enclosure (When Only One I/O Module is Installed) .................................................22
Figure 1.14 Rear View of a Drive Enclosure (When Two I/O Modules are Installed) .....................................................23
Figure 1.15 Operation Panel (Drive Enclosure) ...........................................................................................................24
Figure 1.16 3.5" Drives................................................................................................................................................25
Figure 1.17 Drive Slot Numbers (Drive Enclosure).......................................................................................................25
Figure 1.18 I/O Module ...............................................................................................................................................26
Figure 1.19 Power Supply Unit (Drive Enclosure) ........................................................................................................27
Figure 1.20 Power Distribution Unit (AC200-240V, 1U, 4 Outlets)...............................................................................28
Figure 1.21 Power Distribution Unit (AC200-240V, 2U, 12 Outlets).............................................................................29
Figure 1.22 Power Distribution Unit (AC200-240V, 2U, 16 Outlets).............................................................................29
Figure 2.1 ON Position (Marked "|") of the Main Line Switches on a 1U Power Distribution Unit ..............................30
Figure 2.2 ON Position (Marked "|") of the Main Line Switches on a 2U Power Distribution Unit ..............................31
Figure 2.3 OFF Position (Marked "¡") of the Main Line Switches on a 1U Power Distribution Unit ...........................31
Figure 2.4 OFF Position (Marked "¡") of the Main Line Switches on a 2U Power Distribution Unit ...........................32
Figure 2.5 ON Position (Marked "|") of the PSU Switch on a Power Supply Unit ........................................................33
Figure 2.6 OFF Position (Marked "¡") of the PSU Switch of a Power Supply Unit ......................................................34
Figure 3.1 ETERNUS Web GUI Screen.........................................................................................................................40
Figure 3.2 Event Notification ....................................................................................................................................43
Figure 3.3 Audit Log..................................................................................................................................................43
10
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

List of Tables
Table 1.1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure)) ............................................15
Table 1.2 Status and Meanings of Each LED (Drive (Controller Enclosure)) .............................................................18
Table 1.3 Status and Meanings of Each LED (Controller) .........................................................................................19
Table 1.4 Status and Meanings of Each LED (Power Supply Unit (Controller Enclosure)).........................................21
Table 1.5 Status and Meanings of Each LED (Operation Panel) ...............................................................................24
Table 1.6 Status and Meanings of Each LED (Drive (Drive Enclosure)).....................................................................25
Table 1.7 Status and Meanings of Each LED (I/O Module) .......................................................................................26
Table 1.8 Status and Meanings of Each LED (Power Supply Unit) ............................................................................27
Table 3.1 General Status of ETERNUS Web GUI.........................................................................................................41
Table 3.2 General Status of ETERNUS CLI .................................................................................................................41
11
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

Chapter 1
Component Name/LED Name
This chapter provides component names of the ETERNUS DX.
1.1 Controller Enclosures
An operation panel and drives are installed in the front of the controller enclosure. Controllers and power
supply units are installed in the rear.
1.1.1 Front
This section provides the names of the components in the front of a controller enclosure.
■2.5" Type
Figure 1.1 Front View of a 2.5" Type Controller Enclosure
1
3 3
2
1. Operation panel
2. 2.5" drive
3. Flange cover
12
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

■3.5" Type
Figure 1.2 Front View of a 3.5" Type Controller Enclosure
1
3 3
2
1. Operation panel
2. 3.5" drive
3. Flange cover
1.1.2 Rear
This section provides the names of the components in the rear of a controller enclosure.
■When Only One Controller is Installed
Figure 1.3 Rear View of a Controller Enclosure (When Only One Controller is Installed)
12
34
1. Controller (CM#0)
2. Cover
Remove this when installing an additional controller (optional).
3. Power supply unit (PSU#0)
4. Power supply unit (PSU#1)
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
13
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

■When Two Controllers are Installed
Figure 1.4 Rear View of a Controller Enclosure (When Two Controllers are Installed)
12
34
1. Controller (CM#0)
2. Controller (CM#1)
3. Power supply unit (PSU#0)
4. Power supply unit (PSU#1)
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
14
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

1.1.3 Components (Front)
This section describes the operation panel and the drives in the front of the controller enclosure.
■Operation Panel
An operation panel has LEDs, a Power switch, and a FUNCTION button.
Figure 1.5 shows the operation panel. Table 1.1 shows the status and meanings of each LED.
Figure 1.5 Operation Panel (Controller Enclosure)
2
3
1
4
56
7
2
3
1
4
56
78
AB
A. With a flange cover
B. Without a flange cover
1. Power switch
This switch is used to turn on or off the ETERNUS DX.
2. POWER LED
3. IDENTIFY LED
4. FAULT LED
5. MAINTENANCE LED
6. CACHE LED
7. READY LED
8. FUNCTION button
This button is used to switch the maintenance status, to switch the master CM (when two controllers are
mounted), or to initialize the LAN ports.
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.1 Status and Meanings of Each LED (Operation Panel (Controller Enclosure))
LED name LED status Meaning
POWER
(green)
DC power is supplied to the controller enclosure.
IDENTIFY (blinks blue) The installation location of the controller enclosure is identified
according to the instruction that is issued from ETERNUS Web GUI
or ETERNUS CLI.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
15
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

LED name LED status Meaning
FAULT (amber) The ETERNUS DX is in error status.
(blinks amber)
A part of the ETERNUS DX requires preventive maintenance.
MAINTENANCE
(green)
Maintenance for the ETERNUS DX is in progress.
(blinks green)
Maintenance (from ETERNUS Web GUI or ETERNUS CLI) is being
performed or a status check of the ETERNUS DX is necessary.
CACHE (green) There is data in the cache memory of the ETERNUS DX.
READY
(green)
The ETERNUS DX is available for use.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
16
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

■Drives
●2.5" Drives
Figure 1.6 shows the 2.5" drive. Figure 1.7 shows the slot number of each 2.5" drive.
Table 1.2 shows the status and meanings of each LED.
Figure 1.6 2.5" Drives
12
1. DRIVE READY LED
2. DRIVE FAULT LED
Figure 1.7 Drive Slot Numbers (2.5" Type Controller Enclosure)
Slot#8 Slot#9
Slot#10 Slot#11 Slot#12 Slot#13 Slot#14 Slot#15
Slot#0 Slot#1 Slot#2 Slot#3 Slot#4 Slot#5 Slot#6 Slot#7
Slot#16 Slot#17 Slot#18 Slot#19 Slot#20 Slot#21 Slot#22 Slot#23
●3.5" Drives
Figure 1.8 shows the 3.5" drive. Figure 1.9 shows the slot number of each 3.5" drive.
Table 1.2 shows the status and meanings of each LED.
Figure 1.8 3.5" Drives
1
2
1. DRIVE READY LED
2. DRIVE FAULT LED
Figure 1.9 Drive Slot Numbers (3.5" Type Controller Enclosure)
Slot#0
Slot#4
Slot#8
Slot#1
Slot#5
Slot#9
Slot#2
Slot#6
Slot#10
Slot#3
Slot#7
Slot#11
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
17
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.2 Status and Meanings of Each LED (Drive (Controller Enclosure))
LED name LED status Meaning
DRIVE READY (green) The drive is in normal status.
(blinks green)
DRIVE FAULT (amber)
•The drive is in error status.
•In response to commands from ETERNUS CLI, the location of
the drive is identified.
1.1.4 Components (Rear)
This section describes the controllers and the power supply units in the rear of the controller enclosure.
■Controllers
The controller contains a CPU, cache memory, System Capacitor Unit (SCU), host interfaces, drive interface
(DI) ports, and LAN ports. The controller controls all operations in the ETERNUS DX.
Controllers (FC, iSCSI, and SAS) are available for different types of host interfaces.
Figure 1.10 shows the controller. Table 1.3 shows the status and meanings of each LED.
Figure 1.10 Controllers
1234 5
1412 13
15
14
15
16 20 21
SAS
FC iSCSI
6810711
9
17 17 17 17
1818
1919
1. PWC port
This port is used to connect a power synchronization unit with an RS232C cable.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
18
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

2. DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a mini SAS HD cable between
enclosures.
When the controller enclosure is a 2.5" type, this port is not used.
3. LAN (RMT) port
These are the RJ-45 connectors to connect LAN cables.
4. LAN (MNT) port
These are the RJ-45 connectors to connect LAN cables.
5. Host interface (CA#0)
This interface is used for connecting a controller with a server.
6. Host interface port (FC port) (CA#0, Port#0)
These are the Dual LC connectors to connect FC cables.
7. Host interface port (FC port) (CA#0, Port#1)
These are the Dual LC connectors to connect FC cables.
8. Host interface port (iSCSI port) (CA#0, Port#0)
These are the RJ-45 connectors to connect LAN cables.
9. Host interface port (iSCSI port) (CA#0, Port#1)
These are the RJ-45 connectors to connect LAN cables.
10. Host interface port (SAS port) (CA#0, Port#0)
These are the miniSAS (SFF-8088) connectors to connect miniSAS cables.
11. Host interface port (SAS port) (CA#0, Port#1)
These are the miniSAS (SFF-8088) connectors to connect miniSAS cables.
12. IDENTIFY/SCU READY LED
13. DI (OUT) LINK/FAULT LED
14. LAN ACT LED
15. LAN LINK LED
16. READY/FAULT LED
17. LINK/FAULT LED
18. FAULT LED
19. LINK LED
20. CA#0 FAULT LED
21. MASTER LED
The LEDs turn on or blink to indicate the statuses that are listed below.
Table 1.3 Status and Meanings of Each LED (Controller)
LED name LED status Meaning
IDENTIFY/SCU READY
(blinks blue)
As ordered via ETERNUS Web GUI or ETERNUS CLI, the installation
location of the controller is identified.
(blinks green)
System Capacitor Unit (SCU) is charging.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
19
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0

LED name LED status Meaning
DI (OUT) LINK/FAULT (green) The link between the DI (OUT) port and the destination port has
been established.
(amber) The link between the DI (OUT) port and the destination port is in
error status.
(blinks amber)
The ports to connect the cables are indicated. This occurs while a
drive enclosure is being added.
LAN ACT
(blinks green)
Data is being sent or received via the LAN port.
LAN LINK (green) The link between the LAN port and the destination has been es-
tablished.
READY/FAULT (green) The controller is in normal status.
(blinks green)
An error has occurred during startup.
(amber)
•The controller is performing the initial setup after the power is
turned on.
•The controller is in error status.
(blinks amber)
LINK/FAULT (green) The link between the host interface port (FC or SAS) and the des-
tination port has been established.
(amber) The host interface port (FC or SAS) is in error status.
FAULT (green) The link between the host interface port (iSCSI) and the destina-
tion port has been established.
LINK (amber) The host interface port (iSCSI) is in error status.
CA FAULT (amber) The host interface is in error status.
MASTER (green) The controller is set as a Master CM.
Chapter 1 Component Name/LED Name
1.1 Controller Enclosures
20
FUJITSU Storage ETERNUS DX60 S3 Disk storage system Operation Guide (Basic)
Copyright 2014 FUJITSU LIMITED
P3AM-9012-01ENZ0