Fujitsu SDLT 160 GBYTE User manual

SDLT 160/320 GBYTE
BETRIEBSANLEITUNG
OPERATING MANUAL
Deutsch
English
Ausgabe Juni 2003
June 2003 edition

Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft
Corporation.
Die übrigen im Buch erwähnten Software- und Hardwarebezeichnungen sind in den meisten
Fällen auch eingetragene Warenzeichen und unterliegen als solche gesetzlichen
Bestimmungen.
Copyright 2003
Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des
Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren.
Zuwiderhandlungen verpflichten zu Schadenersatz.
Alle Rechte vorbehalten, insbesondere für den Fall der Patenterteilung oder GM-Eintragung.
Liefermöglichkeiten und technische Änderungen vorbehalten.
Dieses Handbuch wurde erstellt von
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation.
Other software and hardware names referred to in the manual are generally also registered
trademarks whose use is also subject to legal conditions.
Copyright 2003
All rights, including rights of translation, reproduction by printing, copying or similar methods,
even of parts are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved.
Delivery subject to availability. Right of technical modification reserved.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de

A26361-H814-Z100-1-7419 English
Contents
Introduction........................................................................................................................................1
Notational conventions ..............................................................................................................1
Important notes..................................................................................................................................2
Safety........................................................................................................................................2
Manufacturer's note...................................................................................................................2
Notes on working with magnetic tape cartridges........................................................................2
Cleaning notes...........................................................................................................................3
Installing the streamer.......................................................................................................................4
Setting jumpers..........................................................................................................................4
Installing the streamer ...............................................................................................................6
Connecting the streamer............................................................................................................6
Operation...........................................................................................................................................7
Meaning of the indicators...........................................................................................................7
Switching the drive on................................................................................................................7
Loading a cartridge....................................................................................................................8
Unloading a cartridge.................................................................................................................8
Recommended magnetic tape cartridges...................................................................................8
Technical data...................................................................................................................................9

A26361-H814-Z100-1-7419 English - 1
Introduction
The streamer SDLT 160/320 GBYTE is a drive for magnetic tape cartridges with a storage capacity
of 160 Gbyte (without compression) or 320 Gbyte (with 2:1 compression).
Thanks to its performance capability (high capacity and rapid data transmission) the streamer is
ideally suited for data backup of network systems.
The streamer has a configurable SCSI interface and supports the following SCSI interface types:
•LVD (Low Voltage Differential)
•SE (Single Ended)
In order to operate the streamer, the computer must therefore have a SCSI host adapter and the
appropriate SCSI drivers must be installed.
This brief operating manual provides you with an overview of how to operate the streamer.
To install the drive, you need some knowledge of hardware. Make sure you observe the instructions
in the "Important notes" chapter of your computer's operating manual.
i
In the event of any problems occurring, please contact your sales outlet or our customer
service center.
Further information
For details of the drive mounting procedure refer to the Operating Manual for the computer.
Information on the SCSI interface is contained in the documentation of the SCSI host adapter.
For information on the required SCSI drivers and the backup software, refer to the software
documentation.
Additional information on the streamer SDLT 160/320 GBYTE is also provided in the manual "SDLT
Product Manual" on the Internet (http://manuals.fujitsu-siemens.com).
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
!Pay particular attention to texts marked with this symbol. Failure to observe
this warning endangers your life, destroys the system, or may lead to loss of
data.
i
Supplementary information, remarks, and tips follow this symbol.
ÊText which follows this symbol describes activities that must be performed in
the order shown.
"Quotation marks" indicate names of chapters, disks, and terms that are being emphasized.

SDLT 160/320 GBYTE
2 - English A26361-H814-Z100-1-7419
Important notes
!In this chapter you will find information regarding safety which is essential to take note of
with your drive.
Safety
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our customer service center.
•This device has been developed for use in approved systems with a fire-proof casing (in
accordance with IEC 950 / EN 60950).
Please observe the notes on power loss and environmental conditions in the "Important notes"
chapter of the computer's operating manual.
•Please observe the safety information provided in the "Important notes" chapter in the
computer’s operating manual.
Manufacturer's note
CE certificate
The shipped version of this drive complies with the requirements of the EC Guideline
89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical system configuration.
When installing the drive, observe the specific installation notes in the Operating
Manual or Technical Manual for the receiving device.
Notes on working with magnetic tape cartridges
i
Magnetic tape cartridges and cleaning cartridges for the streamer can be ordered directly
from:
IT Distribution Shop (formerly Siemens Plus Shop)
Telephone: 01805 / 252 723, Fax: 01805 / 252 724
http://www.spls.de/en/index.cfm
Additional information is contained in the manual "SDLT Product Manual".

SDLT 160/320 GBYTE
A26361-H814-Z100-1-7419 English - 3
Although magnetic tape cartridges do not require any special maintenance, some basic rules should
be followed:
!General
•The cartridges are not to be placed near magnetic fields.
•Avoid subjecting the magnetic tape cartridges to high temperatures or direct sunlight.
•Never touch the magnetic tape.
•Never drop the magnetic tape cartridges.
Check the magnetic tape according to the "SDLT Product Manual".
Also observe the notes in the "SDLT Product Manual".
When operating
•The cartridges are not to be operated in high-humidity and in dusty environments.
•Do not remove the magnetic tape cartridge from the drive while it is being read or
written.
•Do not switch off the system while a magnetic tape cartridge is being read or written.
Storage
•The cartridges are not to be stored in high-humidity and in dusty environments.
•Store the magnetic tape cartridges in an upright position, if possible.
Write protection
The magnetic tape cartridges have a slide switch which can be used to activate and deactivate write
protection.
Write protection is activated when the switch is moved to the left (arrow pointing down) and the
orange surface is visible.
Detailed information on the slide switch can be found in any cartridge box.
Cleaning notes
•If the yellow "Cleaning Required" indicator is illuminated, the read/write head on the drive must
be cleaned. Use the cleaning tape provided for this purpose.
•Remove the cleaning tape from the drive once cleaning has been completed.
•Do not use DLT cleaning cartridge for an SDLT drive.
•The cleaning cartridge can be used up to 20 times.
•Observe the notes in the "SDLT Product Manual".

SDLT 160/320 GBYTE
4 - English A26361-H814-Z100-1-7419
Installing the streamer
!Please note the information provided in the operating manual of the computer or in the
"Safety and Ergonomics" booklet.
The following steps must be performed to install the streamer:
•Setting jumpers
•Mounting the streamer
•Connecting the streamer
i
The drivers required for operating SCSI drives are either part of the operating system or
are provided with the software.
Setting jumpers
The drive can be set by means of jumpers. The jumpers can be found on the rear of the drive.
Pin 1
12
3
4
5
1 = Connection for diagnostic purposes
2 = Plug-in jumper for Wide SCSI
configuration
3 = Plug-in jumper for Termination Power
4 = Plug-in jumper for SCSI address
5 = Connection for RS-422 (loader)
Pin 1 is drawn bold in each case.
Connection for diagnostic purposes
This connection is only for internal use.
Wide SCSI configuration
With this plug-in jumper you can configure the streamer for Wide SCSI.
Pin pair 1/2 inserted = 8-bit SCSI
Pin pair 1/2 not inserted = 16-bit SCSI (Wide SCSI)

SDLT 160/320 GBYTE
A26361-H814-Z100-1-7419 English - 5
Default setting:
Pin pair 1/2 not inserted = Wide SCSI
Termination Power
The Termination Power jumper sets the power supply for the terminating resistors on the SCSI bus.
The terminating resistors can be provided with power by the streamer or the SCSI bus.
Pin pair 1/2 inserted = power supply from the streamer
Pin pair 1/2 not inserted = power supply from SCSI bus
Default setting:
Pin pair 1/2 not inserted = power supply from SCSI bus
SCSI address
Every device on the SCSI bus must have its own SCSI address (ID). The SCSI address for the
streamer is set using the pin pairs 1/2 to 7/8.
The streamer is set to the SCSI address 6 in the default setting (jumpers on pin pair 3/4 and pin pair
5/6 inserted). If pin pair 9/10 is inserted, the firmware setting will be bypassed and the value from
the jumper setting will be used.
i
SCSI address 7 is always reserved for the SCSI controller.
SCSI address Pin pair 9/10 Pin pair 7/8 Pin pair 5/6 Pin pair 3/4 Pin pair 1/2
0+––––
1+–––+
2+––+–
3+––++
4+–+––
5–––––
6+–++–
7+–+++
8++–––
9++––+
10 + + – + –
11 + + – + +
12+++––
13+++–+
14++++–
15+++++
+ = installed
– = not installed

SDLT 160/320 GBYTE
6 - English A26361-H814-Z100-1-7419
Connection for RS-422 (loader)
The connector is not in use.
Termination/terminating resistor
The required bus connection is always located on the end of the cable. The drive has no terminating
resistors of its own.
Installing the streamer
The streamer requires a 5 ¼" mounting location of full height. It can be installed horizontally or
vertically.
!When mounting the streamer, ensure that the ventilation slits on the streamer are kept
free.
ÊInstall the streamer as described in the Operating Manual or Technical Manual for the
computer.
Connecting the streamer
The ports can be found on the rear of the streamer.
12
ÊPlug the power supply cable (4-pin) into the power supply socket of the streamer (1).
ÊPlug the Wide SCSI cable (68-pin) into the Wide SCSI interface of the streamer (2).

SDLT 160/320 GBYTE
A26361-H814-Z100-1-7419 English - 7
Operation
13
4
5
2
1 = "Drive Density" indicator
2 = "Drive Status" indicator
3 = "Cleaning required" indicator
4 = Eject button
5 = Infrared interface (Global Storage Link) for
test and diagnostic purposes
Meaning of the indicators
Name Color State Meaning
on Cartridge is formatted for 220 Gbytes.Cartridge type amber
off Cartridge is formatted for 320 Gbytes.
on The drive is ready for use. Probably no
cartridge is inserted.
Drive state green
flashing Drive (tape) is operating.
on Drive head needs cleaning, or the cartridge is
bad.
Cleaning yellow
off Cleaning is complete, or cleaning is
unnecessary.
Switching the drive on
ÊSwitch the computer on.
The streamer performs the power-on self test (POST). If the self test has been successfully
completed, the green indicator lights up.
If the self test is not successfully completed, check the following points:
•Make sure that no cartridge is inserted.
•Make sure that the drive is connected properly.

SDLT 160/320 GBYTE
8 - English A26361-H814-Z100-1-7419
Loading a cartridge
Insert the cartridge (1), and slide it in until it is
fully inserted.
The amber-colored "Drive Density" indicator (2)
lights up when a 220 Gbyte cartridge is detected.
The green "Drive Status" indicator (3) flashes as
long as the cartridge is loaded.
When the tape is at the "Beginning of tape"
(BOT) marker, the green indicator "Drive Status"
remains illuminated.
Unloading a cartridge
Press the Eject button (1) (or issue the
appropriate software command).
The green "Drive Status" indicator (2) flashes as
the tape rewinds.
Wait until the green "Drive Status" indicator (3)
stops flashing and stays on.
ÊRemove the cartridge from the drive (4).
Recommended magnetic tape cartridges
Format Cartridge type Capacity* Maximum data
transfer rate* SDLT320 compatibility
SDLT 320 SDLT I 160 Gbyte 16 Mbyte/s Write/Read
SDLT 220 SDLT I 110 Gbyte 11 Mbyte/s Write/Read
DLT 8000 DLT IV 40 Gbyte 6 Mbyte/s Read only
DLT 7000 DLT IV 35 Gbyte 3.5 Mbyte/s Read only
DLT 4000 DLT IV 20 Gbyte 1.5 Mbyte/s Read only
* Without data compression

SDLT 160/320 GBYTE
A26361-H814-Z100-1-7419 English - 9
Technical data
i
If the following values are different from those in the "SDLT Product Manual", observe the
values listed here.
Dimensions and weight
Height:
•Casing
with cover
Width:
•Casing
with cover
Length:
•Casing
with cover
Weight:
82.55 mm
86.36
146.05 mm
148.34 mm
203.20
212.09 mm
2380 g
Electrical data
Voltage:
Current (typical values)
•+5 V
•+12 V
Ripple
•+5 V
•+12 V
Power consumption:
+5V ±5%
+ 12V ±5%
3.0 A
0.7 A
< 100 mVpp
< 100 mVpp
23 W typical when motor turned on and tape
cartridge inserted
Environmental conditions of the system unit
Environment class 3K2/2K2, IEC 721
Temperature
•When operating
•during transport
Condensation during operation must be
avoided.
15 °C .... 35 °C
-25 °C .... 60 °C
Performance
Data transfer rate:
Cache memory:
16.0 Gbyte/s (without compression)
32.0 Gbyte/s (with 2:1 compression)
40.0 Gbyte/s (Burst)
8.0 Mbyte
Data interface: SCSI MSE (LVD/SE) or HVD, 8-bit single-ended or
differential

SDLT 160/320 GBYTE
10 - English A26361-H814-Z100-1-7419
Regulations complied with: CE (EN60950, EN55022)
UL 1950
CSA C22.2 No. 950
FCC Part 15, Class B
Manufacturer's designation: Super DLT320
System inquiry: Quantum SDLT320
Tape Alert support: yes
Conditions for storing cartridges
Short-term storage
•Temperature
•Humidity
Long-term storage (archiving)
•Temperature
•Humidity
-5 °C .... -45 °C
20% ... 80%
20 °C ±5 °C
50% ±20%
i
To prevent the cartridge tapes from sticking, we advise you to rewind the cartridges once
a year.

Information on this document
On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu-
ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So-
lutions.
This document from the document archive refers to a product version which
was released a considerable time ago or which is no longer marketed.
Please note that all company references and copyrights in this document have
been legally transferred to Fujitsu Technology Solutions.
Contact and support addresses will now be offered by Fujitsu Technology So-
lutions and have the format …@ts.fujitsu.com.
The Internet pages of Fujitsu Technology Solutions are available at
http://ts.fujitsu.com/...
and the user documentation at http://manuals.ts.fujitsu.com.
Copyright Fujitsu Technology Solutions, 2009
Hinweise zum vorliegenden Dokument
Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von
Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seit-
dem den Namen Fujitsu Technology Solutions.
Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine
bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche
Produktversion.
Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden
Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.
Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions
angeboten und haben die Form …@ts.fujitsu.com.
Die Internetseiten von Fujitsu Technology Solutions finden Sie unter
http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die
Benutzerdokumentation.
Copyright Fujitsu Technology Solutions, 2009