Full Spectrum Laser MUSE TITAN User manual

1
Fire Warning 3
Introduction 5
Section I. Safety 6
Setup Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section II. Unboxing Your Muse Titan 11
Unboxing Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section III. Installation & Assembly 15
Remove Protective Foam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Locate & Remove Zip Ties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connect the Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preparing Water Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connect the Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connect the Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Pass-through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Section IV. Touchscreen Interface 23
Touchscreen Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Machine Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Speed Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Section V. Internet Connection 27
Connect to the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Connect to Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Section VI. Tests & Adjustments 30
Alignment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Mirror Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Section VII. Autofocus 39
Autofocusing Your Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting Stall Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table of Contents

Section VIII. Operations 42
Creating a Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Mouse Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Section IX. RetinaEngrave V3 45
Starting on RE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Compound Shapes & Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Passes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Stopping Your Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Section X. Camera 52
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Camera Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Vector Tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Camera Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Section XI. Maintenance 58
Removing the Laser Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Setting Up New Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Belt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Focus Lens Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Air Assist Cone Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Limit Sensor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Section X. Add-ons 68
Water Rerouting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Water Chiller SetUp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Fume Extractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Section Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Warranty 74
Customer Support 76
2
Table of Contents

Laser cutting and engraving systems can present a significant fire hazard due to the extremely
high temperatures generated when the laser beam is in use.
Some material are extremely flammable, catching fire quite easily and damaging the machine and
its surroundings.
Vector Cutting has been proven to have the most potential for igniting material, however fires can be started
when performing Raster Engraving if negligent.
Please read the following warnings and recommendations before using your machine. These instructions should
be followed closely at all times.
●Always keep a properly maintained and inspected 5lbs. or larger fire extinguisher on hand. We
recommend a Halogen or multipurpose dry chemical fire extinguisher.
●Always keep the area around the machine clean and free of clutter.
●Never store any flammable materials in or near the machine.
●Never stack materials near or in your work area.
●Never operate your machine unattended.
●Always use the air assist, especially while vector cutting.
●Never attempt to run a laser with the lid open.
●Never cut PVC (polyvinyl chloride) under any circumstances!!
●Clean the surrounding area regularly to avoid dust getting into the machine.
3
Fire Warning
Materials
Below is a small list of materials usable with the Muse Titan. We will include a list of hazardous material as well.
Cuts Engraves
Acrylic ✓ ✓
Coated Metals X✓
Paper ✓ ✓
Fabric/Leather ✓ ✓
Glass X✓
Rubber ✓ ✓
Stone X✓
Wood ✓ ✓
Fire Warning

Material DANGER! Issues
PVC (Poly Vinyl Chloride)/Vinyl/
Pleather/Most Artificial Leather
Emits Chlorine gas fumes This material can ruin the optics as well as cause the metal of the
machine to corrode. PVC can also ruin the motor system.
Thick ( >1mm )
Polycarbonate/Lexan
Catches fire Polycarbonate is used in the window of varies laser cutters
because it absorbs infrared radiation. Therefore, it cannot be cut
with laser engravers. Trying to do so will create soot that can ruin
the optics and mess up the machine.
ABS plastic Melts, Emits Cyanide
fumes
ABS tends to melt creating melted deposits in the workspace and
is subsequently a high fire risk. It can also release lethal amounts
of hydrogen cyanide.
HDPE/Milk Bottle Plastic Catches fire and melts HDPE can melt creating melted deposits in the workspace and is
subsequently a high fire risk.
PolyStyrene Foam Catches fire Foam can ignite quickly and spread flames rapidly.
PolyPropylene Foam Catches fire Foam can ignite quickly and spread flames rapidly.
Epoxy Emits fumes Epoxy is a resin made out of carbon. Therefore, a CO2 laser can't
cut it. Attempting to do so will result in toxic fumes.
Fiberglass Emits fumes It is made of glass and epoxy. Do not attempt.(Refer to epoxy)
Coated Carbon Fiber Emits fumes Cannot be cut and will emit toxic fumes.(Refer epoxy)
Any food Toxicity Our machines are not designed to be used with food as they
possess no safe food contact surfaces. There are also risks
involved with debris in the workspace polluting any food placed in
the interior. Do not put food in or around the machine.
Material with Sticky Glue or
Adhensive Backing
Coats lens or cracks lens Items that can normally be cut become uncuttable when the
manufacturer adds a layer of peel-off glue on the bottom to
attach them to surfaces.The glue will vaporize forming a coating
on the lens that will coat, cloud, heat, and potentially crack the
lens. It can't be removed without damaging to the lens, requiring a
lens replacement.
DO NOT CUT MATERIALS THAT HAVE THIS BACKING!
HARMFUL MATERIALS:
WARNING!! TRYING TO CUT THESE ITEMS WILL VOID WARRANTY!!
CUT AT YOUR OWN RISK!
Fire Warning
4

Thank you for purchasing your new Muse Titan. Our high quality products will provide years of service simply by
following proper usage and upkeep. With proper usage and upkeep your machine will be a key part in any design
work.
This user manual will guide you through the safety guidelines and operation of your machine. We recommend that
you familiarize yourself with this manual before using your laser engraver.Remember to be safe and have fun!
For more information and product selection, please visit www.fslaser.com
Introduction
Safety Symbols & Meanings
This icon warns of potential fire hazards and fire risks.
Warning about power surges and electrical risks.
This icon indicates potential eye damage.
Warning about glass or cutting hazards.
This icon warns of potential risks of chemical inhalation.
Important information to keep in mind when running you laser.
5

Setup Precautions
6
Follow all safety protocols and procedures before operating any machinery. It is the responsibility
of the operator to ensure all safety precautions are correctly followed, and that the machine is
properly assembled and in working order.
●Always inspect your machine for damage or breakage before each use.
●Do not operate machinery that is damaged or defective in any way.
●Always have a clean, level, and open work space to unbox and place your laser system.
●Never modify, disassemble, or in any way alter the construction of the laser and never start up a
system that has been modified or disassembled.
●Never leave the laser system unattended during operation.
●Keep your laser system clean.
●Do not disassemble the machine or remove any of its protective covers.
●Always have a first-aid kit designed for the initial treatment of burns and smoke inhalation.
●Never operate the machine with any of the panels removed.
●Never place hands or fingers into moving parts such as cooling fans.
Safety During Operation
The output of the CO2 laser is fully contained in a Class 1 enclosure during normal operation. However, the
output beam of the Alignment Laser (visible red diode laser) is accessible to the operator during normal operation, giving
the total system an overall rating of Class 3R. Class 3R lasers have minimal safety concerns when used properly and
handled with care. No special precautions are necessary to operate the high power laser safely. However we recommend
following these Safety Guidelines:
●Never engrave or cut any material containing PVC or vinyl under any circumstance. Your warranty will be
void if your machine is damaged by corrosion from engraving or cutting PVC or vinyl.
●Never engrave or cut any unknown material.
●Never operate the machine without a properly operating ventilation system.
●Never run a laser with the lid open.
●Never look or stare into the visible red diode laser.
Section I. Safety

The power supply is capable of releasing a current up to 20mA. This power is sent to the discharge
terminals on the laser tube itself. In order to prevent access to bare wiring your laser shipped with
silicone terminal covers. Please notify Full Spectrum Laser support and immediately cease operations
if the covers ever slips and exposes the bare wires.
Compliance Statement:
The standard for laser safety is the American Standard for the Safe Use of Lasers, Z136.12000. Developed by the
American National Standards Institute (ANSI) it is the basis for many federal regulations and Occupational Safety
and Health Administration (OSHA) guidelines for laser and laser system manufacturers. It contains detailed
information concerning the proper installation and use of laser systems. While the ANSI standard is not a law, its
recommendations, including warning signage, training, and the designation of a laser safety officer, may be
mandatory under local regulations. It is the operator's responsibility to ensure that the installation and
operation of the Full Spectrum Desktop Laser System are performed following applicable laws. Copies of ANSI
Standard Z136.12000 are available from:
LASER INSTITUTE OF AMERICA 12424 RESEARCH PARKWAY, SUITE 125 ORLANDO, FL 32826 (407) 3801553.
7
Electrical Safety
Section I. Safety
Note: When performing any replacement procedures, make sure the machine is off for at least an hour.
●Do not open any of the machine’s access panels while the unit is plugged in.
●Never make or break any electrical connections to the system while the unit is turned on.
●Never access any electrical areas with hands or tools unless the unit is disconnected from the power
for at least one hour.
●Never replace the installed 20 amp fuse with one of a higher rating.
●POWER ON/OFF is controlled by the switch at the back of the machine, with (-) being ON and (o)
being OFF.
●In case of a blown fuse always contact Technical Support before replacing anything.

Top View
Honeycomb Trays
Water Reservoir
Pause Button
The following diagrams will help you locate all of the machines components.
Section I. Safety
Lid Handles
Lid
Passthrough Cover
Front View
Touch Screen
Front Right View
Rotary Port
8
Fig. 1
Fig. 2
Fig. 3

Side View
Back View
Power
Supply
Air Inlet
Power On/Off
Passthrough Cover
Exhaust Flange
Ethernet Port
Wi-Fi Adapter
Cooling Vents
Section I. Safety
Water Inlet & Outlet
(For Optional Chiller)
Air Assist &
Exhaust Controls
Water Inlet & Outlet
(For Optional Chiller)
Air Inlet
Exhaust Flange
Cooling Fans
9
Fig. 4
Fig.5

Section Review:
Do’s:
●Remember to make sure your work area is nice an clean.
●Always keep an eye on your machine.
●Always inspect your machine for damage or breakage before each use.
●Keep your laser system clean.
●Always keep a fire extinguisher on hand.
●Always have a first-aid kit designed for the initial treatment of burns and smoke inhalation.
Don’ts:
●Do Not Stack Items On Or Near Your Work Area
●Do Not Leave Your Machine Unattended
●Never Operate The Machine With Any Of The Panels Removed.
●Never Access Any Electrical Areas With Hands Or tools Unless The Unit Is Disconnected
From The Power For At Least One Hour.
●Never place hands or fingers into moving parts such as cooling fans.
●Never operate the machine without a properly operating ventilation system.
Section I. Safety
10

WARNING!!
The Muse Titan v2 is approximately 200 lbs. At least two people are required to lift and unbox the machine.
DO NOT TRY TO LIFT ALONE!!
Unboxing Steps
Follow these instructions for best results:
1. Prepare Work Space: You will need an open, level work space to place your laser cutter. A sturdy table with room
for the machine(66” x 34” x 12”) is recommended. Be sure the table is free of clutter and can support a minimum
of 300lbs (the machine itself weighs 176 lbs).
2. Place Box: Due to weight set the box as close to the work area as possible. Flatten the metal tabs on the bottom
of the crate. There are a total of 16 tabs, 5 on the front and back and 3 on the sides.
3. Carefully remove the Cover.
Section II. Unboxing
11
Fig. 6
Fig. 7
Fig. 8

4. Remove the Foam Packaging from the Top and Sides.
5. Lift the Machine with your lifting buddy and place it into the Work Area.
12
Fig. 9
Fig. 10

Checklist
Your laser should come with the following included parts and accessories:
Never use unapproved ducting in the
exhaust system as it is potentially
flammable.
Never operate your laser without a working
exhaust. Full Spectrum Laser recommends
exhaust systems capable of 500 CFM. Keep in
mind that exhaust systems with high flow rates
may require a particle filter for materials with
significant particulates such as wood.
CAUTION! DANGER!
The following items are also needed to run your machine.
Air Compressor 1 liter of Distilled Water
Exhaust Fan
(Optional)
Scissors (Optional for
Unboxing or Set-up)
13
Honeycomb
(QTY: 3) Funnel Wi-Fi Dongle Ethernet Cable Power Cable
2.0, 2.5, and 3.0
mm Hex Key
M4X8 Flange Bolt
(QTY: 4)
Thermal Paper
(QTY: 5)
Lens Wipes
(QTY: 2) Exhaust Flange
4” Duct Clamp
(QTY: 4)
4” Ducting (10’)
(QTY: 2)

Section II. Unboxing
Section Review:
Do’s:
●Remember to Lift Your Box with a partner.
●Remember to lift with your knees.
●Remember to use the lifting strap when lifting the Titan.
●Check your Titan for any damage prior to use.
●Make sure to check that your machine came with all the items on the checklist.
Don’ts:
●Do Not Lift The Box Alone.
●Do Not Lift The Box Using Your Waist or Arms As it Can Lead to Injury.
●Do Not Use Your Machine if You See Any Damage. Contact Support Immediately.
14

This assembly is a simple process that should take less than half an hour to complete. For simplicity we divided
the assembly into seven easy steps.
1. Remove Protective Foam
2. Locate & Remove Zip Ties
3. Connect the Exhaust System
4. Preparing Water Reservoir
5. Assemble the Air Compressor
6. Connect Electrical Power
7. Passthrough
Or
Section III. Setting Up Your Machine
1. Remove Protective Foam
The Titan comes with protective foam inside to prevent damage during shipping. The foam must be
taken off before using your machine.
The first is located below the tube shelf.
The second is located under the laser tube, which can be access behind the tube shelf.
15
Fig. 11
Fig. 12
Tube shelf
Gantry

The machine was secured during shipping with zip ties to hold the laser head assembly and the x-gantry. Remove zip
ties before operating your laser cutter for the first time.
Fig. 13
1. Locate Zip Ties: Refer to Picture above.
2. Cut and Remove Zip Ties: Using a small pair of scissors or wire snips remove all eight zip ties.
Note: The colors of the zip ties may vary depending on availability. The pictures above refer to the general
location of the zip ties. Position may vary depending on movement. Failing to remove all zip-ties will prevent
the gantry from moving.
WARNING!! Do not remove anything else!
Section III. Setting Up Your Machine
2. Locate and Remove Zipties
16

3. Connecting the Exhaust System
An exhaust fan is required to be connected and on whenever a job is run on your laser. A properly installed exhaust fan
removes smoke and fumes from the case and exhausts them to the outside of the building or a fume extractor.
1. Install Exhaust Flange: Use the provided flange bolts to install the ducting collar on the rear of the machine
(as shown in Fig. 14).
Fig. 14 Fig. 15
2. Position Ducting: Place your 4” ducting over the Exhaust Port located at the back of the machine and hold.
Secure with 4” ducting clamp. (See Fig. 15)
3. Attach Exhaust Fan (Optional): Secure the free end of the ducting to the exhaust fan. Repeat the ducting
and clamping process in the other side of the exhaust fan and plug in the fan into the bottom power plug
marked “exhaust” on the back of your Muse Titan machine. (see Fig. 16).
Fig. 16
4. Ventilate Outside or to Fume Extractor: Set the open end outside of a window or to a fume extractor.
Check your system for leaks and be aware that the protective housing is not designed to be airtight; the front
grill is designed to allow an exhaust system to draw fresh air though the work area.
5. Connect to Power: Plug the power cord from the exhaust fan power into the plug marked “exhaust
fan” on the back of your Muse Titan.
Note: Accessories plugged into the back of your Titan will only turn on when the laser is fired (as intended).
FROM MUSE
TO OUTSIDE VENTILATION/
FUME EXTRACTOR
Section III. Setting Up Your Machine
17

The Titan V2 comes with an integrated water cooling system found at the bottom of the right control
panel.( Refer to picture below) The water reservoir must be filled with 1 liter (.26 gallon) of distilled water
using the funnel provided.
Note: The water reservoir must be filled before using the machine. Failure to do so may
cause damage. Failure to put distilled water into the reservoir can lead also cause
damage and may void the warranty.
The water reservoir has a max capacity of 1.75L (.46 gallon). Do not fill more than that.
The water reservoir is equipped with a sensor that will notify you when the water level is low.
Fig. 17
Never Fire the Laser without a correctly connected and powered
water chiller. Firing the laser without turning the pump on or with no
water in the system will severely degrade or destroy your laser tube and
void your warranty.
CAUTION!
Section III. Setting Up Your Machine
4. Preparing Water Reservoir
18
Reservoir Cap

3. Connect to Power: Plug the air compressor power cord into the outlet marked “Air Assist” on the back
of your Muse Titan.
Your air compressor is now ready for use.
Air is used as a pressurized gas to assist in cutting and engraving operations. This pressurized air is critical to safe and
efficient cutting operations as it not only helps cut through material more quickly, but also helps prevent the formation
of flames.
1. Tubeing: Remove the air compressor from its packaging and attach the silicone tube on the air compressor.
2. Attach Air Hose to Laser Cutter: Insert the other end of the hose into the “air inlet” nozzle in the back
of the laser cutter through the barbed air connect.
Fig. 18
Fig. 19
Section III. Setting Up Your Machine
5. Air Compressor Assembly
19