Furniture of America Alvin CM-DK5241 User manual

VERSION # 20-02-14

Thank you for your purchase!
We hope you enjoy this new addition to your home for many years to come.
Our commitment to providing quality products does not simply end when you purchase
our product. We fully stand behind our products from start to finish. Our customer
service department is available Monday – Friday 8:30 AM – 5:30 PM Pacific and can
help with assembly questions as well as, if necessary, replacing damaged or missing
parts. To help expedite our service, please have these assembly instructions readily
available, along with your order receipt.
E-MAIL
[e-mail]
Furniture of America
WEBSITE
www.foagroup.com
FOA Intro
FurnitureOfAmerica
foagroup
Monday to Friday
8:30AM- 5:30PM (PST)
Consumer Hotline
Toll-Free 1-888-980-5122
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessories listed on Page 6 are
accounted for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING
2 / 12

PRE ASSEMBLY
INTRODUCTION
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.
3 / 12

4 / 12

Note :
Every cam lock bolt must have a cam
lock connector in order to fasten the
parts together.
CAM LOCK FASTENER
ASSEMBLY
INSTRUCTIONS
cam bolt cam lock screwdriver
4
Turn the cam lock clockwise gently
until it will not turn any more.
2
Insert the cam bolt into the
bolt hole of joint panel.
3
Align the cam lock with its side opening
(or arrow) pointing to cam bolt.
1
Screw the cam
bolt into panel.
5 / 12

6 / 12

7 / 12

8 / 12
Insert dowels (#C) to top (#1). Attach front
panels (#7) to the dowels (#C) of the top (#1).
Attach cam bolts (#A) to the top
(#1).
Apply dabs of glue (#J) to the
ends of the dowels (#C)
before inserting dowels (#C)
to panels.
1) Align middle panel (#6) to the cam bolts of
the top, then secure by using cam locks (#B).
2) Insert dowels (#C) to front panel, then
align bottom (#5) to the unit. Secure by using
screws (#F).

9 / 12
Insert dowels (#C) to the following panels below.
Align back panel (#4) to the unit, then secure by
using screws (#F).

10 / 12
Align left and right panels (#2,3) to the unit,
then secure by using screws (#F).

11 / 12
Align frames (#8,9,10) together, then secure by
using bolts (#H).
Align frames to the top, then secure by using bolts
(#G) and screws (#F). Attach caps (#I) to the
bottom of the frames.

12 / 12
Align power (#11) to the top, then secure
by using screws (#D).