Furniture of America CM-AC6052 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 15
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-AC6052
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
Rev: 18-10-04

Page 2 of 15
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Page 3 of 15
Cam Lock
Cam Lock Fastener Assembly
Cam Pin
Cam Lock are fasteners used to join two boards
together, usually the edge of one board (A) to the flat
side of another board (B).
Flat side
Board A
Board B
edge to
join
To use Cam Lock
Fasteners:
Step 1 - Insert
cam Pin into the
flat side of a
board. Tighten
only until snug. Do
not over-tighten
Step 2 - Fit the
hole in the
edge of the
joining board
over the Cam
Pin. The head
of the Cam Pin
will be visible in
the large hole
in the side of
the joining
board, as in
Step 3.
Step 3 - Notice the Cam Lock has a "C" -Shaped back. An
arrow on the front points the same direction as the open
section. Insert the Cam Lock into the large hole so the
opening of the "C" fits over the head of the Cam Pin.
arrow head of the Cam Pin
Open section of back
fits over the head os
the Cam Pin
Step 4 - Use a flat screwdriver to turn the Cam Lock
clockwise on half a turn so it locks onto the head of the Cam
Pin. Turn only until it is snug - over-tightening could cause the
Cam to bend or break.
If is will not turn the full amount, turn the Cam Pin out
(counter- clockwese ) one full turn, and try the Cam Lock
again.

Parts List
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 15
#1 x 1pc
Bottom Panel
Upper Panel
#6 x 1pc
#8 x 1pc
Top Panel
#2 x 1pc
Shelf Panel
#3 x 1pc
Top Back Panel
Lower Back Panel
#4 x 1pc
#5 x 1pc
Left Side Panel
Right Side Panel
#7 x 1pc
Hold Set
#A x 2pcs
#C x 6pcs
Bolts
Bolts Ø1/4"x1/2"
#D x 26pcs
#F x 24pcs
#G x 24pcs
#E x 24pcs
#B x 28pcs
Wood Dowels Ø8x30mm
Ø1/4"x1/2"xØ15
Cam Pin
Plastic Cap
Cam Lock
Allen Wrench M4
#H x 1pc

Parts List
Hardware List
Page 5 of 15
#9 x 1pc
Back Panel
Upper Shelf Panel
Lower Shelf Panel
#10 x 1pc
#11 x 1pc Drawer
#13 x 2pcs
#12 x 1pc Left Side Frame
Right Side Frame
#14 x 1pc
Vertical Wine Rack Panels
#15 x 1pc
#16 x 1pc
#8
#11 #7
#1
#2
#3
#4
#5
#6
#9
#10
#12
#13
#14
#15
#16
#I x 2set
Anti-Tip Kit
Horizontal Wine Rack Panel

Page 6 of 15
#A x 2pcs
#C x 6pcs
#C
#H
#4
#A
#D
#2
#D x 2pcs
Secure wine glass holder (#A) to panel
(#4) by using bolts (#C).
Attach dowels (#D) to top back panel (#2).

Page 7 of 15
#D
#3
#D x 2pcs
#2
#4
Attach dowels (#D) to lower back panel (#3).
Align and attach panel (#4) to top back panel (#2).

Page 8 of 15
#D x 6pcs
#F x 6pcs
#F #D
#5
#3
#1
Align and attach shelf panel (#1) to
lower back panel (#3).
Attach dowels (#D) and cam pins (#F) to panel (#5).

Page 9 of 15
#6,7
#F
#D
#D x 6pcs
#F x 6pcs
#F
#D x 4pcs
#F x 4pcs
#8
#D
Attach dowels (#D) and cam pins (#F)
to panels (#6,7).
Attach dowels (#D) and cam
pins (#F) to panel (#8).

Page 10 of 15
#F
#D
#9
#F
#D x 6pcs
#F x 8pcs
#7
#10
#6
#11
#E x 6pcs
#E
#E
FRONT
Attach dowels (#D) and cam pins (#F) to panel (#9).
Align panel (#10) and (#11) to panel (#6), then secure by using
cam locks (#E). Align panel (#7) to panel (#10,11) then secure by
using cam locks (#E). Refer to page 3 on how to secure cam locks
onto cam bolts.