Furniture of America YNJ-1439-1 User manual

YNJ-1439-1
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assemgling a specific product(with 1 being
easy and 5 being difficult). For most
products, two persons are recommended.
EASY DIFFICULT
Page 1 of 9
Tools Required for Assembly:
Allen Wrench
Phillips Screwdriver
(Included)
(Not Included)
2 PERSONS RECOMMENDED
ASSEMBLY INSTRUCTIONS
Rev.14-06-10

Page 2 of 9

Page 3 of 9
PRE
-
ASSEMBLE INTRODUCTION
Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To
help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following
1 Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure y ou have enough space to move around during
the assembly. always have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2 To protect from damage, assemble t he item on a clean, protective surface,
such as on a carpet or cardboard.
3 Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging materi al until assembly is completed.
4 Make sure all parts and hardware are accoun ted by comparing the actual parts
and hardware to the list provided in the asse mbly instructions. Also check for
irregularity such as crack, flaw or improperly drilled hole. If there is any
problem or missing piece, please contact the manufacturer or the supplier. By
having the model number, part number and a brief description of the problem
ready will help expedite the replacement process.
5 Read the entire instructions and view the diagrams first before assembling.
Arrange your parts in order of use and group the identical hardware together
will make it easier to grab each piece as you begin to assemble.
6 During the assembly process, make sure all parts are properly aligned before
tighten with the tool provided or required for the assembly. Do not use power
tools and do not over tighten.
7 When applying glue to the wood dowels to bond the parts together, please be
absolutely certain that the parts are correct and line up with each other
(refer to diagrams and take notice of t he various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.

Page 4 of 9
Door
Door Two screws (C), located at the top and bottom
of the hinge, mount the hinge to the cabinet.
Turn these first to make sure the door is secure.
If the door is still too high or low, loosen these
screws slightly and then lift or lower the door
until it is in the position you want. Firmly tighten
the screws to secure the door. Remember to
support the door as you loosen these screws or
it could drop completely out of its initial position.
Close the cabinet doors to see whether the fit is
satisfactory. Repeat the process if adjustment
is still needed.
The screw closest to the back of the cabinet
(A) is the depth screw and moves the doors in
and out. Use this screw to adjust how far out
or in the doors are in comparison to your
cabinet and to the other cabinet doors and
drawers surrounding it. Loosen the screw
and manually push or pull the door to adjust
it to the position you want. Firmly tighten
the screws to secure the door. Close the
cabinet doors to see whether the fit is
satisfactory. Repeat the process if
adjustment is still needed. If possible,
avoid maxing out the adjusting screw for
it may cause unwanted problems.
The screw closest to the cabinet door (B)
allows the doors to move from side to side.
Tighten this screw (clockwise) to move this
corner of the door further toward the frame;
loosen it (counterclockwise) to move the door
away from the frame. This adjustment can also
be used to correct a door that is not hanging
straight. If the top is further to the left or right
than the bottom, adjust the top and bottom
hinges separately to correct the tilt. Close
the cabinet doors to see whether the fit is
satisfactory. Repeat the process if adjustment
is still needed. If possible, avoid maxing out
the adjusting screw for it may cause
unwanted problems.
Depth Adjustment
Side-to-Side Adjustment
Height Adjustment
Door
HINGE ADJUSTMENT
European-Style Hinge Adjustment

1/5
Page 5of9
HARDWARE LIST
Please keep for future reference
MODEL # YNJ-1439-1
PARTS LIST
CHEST OF DRAWERS
ASSEMBLY INSTRUCTIONS
10PCS 10PCS 20PCS 28PCS 6PCS
6PCS 1PC 1PC
3PCS 6PCS
1 2 345
7 8 9
610
10
ITEM SIZE :47.24" (W) X 15.75" (D) X39.37" (H)
x24PCS
x6PCS
A
B
C
L
M
N
I
H
E
Before you begin,
please read ssembly
and Care Advice?and
re-Assemble
Introduction?
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
1PCS 1PCS 1PCS
1PCS3PCS1PCS
2PCS4PCS1PCS
1PCS2PCS1PCS
1PCS2PCS1PCS
1PCS
47.24"15.75"
39.37"

Page 6of9
STEP : 1
STEP : 2
G
A
C
B
D
2
prepare and inser t wood
dowels into panels 2
2
prepare and screw cam
lock pin into panels
5
4
8
use allen key
to fasten allen-head
wood screw
9
C
D
Hardware 1 = 6pcs
Hardware 2 = 4pcs
Hardware 2 = 6pcs
Hardware 3 = 4pcs
Hardware 4 = 28pcs
Hardware 5 = 6pcs
3
1
ASSEMBLY INSTRUCTIONS
F
G

Page 7of9
STEP : 3
STEP : 4
H
E
H
H
I
I
H
A
B
E
O
P
O
prepare and screw cam
lock pin into panels
1
1
8
use allen key
to fasten allen-head
wood screw
3
10
10
Hardware 1 = 4pcs
Hardware 3 = 10pcs
Hardware 3 = 6pcs
Hardware 10 =6pcs
1
3
X2
ASSEMBLY INSTRUCTIONS

Page 8of9
STEP : 6
STEP : 5
J
6
5
M
M
L
L
N
N
K
Hardware 6 = 3pcs
ASSEMBLY INSTRUCTIONS

Page 9of9
Make sure the item on a flat
surface and it does not feel loose or wobbly.
lf it does double check that the bolts/screws
are secured and proper ly tighten.
ASSEMBLY IS COMPLETED
STEP : 7
ASSEMBLY INSTRUCTIONS
Hardware 7 = 6pcs
7