Furniture of America CM-BK922F User manual

Assembly Instructions
EASY DIFFICULT
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-02-26
CM-BK922F
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
Page 1 of 13

BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
Page 2 of 13

Parts List
#1 x 1pc
#2 x 1pc
#4 x 1pc
#9 x 2pcs
Lower bed rail
#10 x 2pcs
#11 x 1set
#12 x 1pc
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
4 Drawers chest
#3 x 1pc
#5 x 1pc
#7 x 1pc
#6 x 2pcs
#8 x 1pc
#13 x 4pcs
Left side panel
Right side panel
Small rung
Large rung
Support bar
Right headbroad
Left headbroad
Upper bed rail
Slats
Back panel
Guardrail
#16 x 1pc
#15 x 1pc
Extension panel
Extension panel
#14 x 1set
Slats
Page 3 of 13

Hardware List
#I x 4pcs
Bolt Ø5/32"x1"
#J x 4pcs
#K x 20pcs
#L x 16pcs
#C x 12pcs
Bolt Ø1/4"x1-3/16"
#D x 3pcs
#E x 1pc
#F x 8pcs
#M x 16pcs
#N x 16pcs
#G x 8pcs
#H x 8pcs
Allen Wrench M4
Straight Allen Key
Screw Ø1/4"x2-9/16"
Knob
Barrel Nut Ø1/4"
Wood Dowel Ø3/8"x1-9/16"
Rail Bracket Ø1/4"
Screw Ø1/4"x1-3/4"
Screw Ø1/4"x1-3/8"
Screw 5/32"x1-3/16"
Parts List
#17 x 2pcs #18 x 1pc
Center support rail
Support leg
#A x 10pcs
Bolt Ø1/4"x3-1/8"
#B x 6pcs
Bolt Ø1/4"x2-3/8"
#O x 2pcs
#P x 6pcs
#Q x 2pcs
#R x 4pcs
Bracket Plate
Bolt Ø1/4"x1-3/8"
Bolt Ø1/4"x5/8"
Bolt Ø1/4"x1-3/16"
Page 4 of 13

#1
#2
#12
#3
#11
#8
#13
#7
#9
#16
#10
#15
#5
#4
#14
#18
#17
#6
#I x 4pcs
#J x 4pcs
#1
#I
#J
Exploded View
Page 5 of 13
Secure knobs (#J) to the holes of the drawers by using bolts (#I).

#2
#G x 2pcs
#D
#G
#F x 2pcs
#H x 4pcs
#4
#5
#D
#F
#H
#12
#D
#G
#1
#2
#D
Page 6 of 13
Align drawers chest (#1) to the holes of the left side panel (#2), then
secure by using screws (#G).
Align rungs (#4,5) to the lower holes of
the left side panel (#2), then secure by
using screws (#H).
Align back panel (#12) to the upper holes of
the left side panel (#2), then secure by using
screws (#F).

#L x 16pcs
#7
#8
#9
#10
#10
#A x 6pcs
#B x 6pcs
#M x 12pcs
#L #L
#L
#L
#9,#10
#13
x 2
x 4
#M
#D
#B
#A
#M
Page 7 of 13
Attach dowels (#L) to the holes of the side rails (#9,10,13).
Align side rails (#9,10) to the holes of the headboards (#7,8). Insert
bracket (#M) to the holes of the side rails (#9,10). Secure side rails
(#9,10) to headboards (#7,8) by tightening bolts (#A,B) to the
brackets (#M). Do not fully tighten bolts (#A,B).
Use bolts (#B) on this side.
Use bolts (#A) on this side.

#13
#F x 4pcs
#G x 4pcs
#6
#6
#C x 6pcs
#K x 6pcs
#K
#C
#D
#D
#G
#F
Page 8 of 13
Align and attach rails (#13) to the holes of the headboards (#7,8).
{If you are having a tough time fitting rails (#13), then loosen bolts
(#A,B) from steps #5.} Secure rails (#13) by using bolts (#G,F).
Use bolts (#F) on this side.
Use bolts (#G) on this side.
FULLY TIGHTEN ALL BOLTS
ON STEPS #5 and #6.
Align support bars (#6) to the holes of the rails (#13), then
secure by tightening bolts (#C) to nuts (#K).

#A x 4pcs
#M x 4pcs
#9
#15
#16
#K x 8pcs
#O x 2pcs
#P x 6pcs
#Q x 2pcs
#K
#K
#O
#P
#M
#D
#A
#O
#P
#Q
Page 9 of 13
Align lower bed rail (#9) to the holes of the extension panel (#15,16), then insert brackets (#M)
into the lower bed rail (#9). Secure by tightening bolts (#A) onto brackets (#M).
Align extension panels to the bunk bed, then align bracket plates
(#O) to the holes of the extension panels and bunk bed. Secure by
tightening bolts (#P,Q) to nuts (#K).
Use bolts (#P).
Use bolts (#P) and (#Q).

#C x 6pcs
#K x 6pcs
#G x 2pcs
#H x 4pcs
#D
#H
#D
#G
#K
#C
#D
#3
#8
#3
Page 10 of 13
Align right side panel (#3) to the holes of the left headboard (#8),
then secure by tightening bolts (#C) to nuts (#K).
Align stair case to the holes of the right side panel (#3), then secure by using screws (#G,H).
Use screws (#G) here.
Use screws (#H) here.