Furniture of America Vaugh CM-AC680 User manual

The Assembly Rating is a
5-point system showing the
level of effort needed to
assemble a specific product.
ASSEMBLY RATING
EASY DIFFICULT
1 / 7
(Not Included)
Philips
Screwdriver
TOOLS REQUIRED
2 - Persons
Recommended
Furniture of America MODEL #
GIVE US A CALL: 1-888-980-5122
MON – FRI 8:30AM – 5:30PM (PST)
Questions?
CM-AC6801
VERSION # 19-07-25

2 / 7
Thank you for your purchase!
We hope you enjoy this new addition to your home for many years to come.
Our commitment to providing quality products does not simply end when you purchase
our product. We fully stand behind our products from start to finish. Our customer
service department is available Monday – Friday 8:30 AM – 5:30 PM Pacific and can
help with assembly questions as well as, if necessary, replacing damaged or missing
parts. To help expedite our service, please have these assembly instructions readily
available, along with your order receipt.
E-MAIL
[e-mail]
Furniture of America
WEBSITE
www.foagroup.com
FOA Intro
FurnitureOfAmerica
foagroup
Monday to Friday
8:30AM- 5:30PM (PST)
Consumer Hotline
Toll-Free 1-888-980-5122
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessories listed on Page 6 are
accounted for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING

PRE ASSEMBLY
INTRODUCTION
3 / 7
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.

4 / 7

5 / 7
PARTS
HARDWARE
Please keep instructions for
future reference.
Check the quantity and
irregularity of parts and
hardware before you start.
CHAIR
CM-AC6801

6 / 7
1
2
I. Place the backrest (#1) facing down on a protected surface.
II. Align the right armrest (#3) with the pre-drilled holes of the backrest (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer (#C) onto the
bolt (#A) and then the flat washer (#B) onto the SAME bolt (#A), in that
order.
IV. Insert the bolt assemblies through the pre-drilled holes of the backrest (#1)
and secure those bolts using the Allen wrench (#D) to lock them in with the
right armrest (#3).
#3
#1
#D
#A
#C
#B
#D
#A
#C
#B
#D
#A
#C
#B
Part #3 x 1pc
Hardware #A x 3pcs
Part #1 x 1pc
Hardware x 3pcs
Hardware #C x 3pcs
Hardware #D x 1pc
#B
Repeat Step 1 to assemble the left armrest (#4) onto the backrest (#1).
Part #4 x 1pc
Hardware #A x 3pcs
Hardware x 3pcs
Hardware #C x 3pcs
Hardware #D x 1pc
#B
#1
#4
#D #A #C #B
#D #A #C #B
#D #A #C #B
#D
#A
#C
#B

7 / 7
3
4
I. Align the chair seat (#2) with
the pre-drilled holes of the
backrest (#1), the right
armrest (#3) and left armrest
(#4).
II. Prepare 9 bolt assemblies by
inserting FIRST the lock
washer (#C) onto the bolt (#A)
and then the flat washer (#B)
onto the SAME bolt (#A), in
that order.
III. Insert the 6 bolt assemblies
through the inside of the chair
seat (#2)AND 3 bolt
assemblies through the
bottom of the chair seat (#2)
using the Allen wrench (#D) to
lock them in with the backrest
(#1), the right armrest (#3)
and left armrest (#4).
Enlarged
Part #2 x 1pc
Hardware #A x 9pcs
Hardware x 9pcs
Hardware #C x 9pcs
Hardware #D x 1pc
#B
#D
#A
#C
#B
#2
#2
#3
#4
I. Align the legs (#5) with the pre-drilled holes on the bottom of the
chair seat (#2).
II. Insert a screw (#E) through the pre-drilled hole of each leg (#5)
and using the Phillips screwdriver to lock it in with the chair seat
(#2).
#E
#5 #5
#5
#E
Part
Hardware #E x 8pcs
#5 x 4pcs
#E