Furniture of America CM-DK6405 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-DK6405
Phillips Screwdriver
(Not Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-29
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Allen Wrench (Included)

Page 2 of 5

Parts List
#1 x 1 pc
Vanity Table
#2 x 4 pcs
Table Leg
#3 x 1 pc
Mirror
#D x 8 pcs
Screw
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product to
avoid any potential injury and/or damage.
MD
#C x 16 pcs
Flat Washer
#4 x 2 pcs
Mirror Support Rail
Page 3 of 5
#E x 1 pc
Allen Wrench
Hardware List
#5 x 1 pc
Chair Seat
#6 x 4 pcs
Chair Leg
#A x 16 pcs
Bolt 5/16”x2”
#B x 16 pcs
Lock Washer

Page 4 of 5
I. Align the 2 mirror support rails (#4) with the pre-drilled holes on
the back of the mirror (#3).
II. Secure 4 screws (#D) into the 2 mirror support rails (#4) using a
Phillips screwdriver to tighten them to the mirror (#3).
I. With the help of another person,
carefully place the vanity table
(#1) facing down on a protected
surface.
II. Align the 4 table legs (#2) with the
pre-drilled holes on the corners of
the vanity table (#1).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then
the flat washer (#C) onto the
SAME bolt (#A), in that order.
IV. Insert the bolt assemblies through
the pre-drilled holes on the
corners of the vanity table (#1)
and secure those bolts using the
Allen wrench (#E) to lock them
with the table legs (#2).
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
#D x 4 pcs
Turn right (clockwise) to tighten

Page 5 of 5
ASSEMBLY IS COMPLETED
I. Carefully align the 2 mirror support rails (#4) assembled onto the
mirror (#3) with the pre-drilled holes on the back of the vanity
table (#1).
II. Secure 4 screws (#D) into the 2 mirror support rails (#4) using a
Phillips screwdriver to tighten them to the vanity table (#1).
#D x 4 pcs
I. Carefully place the chair seat (#5)
facing down on a protected
surface.
II. Align the 4 chair legs (#6) with the
pre-drilled holes on the corners of
the chair seat (#5).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#A) and then the
flat washer (#C) onto the SAME
bolt (#A), in that order.
IV. Insert the bolt assemblies through
the pre-drilled holes on the corners
of the seat (#5) and secure those
bolts using the Allen wrench (#E) to
lock them with the chair legs (#6).
V. Make sure the vanity table and the
chair are rested on a flat surface
and do not feel loose or wobbly. If
they do, double check that the
bolts/screws are secured and
properly tightened.
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten