Furniture of America CM3311PC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-26
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3311PC-2PK
Phillips Screwdriver
(Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 1 pc x 2
Right Front Leg
#A x 4 pcs x 2
Bolt 5/16”x3-1/4”
#B x 4 pcs x 2
Bolt 5/16”x2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 1 pc x 2
Bolt 5/16”x1-1/2”
MD
#D x 9 pcs x 2
Lock Washer
Page 3 of 5
#E x 9 pcs x 2
Flat Washer
#F x 1 pc
Allen Wrench
Note: The above parts and hardware are shown
for a complete assembly of ONE chair.
However, the actual parts and hardware (with an
exception of the Allen wrench and glue) in the
box will be twice the quantities listed to include
the assembly of the second chair.
#4 x 1 pc x 2
Left Front Leg
#5 x 1 pc x 2
Left Leg Support
#6 x 1 pc x 2
Right Leg Support
#7 x 1 pc x 2
Front Leg Support #G x 6 pcs x 2
Wood Screw
#H x 1 pc
Glue

I. Place the seat (#2) on a protected surface.Apply glue (#H) onto
the ends of the front leg support (#7) and then insert the leg
support (#7) into the right front leg (#3) and the left front leg (#4).
II. Align the front legs (#3 & #4) with the pre-drilled holes on the
corner of the seat (#2).
III. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#B) and then the flat washer (#E) onto the
SAME bolt (#B), in that order.
IV. Insert the bolt assemblies through the corners of the seat (#2)
and secure those bolts using the Allen wrench (#F) to lock them
with the front legs (#3 & #4).
Turn right (clockwise) to tighten
Page 4 of 5
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
I. Apply glue (#H) onto the ends of
the right leg support (#6) and the
left leg support (#5) and then
insert them into the pre-drilled
holes of the backrest with legs
(#1).
II. Align the assembled seat (#2) with
the pre-drilled holes of the
backrest with legs (#1). Insert the
other ends of the right leg support
(#6) and the left leg support (#5)
into the right front leg (#3) and the
left front leg (#4).
III. Prepare a bolt assembly by
inserting FIRST the lock washer
(#D) onto the bolt (#C) and then
the flat washer (#E) onto the
SAME bolt (#C), in that order.
IV. Insert the bolt assembly through
the center hole of the seat (#2)
and secure that bolt using the
Allen wrench (#F) to lock it with
the backrest with legs (#1).
#C x 1 pc
#D x 1 pc
#E x 1 pc
Turn right (clockwise) to tighten
Note: Right and left are
determined by facing the
front of the chair in the
upright position.

I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#A) and then the flat washer (#E) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies through the corners of the seat (#2) and
secure those bolts using the Allen wrench (#F) to lock them with
the backrest with legs (#1).
Page 5 of 5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR
Turn right (clockwise) to tighten
I. Secure all the leg supports with 6 wood screws (#G) using a
Phillips screwdriver to lock them with the backrest with legs (#1),
the right front leg (#3) and the left front leg (#4).
II. Carefully place the completed chair in upright position. Make sure
the chair is rested on a flat surface and does not feel loose or
wobbly. If it does, double check that the bolts/screws are secured
and properly tightened.
#G x 6 pcs
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten