Furniture of America Dickinson CM3187PBN User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3187PBN
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-11-21
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
Phillips Screwdriver
(Not Included)
Wrench
(Not Included)
2 PERSONS RECOMMENDED

Page 2 of 5

Parts List
#1 x 1 pc
Backrest w/Legs
#2 x 1 pc
Seat
#3 x 2 pcs
Front Leg
#D x 11 pcs
Flat Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
#C x 4 pcs
Hex Nut
#4 x 1 pc
Front Leg Support
Page 3 of 5
#E x 11 pcs
Lock Washer
Hardware List
#5 x 2 pcs
Side Leg Support
#A x 4 pcs
Bolt 1/4”x3-1/4”
#B x 3 pcs
Bolt 1/4”x1-1/2”
#G x 6 pcs
Screw M4x38mm
#H x 1 pc
Wrench
#F x 1 pc
Allen Wrench
Due to the size and/or weight of this
product, it is highly recommended
that the assembly should be done
near the area of its intended location.
Make sure you have enough space
to move around during the
assembly. ALWAYS have at least two
people to help with transporting and
assembling the product to avoid any
potential injury and/or damage.

Turn right (clockwise) to tighten
Page 4 of 5
#B x 3 pcs
#D x 3 pcs
#E x 3 pcs
Turn right (clockwise) to tighten
I. Place the backrest with legs (#1) on a protected surface.
II. Align the seat (#2) with the pre-drilled holes of the backrest with
legs (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#B) and then the flat washer (#D) onto the
SAME bolt (#B), in that order.
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#A) and then the flat washer (#D) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies through the pre-drilled holes on the
corners the seat (#2) and secure those bolts using the Allen
wrench (#F) to lock them with the backrest with legs (#1).
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs

I. Insert the front leg support
(#4) between the 2 front legs
(#3). Then insert the 2 side
leg supports (#5) into the
backrest with legs (#1) and
the 2 front legs (#3).
II. Align the 2 front legs (#3)
with the pre-drilled holes of
the seat (#2).
III. Insert FIRST the flat washer
(#D) onto the threaded stud
of the front legs (#3) and then
the lock washer (#E) onto the
SAME stud, in that order.
Secure the hex nut (#C) onto
the same stud using the
wrench (#H) to tighten the
parts together.
Page 5 of 5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR.
Turn right (clockwise) to tighten
I. Secure the front leg support
(#4) and the 2 side leg
supports (#5) with 6 screws
(#G) using a Phillips
screwdriver to lock them with
the backrest with legs (#1)
and the 2 front legs (#3).
II. Carefully turn the completed
bench upright. Make sure the
bench is rested on a flat
surface and does not feel
loose or wobbly. If it does,
double check that the
bolts/screws are secured and
properly tightened.
#G x 6 pcs
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten