Furniture of America CM3824PT-VN User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]
CM3824PT-VN
Rev: 19-01-16

Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 8
#1 x 1pc
#2 x 1pc
Table Top
Left Side Panel
#3 x 1pc
Right Side Panel
#4 x 1pc
Stretcher
#5 x 2pcs
Connection Panel
#6 x 1pc
Drawer
#7 x 1pc
Drawer Wine Rack A
#8 x 1pc
Drawer Wine Rack B
#C x 8pcs
Flat Washer Ø5/16"x19x2
#B x 8pcs
#A x 8pcs
Bolt Ø5/16" x 1-1/4"
Lock Washer Ø5/16"x12x1.5
#D x 16pcs
#E x 16pcs
#F x 8pcs
#G x 8pcs
#H x 1pc
Allen Wrench M5
Flat Washer Ø1/4"x19x2
Lock Washer Ø1/4"x11x1.5
Bolt Ø5/16" x 2"
Bolt Ø1/4" x 7/8"

Page 4 of 8
#J x 4pcs
L Metal Plate
#I x 1pc
Allen Wrench M4
Hardware List
#K x 10pcs
Screw #3.5 x 15mm
#2
#3
#6
#1
#4
#5
#5
#7
#8

Page 5 of 8
#2
#3
#4
#I
#C
#G
#F
#J
#J
#C
#G #F
#I
#J
#2
#3
#4
#C x 4pcs
#Fx 4pcs
#Gx 4pcs
#J x 4pcs
#C x 4pcs
#Fx 4pcs
#Gx 4pcs
Hook stretcher (#4) to the latch of left and
right side panels (#2,3), then align
brackets (#J) to the holes of the stretcher
(#4) and side panels (#2,3). Secure by
using bolts (#C) with washers (#G,F).
Make sure to secure brackets
(#J) on the bottom holes of the
stretchers (#4) and side panels
(#2,3) by using bolts (#C) with
washers (#G,F).
DO NOT FULLY TIGHTEN ALL BOLTS UNTIL THE
FULL ASSEMBLY OF TABLE IS COMPLETED.

Page 6 of 8
#B x 8pcs
#D x 8pcs
#E x 8pcs
#2
#3
#5
#5
#H
#B
#E
#D
#K x 4pcs
#6
#2
#3
#4
#K
Align connection panels (#5) to the side
panels (#2,3), then secure by using
bolts (#B) with washers (#E,D).
Align drawer (#6) to the drawer rails. Make sure that the alignment of
drawer (#6) is correctly centered to the side panels (#2,3), because there
will be no pre-drilled holes. Secure drawers rails to the drawer (#6) by
using screws (#K).

Page 7 of 8
#K x 6pcs
#2
#3
#6
#K
#A x 8pcs
#D x 8pcs
#E x 8pcs
#2
#3
#1
#6
#H
#A
#E
#D
Extend drawer (#6), then secure drawer (#6) to
drawer rails by using screws (#K).
Align connection panels (#5) to the holes
of the table top (#1), then secure by
using bolts (#A) with washers (#E,D).

Page 8 of 8
#6
#8
#7
#1
ASSEMBLY IS COMPLETED
Extend drawer (#6), then place drawer win racks (#7,8) inside drawer (#6).