Furniture of America CM7132F User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 10
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-03-12
CM7132F
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 10
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Page 3 of 10
#1 x 1pc
#2 x 1pc
#3 x 1pc
#4 x 1pc
Upper Back Side Rail
Heardboard (Left)
Heardboard (Right)
#5 x 2pcs
Upper Front Side Rail
Lower Guardrail
#6 x 1set
Full Slat Kit (13pcs)
#7 x 2pcs
Vertical Bar
#8 x 1pc
Frames (Left)
#A x 16pcs
Bolt 1/4" x 4-3/8"
#B x 16pcs
Barrel Nut 1/4" x 1/2"
#C x 18pcs
Bolt 1/4" x 1-3/8"
#D x 16pcs
Bolt 1/4" x 1"
#E x 12pcs
Wood Dowel 7/16" x 1-9/16"
#H x 11pcs
Screw 4 x 30mm
#F x 1pc
Wood Dowel 7/16" x 1-3/16"
#G x 8pcs
Wood Dowel 7/16" x 3/4"
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.

Page 4 of 10
#9 x 1pc
#10 x 1pc
Crossbar
Frames (Right)
#11 x 2pcs
Window
#12 x 4pcs
#13 x 2pcs
Window
Window
#14 x 1pc
Center Support
#I x 1pc
Allen Wrench 4mm
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#11
#12
#12
#13
#13
#14
Parts List Hardware List

#I
#A
#E
#B
#I
#A
X2
#7
#8,#9
#E
#B
#A x 16pcs
#B x 16pcs
#E x 12pcs
#C x 3pcs
#1
#2
#5
#4
#3
Page 5 of 10
#I
#C
1) Insert dowels (#E) and barrel nuts (#B) to the holes
of the upper side rails (#3,4), then align the upper side
rails (#3,4) to the upper holes of the headboards (#1,2).
Secure by tightening bolts (#A) onto the inserted barrel
nuts (#B) in the upper side rails (#1,2).
2) Insert dowels (#E) and barrel nuts
(#B) to the holes of the lower
guardrails (#5), then align the
guardrails (#5) to the holes of the
headboards (#1,2). Secure by
tightening bolts (#A) onto the
inserting barrel nuts (#B) in the
guardrails (#5).
Align vertical bars (#7) to the holes of the frames (#8,9). Secure by
using bolts (#C). The vertical bar (#7) could either be aligned to the
right or left side of the frames (#8,9) depending on the frames.

#I
#C
#8,#9
#I
#C
#I
#D
#G
#C x 10pcs
#D x 4pcs
#G x 2pcs
#9
#8
#11
#11
Page 6 of 10
#9
#8
#2
#3
#1#1
Align frames (#8,9) to the holes of the unit, then secure by using bolts (#C).
Insert dowel (#G) to the window bar (#11), then
align window bar (#11) to the holes of the
window. Secure by using bolts (#D).

#I
#D
#G
#G
#I
#D
#13
#D x 8pcs
#G x 4pcs
#D x 4pcs
#G x 2pcs
#12
#12
#13
#13
Page 7 of 10
#9
#8
#9
#8
Insert dowel (#G) to the window side bars (#12), then align window side bars (#12)
to the holes of the window. Secure by using bolts (#D).
Insert dowel (#G) to the bottom window bars (#13),
then align bottom window bars (#13) to the holes of
the window. Secure by using bolts (#D).

#I
#F
#C
#C x 2pcs
#F x 1pc
#H x 2pcs
#H
#10
#14
#3
#2
#1#1
Page 8 of 10
Insert dowel (#G) to the crossbar (#10), then align crossbar (#10) to the holes of the unit.
Secure by using bolts (#C).
Align center support (#14) to the headboards
(#1,2), then secure by using screws (#H).

#H
#H x 9pcs
#6
ASSEMBLY IS COMPLETED
Page 9 of 10
Align slats (#6) to the upper bunk,
then secure by using screws (#H).

Page 10 of 10