Furniture of America CM7529T User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 19-04-10
CM7529T
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 8
#1 x 1pc
Headboard Leg (Left)
#2 x 1pc
#3 x 1pc
#4 x 1pc
#5 x 1pc
#7 x 1pc
#8 x 2pcs
#6 x 2pcs
Hardware List
#A x 8pcs
#B x 8pcs
#D x 8pcs
#F x 18pcs
Bolt ɸ1/4" x 3-1/8"
#H x 1pc
#C x 8pcs
Barrel Nut ɸ1/4" x 1/2"
Wood Dowel ɸ10 x 40mm
Screw ɸ4 x 30mm
Allen Wrench 4mm
Screw ɸ1/4" x 4"
#E x 8pcs
Hex Cap ɸ1/4" x 5/8"
#G x 8pcs
Bolt ɸ1/4" x 1-3/16"
Headboard Leg (Right)
Footboard Leg (Left)
Horizontal Bar Bed
Horizontal Bar Bed
Footboard Panel
Side Rail
Footboard Leg (Right)

#10 x 2pcs
#9 x 2pcs
Support Leg
#11 x 1set
Page 4 of 8
Twin Slat Kit (10pcs)
Side Rail
#1
#2
#5
#6
#9
#10 #8
#3
#8
#10
#9
#4
#7
#11
Parts List

Page 5 of 8
#C x 6pcs
#F x 12pcs
#H
#C
#F
#1
#2
#5
#6
#3
#4
#5
#H
#C
#C x 2pcs
#F x 4pcs
#F
Attach dowels (#F) on each end of the bar beds (#5,6), then
align bar beds (#5,6) to the headboard legs (#1,2). Secure by
using screws (#C).
#7
Insert dowels (#F) to each ends of the footboard panel (#7),
then align footboard panel (#7) to footboard legs (#3,4).
Secure by using screws (#C).

Page 6 of 8
#A x 4pcs
#B x 4pcs
#H
#8
#9
#B
#A
#10
#10 #E
#D
#H
#D x 4pcs
#E x 4pcs
#8
#9
#1
#2
Align side rails (#8,9) to the headboard (#1,2), then insert barrel
nuts (#B) to the inner side holes of the side rails (#8,9). Secure by
tightening bolts (#A) onto barrel nuts (#B).
Align support legs (#10) to the side rails (#8,9), then
secure by tightening bolts (#D) to hex caps (#E).

Page 7 of 8
#F x 2pcs
#F
#8
#9
#10
#10
#9
#8
#E
#D x 4pcs
#E x 4pcs
#D
#H
#10
#10
#8
#9
#8
#9
Insert dowels (#F) onto side rails (#8,9), then align side rails (#8,9)
to each other as shown in the diagram.
Secure side rails (#8,9) to support legs (#10) by tightening
bolts (#D) onto hex caps (#E).

#G
Page 8 of 8
#B
#A
#A x 4pcs
#B x 4pcs
#H
#G x 8pcs
#8
#9
#7
#8
#9
#8
#9
#11
Align footboard (#7) to the side rails (#8,9), then insert barrel nuts (#B) to
the side holes of the side rails (#8,9). Secure by tightening bolts (#A) onto
barrel nuts (#B).
Align slats (#11) onto side rails, then
secure by using screws (#G).