Furniture of America CM-AC102 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-17
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
CM-AC102
Phillips Screwdriver
Flat-Head Screwdriver
(Not Included)
(Not Included)

Page 2 of 7

Parts List
Hardware List
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7

Page 4 of 7
Turn the cam lock
connector with a
screwdriver until it
will not turn any
more with light to
moderate force.
Align the cam lock connector so that the cam lock bolt can
be inserted.
Secure the threaded end of
the cam lock bolt by using a
flat-head screwdriver.
Align the cam lock
bolt with the pre-
drilled hole.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Turn right (clockwise) to tighten
Step 1 Insert a total of 4 wood dowels (#E) and 6 cam lock bolts (#A-1) onto the
legs (#1-1 & #1-2). Insert 4 cam lock connectors (#A-2) onto the left apron
(#2) and 2 cam lock connectors (#A-2) onto the left leg support (#4). See
diagram below and refer to “CAM LOCK FASTENER ASSEMBLY
INSTRUCTIONS” for connecting those parts together.
#A-1 x 6 pcs
#A-2 x 6 pcs
#E x 4 pcs
Note: Every cam
lock bolt must have
a cam lock
connector in order
to fasten the parts
together.

Step 2 Repeat Step 1 for the assembly of the legs (#1-3 &
#1-4), the right apron (#4) and the right leg support
(#4).
Step 3
Page 5 of 7
#A-1 x 6 pcs
#A-2 x 6 pcs
#E x 4 pcs
#A-1 x 2 pcs
#A-2 x 8 pcs
Insert a total of 2 cam lock bolts (#A-1) and 4 cam lock
connectors (#A-2) onto the front and back leg supports
(#5). Insert 4 cam lock connectors (#A-2) onto the base
(#6). See diagram below and refer to “CAM LOCK
FASTENER ASSEMBLY INSTRUCTIONS” for
connecting those parts together.
1-4

Page 6 of 7
Step 5
Step 4
#A-1 x 5 pcs
#A-2 x 4 pcs
#E x 2 pcs
#2 #1-1
#1-2
#A-1 x 5 pcs
Insert a total of 4 cam lock bolts (#A-1) and 2 wood dowels
(#E) onto the legs (#1-1 & #1-2). Insert 1 cam lock bolt (#A-
1) onto the left leg support (#4)AND 4 cam lock connectors
(#A-2) onto the back apron (#8). See diagram below and
refer to “CAM LOCK FASTENER ASSEMBLY
INSTRUCTIONS” for connecting those parts together.
Insert a total of 4 cam lock bolts (#A-1) onto the legs (#1-3 &
#1-4)AND 1 cam lock bolt (#A-1) onto the right leg support
(#4). See diagram below and refer to “CAM LOCK
FASTENER ASSEMBLY INSTRUCTIONS” for connecting
those parts together.
#4
#4
#1-4
#1-3

Page 7 of 7
Step 7
Step 6
#A-1 x 6 pcs
#A-2 x 6 pcs
#E x 6 pcs
I. Align the drawer front (#9) with the pre-drilled hole in front of the drawer (#10).
II. Secure 4 bolts (#D) by using the Allen wrench (#F) to lock the drawer (#8) with the
drawer front (#9).
III. Align the knob (#C) with the pre-drilled hole on the drawer cover (#9). Insert the bolt
(#B) from the inside of the drawer (#10) and secure that bolt using the Allen wrench
(#F) to lock the drawer (#10) with the knob (#C).
IV. Insert the completed drawer onto the stand.
V. Insert 2 wood dowels (#G) onto the lattice (#9). Then insert the lattice (#9) with the
wood dowel ends onto the two pre-drilled holes of the bottom shelf (#5-1).
VI. Make sure the unit is rested on a flat surface and it does not feel loose or wobbly. If
it does, double check that the connections are secured and properly tighten.
ASSEMBLY IS COMPLETED
#B x 1 pc
#D x 4 pcs
Insert 6 wood dowels (#E) and 6 cam lock bolts (#A-1) onto the top
(#7). Insert a total of 6 cam lock connectors (#A-2) onto the left,
right and back aprons (#2, #3 & #8). See diagram below and refer
to “CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS” for
connecting those parts together.
Turn right (clockwise) to tighten
#C