Furniture of America CM-AC105 User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-AC105
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-21
Page 1 of 6
DIFFICULT
ASSEMBLY RATING

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List Hardware List
#1 x 1 pc
Table Top
#2 x 4 pcs
Leg
#3 x 1 pc
Shelf
#A x 8 pcs
Bolt 1/4”x2”
#B x 16 pcs
Flat Washer
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 16 pcs
Lock Washer
MD
#D x 1 pc
Allen Wrench
Page 4 of 6
#E x 8 pcs
Bolt 1/4”x1/2”
#F x 4 pcs
L-Bracket

Turn right (clockwise) to tighten
Page 5 of 6
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Carefully place the table top (#1)
facing down on a protected
surface.
II. Align the 4 legs (#2) with the pre-
drilled holes on the bottom corners
of the table top (#1).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
IV. Insert the bolt assemblies through
the table top (#1) and secure
those bolts using the Allen wrench
(#D) to lock them with the legs
(#2).
#B x 8 pcs
#C x 8 pcs
#E x 8 pcs
#F x 4 pcs
I. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#E) and then
the flat washer (#B) onto the
SAME bolt (#E), in that order.
II. Align the long side of the L-
brackets (#F) with the pre-drilled
holes on the shelf (#3). Insert 4
bolt assemblies through the long
side of the L-brackets (#F) and
secure those bolts using the Allen
wrench (#D) to lock them with the
shelf (#3).
III. Align the short side of the L-
brackets (#F) assembled on the
shelf (#3) with the pre-drilled
holes on the legs (#2). Insert 4
bolt assemblies through the short
side of the L-brackets (#F) and
secure those bolts using the Allen
wrench (#D) to lock them with the
legs (#2).
Turn right (clockwise) to tighten

Page 6 of 6
ASSEMBLY IS COMPLETED
I. Place drawer into the table top (#1).
II. Make sure the table is rested on a flat surface and does not feel
loose or wobbly. If it does, double check that the bolts/screws
are secured and properly tightened.
#1