Furniture of America CM7999BK-Q User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (#G)
Assembly Instructions
Tools Required for Assembly:
Rev.14-02-24
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM7999BK-Q
(Black)
2 PERSONS RECOMMENDED
CM7999WH-Q
(White)
Wrench (#N)
Phillips Screwdriver
(Not Included)

Page 2 of 6

Page 3 of 6
Image
Parts List Hardware List (Continued)
#1 x 1 pc
Headboard
#2 x 1 pc
Left Headboard Leg
#3 x 1 pc
Right Headboard Leg
#D x 4 pcs
Bolt 5/16”x1-3/16”
Image #4 x 1 pc
Footboard
#5 x 2 pcs
Bed Rail
#E x 4 pcs
Flat Washer 5/16”x5/8”
#F x 4 pcs
Lock Washer 5/16”x1/2”
#G x 1 pc
Allen Wrench
#7 x 4 pcs
Bed Slat Support Leg
#H x 8 pcs
Flat-Head Screw 1/8”x1-3/16”
#I x 8 pcs
Threaded Stud
#6 x 4 pcs
Bed Slat
Hardware List
#A x 2 pcs
Bolt 1/4” x 1-3/8”
#B x 2 pcs
Flat Washer 1/4”x3/4”
#C x 2 pcs
Lock Washer 1/4”x3/8”
#J x 8 pcs
Nylon Washer
#K x 8 pcs
Flat Washer 1/4”x5/8”
#L x 8 pcs
Lock Washer 1/4”x1/2”
#M x 8 pcs
Hex Nut
#O x 4 pcs
Wood Dowel

Before you begin, please read Page
2 of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 6
MD
Turn right (clockwise) to tighten
Step 1 I. Align the headboard (#1) with the right headboard leg (#3).
II. Prepare a bolt assembly by inserting FIRST the spring washer (#C)
onto the bolt (#A) and then the flat washer (#B) onto the SAME bolt
(#A), in that order. Insert the bolt assembly through the TOP hole
of the right headboard leg (#3) and secure that bolt using the Allen
wrench (#G) to lock it with the headboard.
III. Prepare two bolt assemblies by inserting FIRST the spring washer
(#F) onto the bolt (#D) and then the flat washer (#E) onto the
SAME bolt (#D), in that order. Then insert one bolt assembly
through the MIDDLE hole and the other bolt assembly through the
BOTTOM hole of the right headboard leg (#3) and secure the bolts
using the Allen wrench (#G) to lock them with the headboard.
IV. For the assembly of the left headboard leg (#2) onto the
headboard (#1), repeat the process above.
(Back Side)
Note: Right and left headboard leg are determined by standing behind the bed.
#A x 2 pcs
#B x 2 pcs
#C x 2 pcs
#D x 4 pcs
#E x 4 pcs
#F x 4 pcs
Bolt Assembly For Top Hole Only
Bolt Assembly For Top Hole Only
Bolt Assembly For Middle and Bottom Holes Only
Bolt Assembly For Middle and Bottom Holes Only
Enlarged
Enlarged

Page 5 of 6
Step 2
Step 3 In this step you will be securing the bedrails to the headboard legs and the
footboard. Insert the nylon washer (#J), the flat washer (#K)) and then the
lock washer (#L) onto the two threaded studs (#I), in that order through the
openings of the bed rail. Secure the assembly with the hex nut (#M) by
using the wrench (#N) to tighten.
Repeat the process for the remaining 3 locations as shown on the diagram.
#I x 8 pcs
#O x 4 pcs
I. For this step, you will be working with the headboard legs, bed rails and footboard. Please
note that the right and left of headboard legs and rails are determined by standing BEHIND
the bed.
II. Insert the two threaded studs (#I) and one wood dowel (#O) onto the right headboard leg
(#3), the left headboard leg (#2) and on each end of the footboard (#4).
III. For installation of the bed rails(#5) to the headboard legs, take the smaller end of the bed
rail and connect it with the assembled hardware of the headboard leg. Repeat for the other
side.
IV. For installation of the bed rails(#5) to the footboard (#4), take the larger end of the bed rail
and connect it with the assembled hardware of the footboard. Repeat for the other side.
#J x
#K x
#L x
#M x
8 pcs
8 pcs
8 pcs
8 pcs
Turn right (clockwise) to tighten
#5
#5
Enlarged
Enlarged

Page 6 of 6
Turn right (clockwise) to tighten
Step 4
Step 5 Align the assembled bed slat with the pre-drilled holes on each end
of the bed slat (#6) with the pre-drilled holes on each end of bed rails
(#5). Secure two flat-head screws (#H) onto each end of the bed slat
by using a Phillips screwdriver to tighten them down to the bed rails.
Repeat the process for the remaining 3 assembled bed slats.
#7 x 4 pcs
Install the bed slat support leg (#7) onto the bed slat (#6) by aligning
the threaded end of the bed slat support leg (#7) with the center pre-
drilled hole of the bed slat (#6) and turn right (clockwise) by hand until
tighten and secured. properly tighten. Repeat the process for the
remaining three bed slat support leg.
#H x 8 pcs
Turn right (clockwise) to tighten
#7
Enlarged
Enlarged

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (#G)
Assembly Instructions
Tools Required for Assembly:
Rev.14-02-24
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM7999BK-CK
CM7999BK-EK
(Black)
2 PERSONS RECOMMENDED
CM7999WH-CK
CM7999WH-EK
(White)
Wrench (#N)
Phillips Screwdriver
(Not Included)

Page 2 of 6

Page 3 of 6
Image
Parts List Hardware List (Continued)
#1 x 1 pc
Headboard
#2 x 1 pc
Left Headboard Leg
#3 x 1 pc
Right Headboard Leg
#D x 4 pcs
Bolt 5/16”x1-3/16”
Image #4 x 1 pc
Footboard
#5 x 2 pcs
Bed Rail
#E x 4 pcs
Flat Washer 5/16”x5/8”
#F x 4 pcs
Lock Washer 5/16”x1/2”
#G x 1 pc
Allen Wrench
#7 x 8 pcs
Bed Slat Support Leg
#H x 8 pcs
Flat-Head Screw 1/8”x1-3/16”
#I x 8 pcs
Threaded Stud
#6 x 4 pcs
Bed Slat
Hardware List
#A x 2 pcs
Bolt 1/4” x 1-3/8”
#B x 2 pcs
Flat Washer 1/4”x3/4”
#C x 2 pcs
Lock Washer 1/4”x3/8”
#J x 8 pcs
Nylon Washer
#K x 8 pcs
Flat Washer 1/4”x5/8”
#L x 8 pcs
Lock Washer 1/4”x1/2”
#M x 8 pcs
Hex Nut
#O x 4 pcs
Wood Dowel

Before you begin, please read Page
2 of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 6
MD
Turn right (clockwise) to tighten
Step 1 I. Align the headboard (#1) with the right headboard leg (#3).
II. Prepare a bolt assembly by inserting FIRST the spring washer (#C)
onto the bolt (#A) and then the flat washer (#B) onto the SAME bolt
(#A), in that order. Insert the bolt assembly through the TOP hole
of the right headboard leg (#3) and secure that bolt using the Allen
wrench (#G) to lock it with the headboard.
III. Prepare two bolt assemblies by inserting FIRST the spring washer
(#F) onto the bolt (#D) and then the flat washer (#E) onto the
SAME bolt (#D), in that order. Then insert one bolt assembly
through the MIDDLE hole and the other bolt assembly through the
BOTTOM hole of the right headboard leg (#3) and secure the bolts
using the Allen wrench (#G) to lock them with the headboard.
IV. For the assembly of the left headboard leg (#2) onto the
headboard (#1), repeat the process above.
(Back Side)
Note: Right and left headboard leg are determined by standing behind the bed.
#A x 2 pcs
#B x 2 pcs
#C x 2 pcs
#D x 4 pcs
#E x 4 pcs
#F x 4 pcs
Bolt Assembly For Top Hole Only
Bolt Assembly For Top Hole Only
Bolt Assembly For Middle and Bottom Holes Only
Bolt Assembly For Middle and Bottom Holes Only
Enlarged
Enlarged