Furniture of America Golva CM7295D User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7295D
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Phillips Screwdriver (Not Included)
Rev.16-09 -05

Page 2 of 6

Parts List Hardware List
#1 x 1 pc
Dresser
#2 x 4 pcs
Leg
#3 x 1 pc
Center Leg
#A x 8 pcs
Bolt 5/16” x 1-3/4”
#B x 8 pcs
Flat Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 8 pcs
Lock Washer
MD
#D x 1 pc
Allen Wrench
Page 3 of 6
#E x 8 pcs
Knob
#F x 16 pcs
Screw 5/32” x 1”
#G x 48 pcs
Plastic Washer
Due to the size and/or weight of this product, it is highly recommended that the
assembly should be done near the area of its intended location. Make sure you have
enough space to move around during the assembly. ALWAYS have at least two people
to help with transporting and assembling the product to avoid any potential injury and/or
damage.

I. With the help of another person,
carefully place the dresser (#1) on
its back over a protected surface.
Align the 4 legs (#2) with the pre-
drilled holes on the bottom corners
of the dresser (#1).
II. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through
the dresser (#1) using the Allen
wrench (#D) to lock them with the
4 legs (#2).
Page 4 of 6
Turn right (clockwise) to tighten
I. Align the threaded end of the
center leg (#3) with the pre-drilled
hole on the bottom center of the
dresser (#1) and tighten by hand
until secured.
II. Carefully place the dresser on its
upright position.
III. Adjust the leveler according to the
ground level. To lower or to raise
the center leg (#3), you need to
turn the leveler clockwise or
counterclockwise, respectively.
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
Turn right (clockwise) to tighten

I. Prepare the assembly of the
knob (#E) to the drawer of the
dresser (#1) by using 6 plastic
washers (#G) and two screws
(#F). See diagram for the
correct sequence in connecting
those parts.
II. Secure the screws (#F) from
the inside of the drawer using a
Phillips screwdriver to HAND-
TIGHTEN. Caution: Do not
use power tool and do not over-
tighten for damage to the glass
surface may result.
III. Repeat the above process to
assemble the remaining 7
knobs (#E) onto the drawers.
Page 5 of 6
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
#E x 8 pcs
#F x 16 pcs
#G x 48 pcs
#G#F
#1
Make sure the dresser is rested on a flat surface and it
does not feel loose or wobbly. If it does, double check
that the bolts/screws are secured and properly tighten.

Page 6 of 6
Drywall: Select a location where you want the dresser to be strapped. Mark on the wall the location
where the anchors (#C) will be placed. Drill two holes slightly smaller then the size of the screw (#D).
Push the anchor (#C) as far as it will go with your finger. Tap gently with a hammer until the anchors
(#C) are flush with the wall surface. Secure the bracket (#B) using a Phillips screwdriver to tighten
the two screws (#D) into the anchors (#C). Insert the flat end of the cable tie (#A) through the
bracket (#B) from the wall and through the bracket (#B) from behind the dresser and finally through
the open casing on the other side of the cable tie. Continue pulling the flat end until the loop is
tighten and locked.
-OR-
Wood Stud (Recommended): Find a wood stud behind the wall (no anchor is needed for wood
stud). Mark on the wall the location where the bracket (#B) will be placed. Drill two holes smaller
then the size of the screw (#D) into the wood stud. Align the bracket (#B) with the drilled holes and
tighten the screws (#D) using a Phillips screwdriver to secure the bracket (#B). Insert the flat end of
the cable tie (#A) through the bracket (#B) from the wall and through the bracket (#B) from behind the
dresser and finally through the open casing on the other side of the cable tie. Continue pulling the flat
end until the loop is tighten and locked.
SAFETY STRAP TO PREVENT TIP-OVER
Attach a bracket (#B) onto the back of
the dresser using a Phillips screwdriver
to secure it with 2 screws (#E).
CABLE TIE
BRACKET
ANCHOR