Furniture of America CM5003-TV User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-06-12
Page 1 of 17
DIFFICULT
ASSEMBLY RATING
CM5003-TV
2 PERSONS RECOMMENDED
Phillips Screwdriver
(Not Included)

Page 2 of 17

Page 3 of 17
This TV mount can accommodate a
flat-panel TV 27” to 50” with the
maximum weight capacity of 135 lbs.
CAUTION:
WEIGHT AND SIZE LIMITATIONS
Maximum TV Dimensions: 50”
Maximum TV Mount Weight Capacity: 135 lbs.
Maximum Top Tier Weight Capacity: 125 lbs.
Maximum Middle Tier Capacity: 40 lbs.
Maximum Bottom Tier Capacity: 40 lbs.
To prevent damage and/or injury, do not exceed the weight
or size limitation listed above. It is highly recommended
that the TV stand is secured with the enclosed safety strap
to prevent tip-over.
The maximum weight
capacity for the middle or
bottom tier is 40 lbs.
The maximum weight
capacity for the top tier is
125 lbs.

Before you begin, please read Page 2
“Assembly and Care Advice” and Page 3
“Weight and Size Limitations”.
And remember, do not tighten until each step is
completed or instructed.
Page 4 of 17
MD
PARTS LIST

Due to the size and/or weight of this product, it is highly
recommended that the assembly should be done near the
area of its intended location. Make sure you have enough
space to move around during the assembly. ALWAYS have
at least two people to help with transporting and assembling
the product to avoid any potential injury and/or damage.
Page 5 of 17
TV STAND HARDWARE LIST
Note: #R1, #R2 and #R3 are pre-assembled onto Part #1

Page 6 of 17
BRACKET HARDWARE LIST

Page 7 of 17
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

Page 8 of 17
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

Page 9 of 17
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten

Page 10 of 17

Page 11 of 17
Turn right (clockwise) to tighten

Page 12 of 17
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
ASSEMBLY IS COMPLETED
Make sure the TV stand is rested on a
flat surface and it does not feel loose or
wobbly. If it does, double check that
the bolts/screws are secured and
properly tighten.

Page 13 of 17
Turn right (clockwise) to tighten
Drywall: Select a location where you want the TV stand to be strapped. Mark on the wall the
location where the anchor (#M) will be placed. Drill a hole slightly smaller then the size of the screw
(#O). Push the anchor (#MF) as far as it will go with your finger. Tap gently with a hammer until the
anchor (#M) is flush with the wall surface. Secure the bracket (#L) using a Phillips screwdriver to
tighten the screw (#O) into the anchor (#M). Insert the safety strap (#N) through the bracket (#L)
from the wall and the bracket from behind the TV mount and pull the safety strap (#N) to tighten.
-OR-
Wood Stud (Recommended): Find a wood stud behind the wall (no anchor is needed for wood
stud). Drill a hole smaller then the size of the screw (#H) into the wood stud. Align the bracket (#L)
with the drilled hole and tighten the screw (#O) using a Phillips screwdriver to secure the bracket
(#L). Insert the safety strap (#N) through the bracket from the wall and the bracket from behind the
TV mount and pull the safety strap (#N) to tighten.
SAFETY STRAP TO PREVENT TIP-OVER

Page 14 of 17
Turn right (clockwise) to tighten
ATTACHING THE VERTICAL BRACKETS TO THE BACK OF TV
The hardware kits to mount the vertical brackets onto the back of the flat-panel
TV are included with the TV stand. These kits are compatible with flat-panel
TVs having either flat, curved or recessed style on the back. Please choose
the appropriate hardware kit for the type of TV that you have.
TYPE 1: Flat Back
Due to various pre-drilled hole sizes on the back of the flat-panel TV, please choose
one kit from the following four hardware kits that would be optimal to secure the right
and left vertical brackets (#12 & #13) onto the back of the flat-panel TV.
1. #S, #AA & #AG (4 pcs each).
2. #U, #AB & #AG (4 pcs each).
3. #W & #AC (4 pcs each).
4. #Y & #AD (4 pcs each).
#13

Page 15 of 17
Turn right (clockwise) to tighten
ATTACHING THE VERTICAL BRACKETS TO THE BACK OF TV
The hardware kits to mount the vertical brackets onto the back of the flat-panel
TV are included with the TV stand. These kits are compatible with flat-panel
TVs having either flat, curved or recessed style on the back. Please choose
the appropriate hardware kit for the type of TV that you have.
TYPE 2: Curved Back
Due to various pre-drilled hole sizes on the back of the flat-panel TV, please choose
one kit from the following four hardware kits that would be optimal to secure the right
and left vertical brackets (#12 & #13) onto the back of the flat-panel TV.
1. #T, #AA, #AG, #AG & #AE (4 pcs each)
2. #V, #AB, #AG, # AG & #AE (4 pcs each)
3. #X, #AC & #AF (4 pcs each)
4. #Z, #AD & #AF (4 pcs each).
#13

Page 16 of 17
Turn right (clockwise) to tighten
ATTACHING THE VERTICAL BRACKETS TO THE BACK OF TV
The hardware kits to mount the vertical brackets onto the back of the flat-panel
TV are included with the TV stand. These kits are compatible with flat-panel
TVs having either flat, curved or recessed style on the back. Please choose
the appropriate hardware kit for the type of TV that you have.
TYPE 3: Recessed Back
Due to various pre-drilled hole sizes on the back of the flat-panel TV, please choose
one kit from the following four hardware kits that would be optimal to secure the right
and left vertical brackets (#12 & #13) onto the back of the flat-panel TV.
1. #T, #AA, #AG, #AG & #AE (4 pcs each)
2. #V, #AB, #AG, # AG & #AE (4 pcs each)
3. #X, #AC & #AF (4 pcs each)
4. #Z, #AD & #AF (4 pcs each).

Page 17 of 17
Turn right (clockwise) to tighten
ATTACHING THE TV WITH BRACKETS ONTO THE TV MOUNT
Due to the size and weight of the TV, it is highly recommended that you
have at least two people to mount the TV onto the TV mount. Once you
have the TV mounted, secure it with the two bolts shown below.