Furniture of America CM-BK601 User manual

1 / 15
MODEL #
Questions?
GIVE US CALL: 1-888-980-5122
MON-FRI 8:30AM - 5:30PM (PST)
The Assembly Rating is a
5-point system showing the
level of effort needed to
assemble a specific product.
EASY DIFFICULT
3 - People
(Included)
Allen Wrench
Recommended
Phillips
Screwdriver
(Not Included)
CM-BK601
VERSION # 21-02-22

Thank you for your purchase!
We hope you enjoy this new addition to your home for many years to come.
Our commitment to providing quality products does not simply end when you purchase
our product. We fully stand behind our products from start to finish. Our customer
service department is available Monday – Friday 8:30 AM – 5:30 PM Pacific and can
help with assembly questions as well as, if necessary, replacing damaged or missing
parts. To help expedite our service, please have these assembly instructions readily
available, along with your order receipt.
E-MAIL
[e-mail]
Furniture of America
WEBSITE
www.foagroup.com
FOA Intro
FurnitureOfAmerica
foagroup
Monday to Friday
8:30AM- 5:30PM (PST)
Consumer Hotline
Toll-Free 1-888-980-5122
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessories listed on Page 6 are
accounted for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING
2/ 15

PRE ASSEMBLY
INTRODUCTION
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.
3/ 15

4 / 15

BUNK BED
5 / 15
#1 1pc #2 1pc #3 1pc
#5 1pc #6 1pc #7 1pc
#4 1pc
#8 1set
#9 1set #10 2pcs
CM-BK601
#11 2pcs #12 2pcs
#13 2pcs #14 2pcs #15 2pcs #16 1pc
Lower End
Guardrail Lower End
Guardrail Upper End
Guardrail Upper End Guardrail
Lower Front
Side Rail Lower Back
Side Rail Ladder Rail
Twin Slat Kit
(10pcs) Front Panel Side (Left)
Back Panel Bottom Panel Center Support
Full Slats Kit
(10pcs)
Side (Right)
Upper Front Side
Rail

6 / 15
#A 16pcs #B 16pcs #C 4pcs #D 4pcs
#E 4pcs #F 8pcs #G 16pcs #H 20pcs
Bolt
Ø1/4" x 3-1/4"
#I 1pc
Allen Wrench 4mm
Screw
#4x30mm
#17 1pc
Barrel Nut
Ø1/4" Screw
Ø1/4" x 3-1/8"
Upper Back Side Rail
Bolt
Ø1/4" x 1-9/16"
Metal Dowel
ɸ9*90mm Wood Dowel ɸ6*30mm Screw
#4x25mm

7 / 15
Exploded View
#1
#3
#17
#16
#4
#2
#6
#5
#7
#8 #9
#10
#11
#13
#12
#14
#15

CM-BK601 is packed in 2 cases
8 / 15
Carton Disignation Part Hardware
Lower End Guardrail
#C x 4pcs
Front Panel
Side ( Left )
Side ( Right )
Back Panel
Bottom Panel
Center Support
Lower Front Side Rail
Ladder Rail
Full Slat Kit
Twin Slat Kit
CM-BK601-1
CM-BK601-2
#A x 16pcs
#B x 16pcs
#D x 4pcs
#E x 4pcs
#F x 8pcs
#G x 16pcs
#H x 20pcs
#I x 1pc
#1
#2
#3
#4
#10
#11
#12
#13
#14
#15
#5
#6
#7
#8
#9
#17
Lower End Guardrail
Upper End Guardrail
Upper End Guardrail
Lower Back Side Rail
#16
Upper Back Side Rail
Upper Front Side Rail

ASSEMBLY INSTRUCTIONS
1
2
9 / 15
Part #1 x 1pc
Hardware #A x 8pcs
Hardware #B x 8pcs
Hardware #A x 8pcs
Part #2 x 1pc
Part #3 x 1pc
Part #5 x 1pc
Part #4 x 1pc
Part #6 x 1pc
Hardware #B x 8pcs
Hardware #D x 4pcs
#B
#I
#A
#1
#6
#5
#2
#I
#A
#B
#D
#3
#4
#16
#17
Part #16 x 1pc
Part #17 x 1pc
1. Align the ends of the lower front side
rail (#5) and the lower back side rail (#6)
to the pre-drilled holes along the sides
of the lower end guardrail (#1,2).
2. Insert the barrel nuts (#B)
into the rails, and align the
hole for the bolt.
3. Insert the bolt (#A) into the pre-
drilled holes along the side and
into the barrel nut (#B). Secure
using the Allen wrench (#I).
1. Align the ends of the rails
(#16,17) to the upper end
guard rails (#3,4).
2. Insert the barrel nuts
(#B) into the 2 bottom
holes along the rails.
Insert 3 bolts (#A) into
the pre-drilled holes
along the outer sides of
(#3,4) and into the barrel
nut (#C). Note, the top
hole does not go into a
nut. Secure bolts using
the Allen wrench (#I).

ASSEMBLY INSTRUCTIONS
3
4
10 / 15
Hardware #E x 4pcs
#E
#E
#E
5
#I
#I
#C
#C
#7
Hardware #C x 4pcs
Part #7 x 1pc
#1
#2
#3
#4
1. Insert a metal dowel
(#E) into the large pre-
drilled holes along the
top corners of the
bottom bunk.
2. With the help of another person,
carefully place the top bunk onto
those metal dowels (#E).
Align the top and bottom of the ladder (#7) to the pre-drilled
holes along the front rails. Insert a bolt (#C) into each end
from within the rails and secure using the Allen wrench (#I).

ASSEMBLY INSTRUCTIONS
5
6
11 / 15
#12
#10
#11
#F
x 2
Hardware #F x 4pcs
Part #10 x 1pc
#8
#9
Part #8 x 1set
Hardware #G x 16pcs
Part #9 x 1set
#G
#G
Part #11 x 1pc
Part #12 x 1pc
Apply the twin slat kit
(#9) onto the top bunk.
Insert a screw (#G) into
each end and secure
using a screwdriver.
Apply the full slat kit
(#8) onto the top bunk.
Insert a screw (#G) into
each end and secure
using a screwdriver.
1. Place the front panel
(#10) face down.
2. Insert a wood dowels (#F)
into the pre-drilled holes
along the corners of the
front panel (#10).
3. Place the right side
(#12) and left side
(#11) onto the other
ends of those wood
dowels (#F).

ASSEMBLY INSTRUCTIONS
7
8
12 / 15
Hardware #H x 4pcs #H
#14
Part #14 x 1pc
#12
#10 #11
Insert 2 screws (#H) into
the holes along the sides
of (#11/12). Secure using
a Phillips screwdriver.
Align the bottom panel (#14) to the ridges
along the sides and carefully slide in.

13 / 15
ASSEMBLY INSTRUCTIONS
9
10
x 2
Hardware #H x 4pcs
Hardware #H x 2pcs
Part #15 x 1pc
Part #13 x 1pc
x 2
#H
#13
#15
#H
#H
#14
Place the back panel (#13) and insert
2 screws (#H) into each end. Secure
using a Phillips screwdriver.
Align the center support (#15) to the
pre-drilled holes along the center
of the front and back panel (#10/13).
Insert a screw (#H) into each end
and secure using a screwdriver.
Repeat process for
second drawer.

11
14 / 15
ASSEMBLY INSTRUCTIONS
12
Make sure all screws and bolts are firmly secured.

15/ 15