Furniture of America CM7556Q User manual

Assembly
Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 16-11-23
CM7556Q
2 PERSONS RECOMMENDED
Tools Required For Assembly
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page 2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches
Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
Leg (L&R)
#4 x 1pc
Footboard
#A x 8pcs
Bolt Ø5/16" x 1-3/8"
#B x 8pcs
Look washer Ø5/16"
#Cx 8pcs
Flat Washer Ø5/16"
#D x 1pc
Allen wrench M4
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard Panel
#3 x 1pc
Leg Support
#5 x 2pcs
Rail
#6 x 4pcs
Slats
#7 x 4pcs Ø5/16"
Support Leg 240x30x30mm
#E x 8pcs
Screw #4 x 1-3/16''
Page 3 of 6

#1
#2R
#2L
#3
#A x 6pcs
#B x 6pcs
#C x 6pcs
#D
#A
#B #C
#A x 2pcs
#B x 2pcs
#C x 2pcs
#D
#A #B #C
#1
Page 4 of 6
Prepare 6 bolts assembly by inserting
lock washer (#B), then flat washer
(#C) onto bolts (#A). Align legs (#2R/
L) to the holes of the headboard panel
(#1). Secure with bolts (#A).
Prepare 2 bolts assembly by inserting lock washer (#B), then flat washer (#C) onto bolts (#A).
Align leg support #3) to the holes of the headboard (#1). Secure with bolts (#A).

#4
#5
#5
X4
#7
#6
#1
Page 5 of 6
Hook side rails (#5) to the latch of the headboard (#1) and footboard (#4). Make
sure the side rails (#5) are firmly connected to headboard and footboard.
Attach support legs (#7) to each slat (#6). Adjust floor protector according to ground level.

#E
ASSEMBLY IS COMPLETED
#E x 8pcs
#5
#5
#6
Page 6 of 6
Align the slats (#6) to the side rails (#5), then secure with screws (#E).