Furniture of America YNJ-317-4 User manual

Page 1 of 16
The Assembly Rating is a 5-point system that
show the degree of effort needed in assem-
bling a specific product (with 1 being easy and
5 being difficult). For most products, two per-
sons are recommended.
Allen Wrench
Phillips Screwdriver
Hammer
(Included)
(Not Included)
(Not Included)
YNJ-317-4
ASSEMBLY INSTRUCTIONS
ASSEMBLY RATING TOOLS REQUIRED FOR ASSEMBLY
EASY DIFFICULT 2 PERSONS RECOMMENDED

Page 1 of 15
Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 16

Page 3 of 16

Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION
Page 4 of 16

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly
Page 5 of 16

Page 6 of
VANITY TABLE AND STOOL SET
ASSEMBLY INSTRUCTIONS
Please keep for future reference
DIMENSIONS
15.4”(W) X 9.8”(D) X 16.4”(H)
DIMENSIONS
36.7”(W) X 15.7”(D) X 27.9”(H)
MODEL # YNJ-317-4
PARTS LIST
HARDWARE LIST
Before you begin, please
read “Assembly and
Care Advice”, “Pre-
Assembly Introduction”
and “Cam Lock Fastener
Assembly Instructions”.
16
A1PC
B1PC
C1PC
K1PC
D1PC
L1PC
E1PC
M1PC
1PC
G1PC
N1PC
1PC
H
F
O1PC
J1PC
I1PC
1PC
Q1PC
1PC
R
P
S1PC
T1PC
U1PC
V1PC
W1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
a
b
c
d
e
f
g
X
Y
ZZ
2PCS
2PCS
1PC
36.7''
27.9''
F
J
L
M
P
S
T
a
b
c
g
d
15.7''
15.4''
16.4''
9.8''
1
27PCS 227PCS
1PC
20PCS 20PCS 2SETS
4PCS
2PCS 10PCS
2SETS
8PCS
4SETS
1SET
5
4
4PCS 24PCS
367
89
10 11 12PCS
12
use screws on the other plastic pack
1/6

Page 7 of
VANITY TABLE ASSEMBLY
STEP1
Hardware #1 = 10pcs
STEP2
Hardware #1 = 10pcs
16
F
J
M
1
K
L
S
1
Insert the cam bolts (1) into the holes
and secure using a Phillips screwdriver.

Page 8 of
STEP3
Hardware #3 = 2pcs
Hardware #5 = 2 sets + 4 screws
Hardware #9 = 2 outer + 4 screws
STEP4
Hardware #4 = 12pcs
VANITY TABLE ASSEMBLY
16
5
5
X2
8
3
3
9
L
K
9
9
9
5
X2
PLUS
9
outer
inner
2nd hole
FRONT
FRONT
First remove the inner slide from the outer slide
of the runner ᬍby pushing down on the tab to
completely remove the two parts. Use only the
outer slides for this step.
Align the center holes (2nd hole) on each end of the inner slide ᬉwith the pre-drilled holes on Part K
and Part L. Slide the outer slide out of the way to expose the center hole (2nd hole) and use the two
screws to secure each inner slide. Note: The single screw hole near the rectangular opening on the
outer slide ᬉmust be in front position.
B
C
D
E
A
4
Y
V
Insert screws (4) and secure
using a Phillips screwdriver.
1. Remove the inner part 9 of the rails by
sliding out of the outer part 9 . Do so
by pushing down on the tab along the side.
Align only the outer
parts and insert screws.
2. Slide the outer part of the inner rail 5 out to expose the holes along the inner part. Align the 2nd holes
along each end of the inner parts 5 to holes along K & L . Use the 2 screws to secure the inner part
*Second hole*

Page 9 of
STEP5
Hardware #2 = 5pcs
Hardware #3 = 4pcs
Hardware #9 = 2 inner + 4 screws
STEP6
Hardware #2 = 2pcs
Hardware #3 = 2pcs
Hardware #4 = 4pcs
VANITY TABLE ASSEMBLY
16
F
B
C
D
E
A
V
9
9
9
2
3
H
I
W
2
1
H
J
W
3
8
4
G
Note: Assemble Part F
completely first before
as sembl ing t w o i nner s lides
9 onto Part D.
2. Align the INNER part of 9 to
the holes along the side of D ,
then insert the screws and secure.
1. Insert the dowels 3 into F . Insert the cam
locks 2 with the opening facing the hole,
then insert F and secure the cam locks 2 .
1. Apply glue, then
insert the dowel
3 into J .
2. Insert the cam locks 2 with the
opening facing the hole, then place
G & H onto J . Secure 2 .
3. Slide W into the ridges.
4. Insert the screws
4 and secure.

Page 10 of
STEP7
Hardware #1 = 4pcs
Hardware #11 = 2 hinges + 6 screws
STEP8
Hardware #2 = 4pcs
VANITY TABLE ASSEMBLY
16
8
P
Q
1
11181111
11
11
1111
11
O
P
Q
1
2
Refer to page #5 for cam lock assembly.