Furniture of America Valo CM3727T User manual

CM3727T
VERSION # 20-12-02
1 / 8

2 / 8
Thank you for your purchase!
We hope you enjoy this new addition to your home for many years to come.
Our commitment to providing quality products does not simply end when you purchase
our product. We fully stand behind our products from start to finish. Our customer
service department is available Monday – Friday 8:30 AM – 5:30 PM Pacific and can
help with assembly questions as well as, if necessary, replacing damaged or missing
parts. To help expedite our service, please have these assembly instructions readily
available, along with your order receipt.
E-MAIL
[e-mail]
Furniture of America
WEBSITE
www.foagroup.com
FOA Intro
FurnitureOfAmerica
foagroup
Monday to Friday
8:30AM- 5:30PM (PST)
Consumer Hotline
Toll-Free 1-888-980-5122
Prep Time!
Please review the assembly instructions and all
diagrams prior to assembling. Arrange parts as
recommended on Page 7 and group identical
hardware together to make assembling easier.
Check out our Quick Tips!
We recommend reviewing the pre-assembly
handouts. Even experts need a refresher now and
then!
Are you missing anything?
Double-check all parts, hardware and
accessories listed on Page 6 are
accounted for.
Should we send any replacements?
Are there any irregularities or flaws in the
parts? We can send replacements!
CHECK
BEFORE STARTING

PRE ASSEMBLY
INTRODUCTION
3 / 8
Suitable Location
Assembling near the area of the
intended location is highly
recommended.
Avoid Scratches
Use cardboard, blankets or a
carpeted area while assembling
furniture to prevent scratches.
Teamwork
ALWAYS have at least two people
to help with transporting and
assembling the product to avoid
potential injury and/or damage.
Flat Surface
Make sure the furniture rests on
a flat and level surface with each
leg evenly touching the floor.
Sufficient Space
Make sure you have enough
space to move around during the
assembly.
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.

4 / 8

CM3727T
TABLE
5 / 8

1
Part
Part
Hardware
Hardware
#3
#1
#A #A
#A
I. With the help of another
person, carefully place the
glass top (#1) facing down
on a protected surface.
II.Align the 2 legs (#3) with
the pre-drilled holes on the
bottom of the glass top
(#1).
III. Insert 4 screws (#A)
through the 2 legs (#3)
and secure those screws
using the Allen wrench
(#E) to lock them with the
glass top (#1).
7 / 8

2
3
Part
Part
Hardware
Hardware
Hardware
Hardware
#2
#3
#D
#D
#B
#C #C #C #C
#B #B
I. Align the base (#2) with the pre-
drilled holes of the 2 legs (#3).
II.Prepare 8 bolt assemblies by
inserting the lock washer (#C) onto
the screw (#B).
III. Insert the bolt assemblies through
the pre-drilled holes from the bottom
of the base (#2) and secure those
screws using the Allen wrench (#E)
to lock them with the legs (#3).
IV. Align the threaded end of the 4 glides
(#D) with the pre-drilled holes on the
bottom of the base (#2) and tighten
by hand until secured.
V. With the help of another person,
carefully place the table in upright
position. Make sure the table is
rested on a flat surface and does not
feel loose or wobbly. If it does,
double check that the bolts/screws
are secured and properly tightened.
8 / 8