Furniture of America YNJ-1414 User manual

The Assembly Rating is a 5-point system that
show the degree of effort needed in assem-
bling a specific product (with 1 being easy and
5 being difficult). For most products, two per-
sons are recommended.
ASSEMBLY INSTRUCTIONS
ASSEMBLY RATING
EASY DIFFICULT 2 PERSONS RECOMMENDED
Page 1
Phillips Screwdriver
Hammer (Not Included)
(Not Included)
YNJ-1414&1420
TOOLS REQUIRED FOR ASSEMBLY
15-07-10
Page 1

ASSEMBLY INSTRUCTIONS
Please keep for future reference
Page 6
NIGHTSTAND
MODEL # YNJ-1414&1420
PARTS LIST
HARDWARE LIST
Before you begin, please
read “Assembly and
Care Advice”, “Pre-
Assembly Introduction”
and “Cam Lock Fastener
Assembly Instructions”.
DIMENSIONS
23.62”(W) X 15.75”(D) X 24.33”(H)
A
EC
K
H
J
F
G
B
24.33
23.62 15.75
A
A
1PC
2PCS
1PC
G
A
L
1PC
M2PCS
C1PC
N2PCS
D1PC
O1PC
E
P
1PC
1PC
F1PC
H Q
1PC 2PCS
I1PC
J
R
1PC
1PC
K2PCS
B
122PCS 64PCS
26PCS 2PCS 8PCS 2SETS 4PCS
47
25 3
4PCS 4PCS 1PC 22PCS 8PCS 8PCS 4PCS
910 11 12 13 14 8
2PCS
15
Page 2

Page 5 of 13
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Page 3

ASSEMBLY INSTRUCTIONS
Page 7
STEP1
Hardware #1 = 14pcs
Hardware #2 = 4pcs
1
2
2
10
E
D
C
B
A
J
Insert the cam bolts (1) into the holes
shown below. Turn right to tighten.
Apply glue into the holes
along (J), then insert the
wood dowels (2)
Page 4

ASSEMBLY INSTRUCTIONS
Page 8
Assembling Drawer’s Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is composed of
an inner rail and outer slide. Please read completely first before assembling.
Mounting the Inner Rail (Fixed) of the Runner: Before mounting, please determine
which side of the panel is the front and rear. The single screw hole on the outer slide
MUST be positioned on the FRONT of the panel. Place the inner rail of the runner in
its correct position and flat on its back. Slide the outer slide out to the way to align the
center or second holes on both ends of the inner rail with the pre-drilled holes on the
panel. For most applications, the center or second holes are used but if not, just make
sure the appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner: Each outer rail is secured with
a single screw onto the FRONT SIDE of the drawer. Extend the two outer slidesof the
runners and place the drawer in between those two outer slides. Align the pre-drilled
holes on each side of the drawer with the screw holes of the outer slides. Use two
screws to secure from the inside of the drawer into the screw holes of the outer slides.
1
2
12
13
O
F
G
5
Screw Hole
2nd Hole
2nd Hole
front
front
outer outer
inner
Screw Hole
front
5
12
STEP2
Hardware #1 = 4pcs
Hardware #2 = 12pcs
Hardware #4 = 2sets
Hardware #5 = 4pcs
Hardware #12 = 8pcs
Hardware #13 = 8pcs
PLUS
4
4
outer
inner
First remove the inner slide from the outer slide
of the runner by pushing down on the tab to
completely remove the two parts. Use only the
outer slides for this step.
4
4
Page 5
Align the inner parts of (4)
and insert screws (13).
Align the outer parts of (4)
and insert screws (13).
Align rails (5) to the holes
and insert screws (12).
Insert the wood
dowels (2) into the
holes along the sides.

ASSEMBLY INSTRUCTIONS
Page 9
STEP3
Hardware #9 = 4pcs
Hardware #11 = 8pcs
STEP4
Hardware #2 = 6pcs
Hardware #11 = 6pcs
1
2
9
11
11
11
G
C
F
E
B
D
I
I
H
P
H
C
B
J
Page 6
Refer to page #3
for cam lock assembly.
Refer to page #3
for cam lock assembly.

ASSEMBLY INSTRUCTIONS
Page 10
STEP5
Hardware #11 = 4pcs
STEP6
Hardware #1 = 4pcs
Hardware #2 = 4pcs
Hardware #3 = 8pcs
Hardware #7 = 2pcs
Hardware #11 = 4pcs
Hardware #15 = 2pcs
1
7
2
3
11
11
A
O
K
LN
M
KQ
X2
15
Page 7
Align the door knob (7) to
the hole, then insert screw (6).
Refer to page #3
for cam lock assembly.
Insert screws (3)
Slide (Q) along the ridges.

ASSEMBLY INSTRUCTIONS
Page 11
STEP7
Hardware #6 = 4pcs
STEP8
Hardware #8 = 4pcs
Hardware #14 = 4pcs
6
14
8
Make sure the product is rested on a flat surface and does not feel loose or wobbly. If it does, double
check that the bolts/screws are secured and properly tightened.
Extend the two outer slides
of the runners so that they
are align with the sides of
the drawer. Make sure the
pre-drilled holes from the
drawer align with the screw
holes of the outer slides.
Secure two screws from the
inside of the drawer using a
Phillips screwdriver to tight-
en them to the outer slides.
ASSEMBLY IS COMPLETED
Page 8
Align (8) to the back, then
insert screws (14).