Furniture of America CM3559SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-02-26
Page 1 of 4
DIFFICULT
ASSEMBLY RATING
CM3559SC-2PK

Page 2 of 4

Parts List Hardware List
#1 x 1 pc
Back Rest w/ Legs
#2 x 1 pc
Seat Cushion
#3 x 2 pcs
Legs
#A x 1 pc
Allen Wrench
#B x 4 pcs
Bolt 5/16”x3-1/2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 2 pcs
Bolt 5/16”x2”
MD
#D x 4 pcs
Bolt 5/16”x2-1/4”
Page 3 of 4
#E x 10 pcs
Lock Washer 5/16”
#F x 10 pcs
Flat Washer 5/16”
#G x 1 pc
Wood Dowel
Note: The above parts and hardware are shown for a
complete assembly of ONE chair. However, the actual
parts and hardware in the box will be twice the quantity.
X 2

Step 1
I. Place the back rest with legs (#1) on a
protected surface. Insert the wood dowel
(#G) to the center hole of the back rest
with legs (#1).
II. Align the seat cushion (#2) with the wood
dowel (#G) and the pre-drilled holes of the
back rest with legs (#1).
III. Prepare 2 bolt assemblies by inserting
FIRST the spring washer (#E) onto the
bolt (#C) and then the flat washer (#F)
onto the SAME bolt (#C), in that order.
IV. Insert the bolt assembly through the hole
between the wood dowel (#G) and the
edge of the seat cushion (#2) and secure
that bolt using the Allen wrench (#A) to
lock it in with the back rest with legs (#1).
Repeat for the other side.
V. Prepare 4 bolt assemblies by inserting
FIRST the spring washer (#E) onto the
bolt (#B) and then the flat washer (#F)
onto the SAME bolt (#B), in that order.
VI. Insert 2 bolt assemblies through the two
pre-drilled holes in the corner of the seat
cushion (#2) and secure those bolts using
the Allen wrench (#A) to lock it in with the
back rest with legs (#1). Repeat for the
other side.
Step 2
I. Insert the 2 legs (#3) to align with the
pre-drilled holes of the seat cushion (#2).
II. Prepare 4 bolt assemblies by inserting
FIRST the spring washer (#E) onto the
bolt (#D) and then the flat washer (#F)
onto the SAME bolt (#D), in that order.
III. Insert 2 bolt assemblies through the two
pre-drilled holes in the corner of the seat
cushion (#2) and secure those bolts
using the Allen wrench (#A) to lock it in
with the leg (#3). Repeat for the other
side.
IV. Carefully turn the completed chair
upright. Make sure the chair is rested on
a flat surface and it does not feel loose or
wobbly. If it does, double check that the
bolts are secured and properly tighten.
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 4 of 4
2
#B x 4 pcs
#C x 2 pcs
#E x 6 pcs
#F x 6 pcs
#D x 4 pcs
#E x 4 pcs
#F x 4 pcs
C
Assemble everything exactly
the same for the second chair.