Furniture of America YNJ-1471C6 User manual

E-commerce-Enitial Lab
ASSEMBLY RATING
The Assembly Rating is a 5-point
system that shows the degree of effort
needed in assembling a specific
product (with 1 being easy and 5 being
difficult). For most products, two
persons are recommended.
EASY DIFFICULT
Page 1
ASSEMBLY INSTRUCTIONS
16.06.03
YNJ-1471C6
Tools Requiredfor Assembly
Phillips Screwdriver
Allen Wrench
(Not Included)
( Included)
2 PERSON RECOMMENDED
Hammer
(Not Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2

Page 3

Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION
Page 4

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Page 5
Note:Every cam lock bolt
must have a cam lock
connector in order to
fasten the parts together.
Align the cam
connector with its
side opening (or arrow)
pointing to the small
drilled hole.
Secure the threaded
end of the cam bolt
by using a screwdriver
Turn right (clockwise) to tighten.
(1)
Insert tge cam lock
bolt into the
pre-drilled hole
above the cam
connector.
(2) Two parts should
fit snuggly against
each other.
(3)
Turn right (clockwise) to tighten.
Turn the cam connector with
a screwdriver until it will not
turn any more with light to
moderate force.
(4)

HARDWARE LIST
Please keep for future reference
MODEL # YNJ-1471C6
PARTS LIST
CONSOLE TABLE
ASSEMBLY INSTRUCTIONS
43" (W) X15.4" (D) X34.3" (H)
DIMENSIONS
Before you begin, please
read "Assembly and
Care Advice","Pre-
Assembly Introduction"
and "Cam Lock Fastener
Assembly Instructions"
Page 6
34.3"
43"
15.4"
AAA
BC
E
K
D
A
B
C
D
E
F
G
H
I
J
K
L
M
N
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
116PCS 216PCS 310PCS 48PCS 54PCS 64PCS 74PCS
82PCS 94PCS 10 11 12 13 14 1PC16PCS 1PC 2PCS 68PCS

14
3
ASSEMBLY INSTRUCTIONS
Page 7
STEP1
Hardware #3=10pcs
Hardware #1=16pcs
1
1
1
1
1
1
11
1
1
1
1
1
1
1
1
11
3
3
3
3
3
3
3
3
3
A
H
G
C
E
J
B
F
3

Page 8
ASSEMBLY INSTRUCTIONS
Hardware #2=6pcs
Hardware #4=4pcs
STEP2
1
2
B
C
E
J
2
2
2
2
2
2
4
4
4
4
K
L
E
E
J

Page 9
ASSEMBLY INSTRUCTIONS
Hardware #2=2pcs
Hardware #5=4pcs
STEP3
Hardware #4=4pcs
Hardware #9=4pcs
Hardware #10=16pcs
Hardware #11=1pc
Hardware #12=2pcs
9
4
4
4
4
B
C
D
D
I
H
G
N11
910
5
2
5
2
12

Page 10
ASSEMBLY INSTRUCTIONS
Hardware #2=8pcs
Hardware #7=4pcs
Hardware #6=4pcs
STEP4
A
B
C
E
D
M
2
2
6
7
1
2
M
M

Page 11
ASSEMBLY INSTRUCTIONS
Hardware #8=2pcs
Hardware #13=68pcs
STEP5
ASSEMBLY IS COMPLETED
Make sure the product is rested on a flat surface and does not feel loose or wobbly. If it does, double
check that the bolts/screws are secured and properly tightened.
8
F
A
B
C
D
13
13
13
13
Extend the two outer slides of the
runners so that they could align
with the sides of the drawer.
Make sure the pre-drilled holes
from the drawer align with the
screw holes of the outer slides.
Secure two screws from the
inside of the drawer using a
Phillips screwdriver to tighten
them to the outer slides.