Futech QUATTRO User manual

QUATTRO
150.40.A
MANUAL

2
2
4
8
17
16
23
18
24
19
21
25
20
22
26 27 28 29 30 31
1
1
1
5
3
6
7
11
6
9
10
11
14
12
13
15
1. Magnet
2. LED indicator (orange)
3. LED indicator (green)
4. LED indicator (red)
5. Laser-sensitive area
6. Marking notch
7. Clamp
8. On/Off
9. Volume / Operating mode
10. Accuracy / LED activation
11. Bubble vial
12. Display
13. Type plate with serial number
14. Fixing thread for the clamp
15. Beeper
16. Battery door and latch
Display
17. “Rotary laser” mode
18. “Line laser” mode
19. Beeper Volume High
20. Beeper Volume Low
21. Beeper Volume Off
22. Battery Low
23. Battery OK
24. Accuracy: Coarse, 3mm
25. Accuracy: Medium, 2mm
26. Accuracy: Fine, 1mm
27. Much too low / Fast interval tone
28. Too Low / Fast interval tone
29. On-grade / Continuous tone
30. Too high / Slow interval tone
31. Much too high / Slow interval tone
32. No laser / No tone

QUATTRO
3
MANUAL
Depending on the selected operating
mode, the receiver detects either the
laser beams (red and green) of rotating
lasers or the (horizontal or vertical) laser
lines of line lasers with hand-held re-
ceiver function. Any other use than the
described above shall be deemed to be
improper use.
First use
Avoid violent shocks or dropping the
unit.
Inserting / changing the battery
Change tha battery if the batterysym-
bol (22) is displayed.
Open the battery cover (16)
Remove tha battery and insert a new
one (observe correct polarity)
Dispose ofthe used battery (see chap-
ter on environmental protection)
Operating
Switching the device on / off
Press the On / Off button (8)
Adjusting the volume
-
cessary repeated
switches the beeper volume between
High / Low / Off
Selecting the operating mode
Press the volume button (9) for at least
3 seconds.
switches from rotating laser to line la-
ser and vica versa
Adjusting the accuracy

necessary repeated
switches the accuracy of readings be-
tween Coarse / Medium / Fine
Activating / Deactivating the LEDs
Press the accuracy-button (10) for at
least 3 seconds.
Operating
Hold the device vertically (in case of a
vertical laser plane: horizontally) and
move it to the laserplane.
Please pay attention to the acoustic
signals and arrows on the (LED) dis-
play.
NOTE
When the device is switched on, it is
in the operating mode used before it
was switched off.
If in line laser mode, the device de-
tects only the line laser type which was
rst detected after the power on.
Maintenance and Care
Keep the device always clean, especi-
ally the laser-sensitive area!
Do not use aggressive cleaning
agents or solvents.
If soiled heavily the device can be cle-
anedunder running water.
Do not use high-pressure cleaner.
Allow it to dry completely before sto-
ring it in a closed container. Residual
moisture can result in corrosion of the
battery contacts. In this case our war-
ranty expires.
In the unlikely event of a failure or
defect, have the appliance examined
and repaired by Futech.
In all your queries and spare part or-
ders, always quote the serialnumber
(see type plate) of your device.

4
DECLARATION OF CONFORMITY
We herewith declare that this product conforms with the following standards and
directives:
Standards
DIN EN 61000-6-1
DIN EN 61000-6-3
in accordance with the regulations stipulated in the directives:
EC Directive
2004/108/EG
2006/95/EG
Technical changes reserved.
We accept no liability for printing errors.
TECHNICAL SPECIFICATIONS
 
 

 
 
 
 



 
 
 
 