Gabarron Elnur A-4 Mounting instructions

INSTALLATION INSTRUCTIONS
AND USER GUIDE
INDUSTRIAL HEATER
A-4
A-6
A-9
A-12
Please read these instructions before installing or
using this appliance for the rst time

Industrial Heater
2
1.- IMPORTANT INFORMATION
•The heater’s guarantee does not cover any damaged caused by the non-observance of any of these
instructions.
•This manual must be conserved and given to any new user.
•The installation must be performed in accordance with current electricity regulations.
•Check the voltage in the rating label is the same than supply.
•The use of these heaters is forbidden in any area where there is a presence of gases, explosives or
inflammable objects.
•Before carrying out any work inside the appliance, the heater must be disconnected from the electricity
supply.
•The heater must not be located immediately below a socket outlet.
•The heater must not be located in front of a socket outlet.
•The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to
touch the controls
•The installation of the heaters must be carried out in such a way that each pole can be disconnected
•The supply cord should not contact the surface of the heater.
•This appliance must be earthed.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the appliance
•WARNING: In order to avoid overheating, do not cover the heater.
•Do not position de heater near objects which will restrict the flow of heat.
•A minimum distance of 30cm is required for curtains and other combustible materials.
•The presence in the air of particles of smoke, dust and other pollutants could, in time, discolor the walls and
surfaces around the heater.
2.- INSTALLATION
Earth connection is required.
Ensure voltage is suitable for the heater. Refer to the rating label.
Pass cable through rear of the heater securing with cable grip.
For 3x400V + N~ connection, neutral wire is required.
Using the bracket, the heater can be positioned on the ceiling, wall or floor offering 360º directional movement.
3.- USING THE HEATER
A) Fan only
Switch with green light: Continuous operation of the ventilation fan.
B) Heating
Switch with red light: Operates the fan and heating working in conjunction with the thermostat.
Control thermostat: Regulates the room temperature switching the fan on / off. Rotate the control knob to the
maximum position. When the room reaches the required temperature gradually rotate the control knob to the
left until the red light goes out. The thermostat will automatically maintain the room temperature.
Delay thermostat: It operates the fan for a short period when the heating switches off to cool down the
elements.
Safety limiter: It disconnects the heater whenever there is an excess of temperature.
4.- MAINTENANCE
The heater does not require any special maintenance.
Disconnect the heater before cleaning or repair work.
Clean the entrance and exit grills only when the heater is cold.
Do not use abrasive or solvent cleaning products as these may damage the paint.
These heaters are manufactured under an assured quality system using environment friendly procedures.
Please take the heaters to a clean point once their useful life is finished, in order to recycle their materials in the
right way.

Industrial Heater
3
TECHNICAL SPECIFICATIONS
WIRING 230V~ (MODEL A-4)
WIRING 3x400V~+N (MODELS A-4, A-6, A-9 and A-12)
kW
kcal/h
Tensión
Voltage
m3/h
ancho
width
fondo
depth
alto
height
kg
A-4
Single phase
4
3.456
230V~
400
37cm
27cm
38cm
10
A-4
4
3.456
400V~3N
400
37cm
27cm
38cm
10
A-6
6
5.184
400V~3N
600
43cm
27cm
43cm
11
A-9
9
7.776
400V~3N
750
43cm
37cm
46cm
16
A-12
12
10.368
400V~3N
900
43cm
37cm
46cm
17
L Phase
N Neutral
PE Earth
C1 Contactor
I1 Fan only switch
I2 Heating switch
T Control thermostat
TR Delay thermostat
TS Safety limiter
M Fan
R1, R2, R3 heating elements
L Phase
N Neutral
PE Earth
C1 Contactor
I1 Fan only switch
I2 Heating switch
T Control thermostat
TR Delay thermostat
TS Safety limiter
M Fan
R1, R2, R3 heating elements
The symbol on the product or in its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your household waste disposal service or
the shop where you purchased the product. These instructions are only valid in the EU member states.

As a part of the policy of continuous product improvement Elnur reserves the right to alter specifications without notice.
INSTALLATION INSTRUCTIONS AND USER GUIDE WEB VERSION
ELNUR UK Ltd.
Unit 1, Brown Street North
Leigh, Lancashire
WN7 1BU
www.elnur.co.uk
Customer Service Department:
Telephone [phone]
[e-mail]
Manufactured by:
ELNUR, S.A.
Madrid, Spain
www.elnur-global.com
[email protected]
Management System International Certifications: