Gama Sonic 98B010 User manual

US patents
# 7172307, 9458970
ROYAL BULB SOLAR LAMP
Part # 98B010, 98B110, 98B310, 98B011,
98B111, 98B311, 98B012, 98B112, 98B312
Instruction Manual
Post/3" Fitter Mount
Pier Mount
Wall Mount

Thank you for your purchase! GAMA SONIC® solar charged lights are brighter and last
all night with a typical solar charge. Unique design, superior light output and numerous
installation options confirm the outstanding value of our product. GAMA SONIC® has been
recognized as a worldwide leader in the lighting industry for over 20 years.
Please read the instruction manual carefully to obtain the best results from your purchase.
Visit our website or download the latest version of your instruction manual:
www.gamasonic.com or www.gamasonic.com/user-guides
Technical Assistance / Warranty Claims / Replacement Parts
Toll-Free number: [phone] (only within the US) or www.gamasonic.com
For optimum light duration throughout
the night, it is very important to mount
your solar lamp in a spot where it will
receive the maximum amount of
direct sunlight throughout the
day.
NOTE: For best results,
the solar light must be
charged in the “High or
Low” position for at
least 2 days of full
direct sunlight.
Gama Sonic’s patented Bulb technology
gives your solar lamp the look and feel
of a traditional incandescent lamp. This
helps to distribute light further than
traditional solar lamps.
Gama Sonic's Bulb Technology What’s In The Box
Solar Lamp Location
page 2
EBulb
Hardware
C D
A B
98B012, 98B112,
98B312 only
98B011, 98B111,
98B311 only
98B010, 98B110,
98B310 only

3” Fitter Mount
NOTE: If you are replacing an existing gas
electric post light, you must consult a certified
technician to disconnect them before
installation.
1. Attach the 3” fitter fixture (D)
by sliding the mount over your
existing pole and secure using the
3 set screws.
NOTE: Be sure to not overtighten the set
screws.
Pier Mount
NOTE: There are specific types of screws for specific
surfaces. If you’re unsure of the appropriate type
of screw to use on your desired surface, please
consult a professional.
1. Use a drill to make tow holes in
the desired mounting location
(use the pier mount fixture (C) as
a template for drilling locations)
2. Insert the anchors into the holes and
secure the fixture (C) to the surface using
the provided screws.
Wall Mount
NOTE: Installing the light on a wall may limit
the solar panel for sun exposure. Make sure
the lamp is mounted so direct sun exposure
is available.
1. Remove the silver backet from
the Wall Mount Fixture (E) by
removing the two screw caps.
2. Use a drill to make two holes in the
wall where the lamp will be mounted.
(use the wall mount as a template
for drilling locations but make
sure to keep the two screw posts
horizontal)
3. Place the anchors into the holes
and secure the bracket to the wall.
4. Secure the wall mount fixture (E)
to the wall by sliding the fixture on
to the bracket and securing with the
two screw caps.
1. Remove the two screw caps from the top (B).
2. Install the GS Solar LED Bulb into the lamp by holding it at the base
and turning clockwise.
3. Turn the operation switch to your desired setting:
Low = Softer light output and longer duration
High = Brighter light output
4. Place the top (B) back on the fixture and secure with the two screw
caps.
5. Install the finial (A) into the top (B) by twisting clockwise.
Assembly Instructions Operation Instructions
Replacement Batteries and Bulbs are available at
www.gamasonic.com or via our Toll Free number: [phone]
Your Lamp can use the following bulbs:
A50WW10W – included bulb with Warm White LEDs (2700K)
A50BW10W – bulb with Bright White LEDs (6000K)
F30WW05W –Flame bulb with simulated flame LEDs
T45WW10W – Edison LED Bulb with Warm White LEDs (2700k)
Your Lamp uses two of the following battery:
GS32V30
Replacement Parts
page 3

Replacing the battery
page 4
Maintenance
Batteries are available for purchase at www.gamasonic.com
Troubleshooting
Clean the solar panels regularly with a damp towel to guarantee optimum performance. Do not use any type of
solvent for cleaning and be careful not to put too much pressure on the solar panels while cleaning.
WARNING: Do not dispose of Li-Ion batteries in the regular trash, municipal waste stream or by fire as batteries may
leak or explode. Do not open, short circuit, or mutilate batteries as injury may occur. Preserve our environment by
recycling Li-Ion batteries or disposing of them in accordance with local, State, and federal regulations. Do not mix old
and new batteries.
If your solar light does not come on as expected despite observance of all the instructions, please try the
following steps:
1. Make sure that the solar lamp is not being aected by any other light source.
2. Ensure the solar lamp is not positioned in the shade during the day.
3. Check that the batteries are installed correctly.
NOTE: The performance of the solar lamp will vary with the time of year. It will last longer when it has had a full
day in the sun rather than a day in overcast weather.
WARNING: Please keep out of reach of children. Do not dispose of the Li-Ion battery in the regular trash,
municipal waste stream or by fire as batteries may leak or explode. Do not open, short circuit, or mutilate
batteries as injury may occur. Preserve our environment by recycling Li-Ion batteries or disposing of them in
accordance with local, State and federal regulations. Do not mix old and new batteries.
WINTERTIME TIPS: For optimal performance, be sure to remove any snow or debris accumulation from solar
panel(s). A solar panel free of debris will charge the batteries much more eciently.
After several years of use, the battery may need replacing.
1. Remove the top (B) by unscrewing the two screwcaps.
2. Switch the unit OFF and remove the bulb.
3. Remove the screw and battery compartment cover.
4. Unclip and remove the battery.
5. Replace with a high quality Li-Ion 3.2V / 3000mAh battery with matching connector (Item GS32V30).
6. Install the battery in the compartment and secure the cover with the screw.
7. Repeat steps 3-6 for the second battery compartment.
8. Install the bulb and switch the unit ON to your desired setting.
9. Place the top (B) back on the fixture and secure with the two screw caps.