Gama Sonic GS-113F User manual

Introduction
Thank you for your purchase. GAMA SONIC®solar charged lighting eliminates the
problems associated with most solar lighting available today. GAMA SONIC®solar
charged lights are brighter and last all night with a full day solar charge. Unique
design, superior light output and numerous installation options confirm the
outstanding value of our product.
GAMA SONIC®has been recognized as a worldwide leader in the lighting industry for
over 20 years. The company also offers unique multi-purpose rechargeable products
that range from party lights to emergency lighting products.
For technical assistance and more information call our Toll Free number:
800-835-4113 (only within the US) or visit our website at:
www.gamasonic.com.
Please read the instruction manual carefully to obtain the best results from your
purchase.
Tools that are needed but not supplied with the solar post lamps are: screw driver,
power drill.
FLORA SOLAR LAMP
US Patent # 7172307
Instruction Manual

Solar Lamp Post Location
For optimum light duration throughout the night, it is very important to place your
solar lamp in a spot where it will receive the maximum amount of direct sunlight
throughout the day.
NOTE: For best results, the solar lamp post must be charged for two sunny days in
the “OFF” position,
Operation Instructions
1. Remove part (A) from part (B) by unscrewing the 2 screws. Turn the
operation switch (Fig. 1) to ON.
2. Reattach part (A) to part (B) and secure with the 2 screws. The Solar Lamp
will automatically come on at dusk
A
B
Fig. 1

Installation Instructions
GS-113F
NOTE: If you are replacing an existing gas or electric light, you must consult a
certified technician to disconnect the gas or electricity before installation of solar
lamp.
Place solar lamp on top of your existing 3” post and tighten the 3 screws
provided to secure the lamp.
GS-113P
Using the anchors screws, if needed,
1. Use electric drill to make two holes in the desired surface that match
the holes on the solar lamp base.
2. Place the provided screw anchors into holes.
3. Place the lamp base in line with the holes and screw the base onto your
desired surface with the provided screws.
GS-113W
NOTE: locate your solar lamp facing the south for best results.
Using the screw anchors, if needed:
1. Remove wall lamp support piece by unscrewing the bronze screw caps
from the back of the wall unit.
2. Use electric drill to make two holes in the desired location which
match the holes on the lamp support piece, and place provided anchors
into holes.
3. Place the wall lamp support piece in line with the holes and screw in
using the provided screws.
4. Attach solar lamp to wall support piece and secure with bronze screw
caps.
Replacing the Batteries
(After several years of use, the battery may need replacing).
1. Unscrew the two screws and detach part (A) from part (B). Make sure
the ON/OFF switch (Fig. 1) is in the OFF position.
2. Unscrew the battery compartment screw located on the silver reflector
and remove the battery compartment door.
3. Unclip the connector and remove the old battery. Make sure the new
battery is high quality 3.2V/1,500mAh Li-ion Rechargeable battery
with connector.
4. Clip on new battery and install into the battery compartment. Screw
back battery compartment door.
5. Reattach part (A) to part (B) and secure with the 2 screws.

WARNING: Do not dispose of Li-Ion battery in the regular trash, municipal waste
stream or by fire as batteries may leak or explode. Do not open, short circuit, or
mutilate batteries as injury may occur. Preserve our environment by recycling Li-Ion
batteries or disposing of them in accordance with local, State and federal regulations.
Do not mix old and new batteries.
Maintenance
Clean the solar panel regularly with a damp towel to guarantee optimum performance.
Do not use any type of solvent for cleaning and be careful not to put too much
pressure on the solar panels while cleaning.
Trouble Shooting
If your solar charged light does not come on at dusk despite observance of all the
instructions, please try the following steps:
1. Make sure that the solar lamp is not being affected by any other light
source.
2. Ensure the solar lamp is not positioned in the shade during the day.
3. Make sure the switch on the lamp head is in either the ON position
(Fig. 1).
4. Check that the batteries are installed correctly.
NOTE: The performance of the solar lamp will vary with the time of year. It will
deliver more light when it has had a full day in the sun rather than a day in overcast
weather.
WINTERTIME TIPS: For optimal performance, be sure to remove any snow or
debris accumulation from solar panel. A solar panel free of debris will charge the
batteries much more efficiently.
WARNING: Please keep out of reach of children.